LiftMaster ATS Support Question
LiftMaster ATS Support Question
Find answers below for this question about LiftMaster ATS.Need a LiftMaster ATS manual? We have 1 online manual for this item!
Question posted by jjkearns9 on August 10th, 2011
14' Ats Lightduty Total Length
I would like to know what the total length of a 14' ats light duty garage door operator
Current Answers
Related LiftMaster ATS Manual Pages
ATS2113X Manual - Page 1
....liftmaster.com
®
COMMERCIAL DOOR OPENER Model ATS 2113X 1/2 HP
For Residential And Light Duty Commercial Use Install on Sectional Doors Only
L
O
W
H
I
L
G
A
H NO R M
FOURPCE
L
O
W H
I
L
G
A
H NO R M
FDOORWCNE
Owner's Manual
■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■...
ATS2113X Manual - Page 2
... Electrical requirements 14 Install the Protector System 15-18 Fasten the door bracket 19 Connect the door arm to the trolley 20
Adjustment
21-23
Adjust the travel limits 21 Adjust the force 22 Test the safety reversal system 23 Test the Protector System 23
Operation
24-28
Operation safety instructions 24 Using your garage door opener 24...
ATS2113X Manual - Page 3
...piece garage doors. Maximum door size 14 ft. ft.)
Tools needed
During assembly, installation and adjustment of balance, call a trained door systems technician. Release the door. ... ALL ropes connected to garage door BEFORE installing and operating garage door opener to avoid entanglement.
• This product is out of this product on sectional garage doors ONLY.
Carpenter's Level ...
ATS2113X Manual - Page 4
... to eliminate the gap. See page 19 for lightweight garage doors (fiberglass, steel, aluminum, door with the installation of your opener. Safety Reversing Sensor
Vertical Centerline of Garage Door
Extension Spring OR
Torsion Spring
Access Door
Wall-Mounted Door Control
Safety Reversing Sensor
Gap between the bottom of the garage door and the floor MUST NOT exceed 1/4" (6 mm...
ATS2113X Manual - Page 5
Carton Inventory
Your garage door opener is packaged in Opener) Hex Screw 1/4"-20x5/8" (2) Lock Washer 1/4"-20x5/8" (2) Screw #8-32x3/8" (1) Washered Bolt 5/...Rail Support Bracket)
"C" Wrap (2)
Rail Support Bracket
Lighted Door Control Button
2-Conductor Bell Wire White & White/Red
Door Bracket
Door Bracket Plate
Curved Door Arm
Safety Reversing Sensor Mounting Bracket With Slot (2)
Chain...
ATS2113X Manual - Page 6
... the bracket to fingers from moving garage door opener:
• ALWAYS keep hand clear of motor unit. Chain
Opener
To avoid possible SERIOUS INJURY to the opener by inserting the #8-32x3/8" screw through a hole in each side flange and a matching hole in top of sprocket while operating opener.
• SECURELY attach rail support bracket BEFORE...
ATS2113X Manual - Page 7
...Rail
You have now finished assembling your garage door opener.
Please read the following warnings before
adjusting chain. Install garage door opener ONLY on wall next to garage door control.
11. Place manual release/safety reverse test label in garage door or opener mechanisms.
9.
If the chain
returns to the position shown when the door is open, do so.
8. An improperly balanced...
ATS2113X Manual - Page 8
Open your door to the highest point of the door. This height will provide travel clearance for the top edge of travel as shown here and on page 9.
3. An unbalanced garage door might NOT reverse when required. Header Wall
Unfinished Ceiling
2x4 Vertical Centerline of the garage door.
2. Close the door and mark the inside vertical centerline...
ATS2113X Manual - Page 10
Use packing material as shown.
• Insert a ring fastener to disconnect inner and outer sections. NOTE: If the door spring is used to garage door, rest garage door opener rail on 2x4 placed on the garage floor below the header bracket. HARDWARE SHOWN ACTUAL SIZE
Header Wall
Header Bracket
Chain Pulley Bracket
Ring Fastener Header Bracket
Clevis...
ATS2113X Manual - Page 11
... from a falling garage door opener, fasten it SECURELY to structural supports of the motor unit to required lengths.
3. Fasten the opener to structural supports before installing the opener. Concrete anchors MUST...brackets should be used if installing ANY brackets into masonry. Remove the 2x4. Operate the door manually. On finished ceilings (Figure 2), attach a sturdy metal bracket ...
ATS2113X Manual - Page 12
... the garage door. HARDWARE SHOWN ACTUAL SIZE
Screw 6ABx1-1/2"
Drywall Anchors
Insulated Staples
Outside Keylock Accessory Connections
To opener terminal screws: White to 2 and white/red to the opener. TO PREVENT THE MOTOR PROTECTOR FROM TRIPPING, DO NOT EXCEED 8 DOOR OPERATIONS PER HOUR.
FIXER L'ÉTIQUETTE PRÈS DE LA PORTE.
132A2112A
2-Conductor Bell Wire
Lighted Door Control...
ATS2113X Manual - Page 13
... the top of the red handle so "NOTICE" reads right side up as shown. Secure with a "Garage Door Opener" bulb.
INSTALLATION STEP 7
Install the Light
• Install a 75 watt maximum light bulb in the release arm of the outer trolley.
• Adjust rope length so the handle is 6 feet (1.83 m) above the floor. Then the...
ATS2113X Manual - Page 14
... Wire
Black Wire
14 To reduce the risk of the motor unit:
• Remove the motor unit cover screws and set the cover aside.
• Remove the attached 3-prong cord.
• Connect the black (line) wire to make it fit outlet. Be sure the opener is required by your garage door opener has a grounding type...
ATS2113X Manual - Page 15
... hardware) may interrupt the beam while the door is NO HIGHER than 6" (15 cm) above garage floor. Be sure power is closing, the door will stop and reverse to full open position, and the opener lights will detect an obstacle in masonry if repositioning is necessary to the garage door opener BEFORE installing the safety reversing sensor.
If...
ATS2113X Manual - Page 23
... open the door.
• Place the opener carton in the down position.
Door MUST reverse on contact with 1-1/2" high (3.8 cm) object (or 2x4 laid flat ) on the floor, centered under the garage door.
• Operate the door in the path of the door.
• Press the remote control push button to close from a remote if the indicator light...
ATS2113X Manual - Page 24
...is restored after 4-1/2 minutes. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.
5. Garage door MUST reverse on the floor. SAVE THESE INSTRUCTIONS. Using Your Garage Door Opener
Your opener will reverse. If open, the door will stop .
7. If closed .
If closing , the door will operate with the safety reversing sensor correctly installed and aligned)
1. The sensor has no...
ATS2113X Manual - Page 26
...away the existing grease from the garage door opener rail. Battery positive side up (+)
NOTICE: To comply with only 3V2032...door systems technician.
• Check to be sure door opens and closes fully. If it is required. Adjust if necessary. (See page 7.)
Every Year
• Oil door rollers, bearings and hinges. Reapply a small layer of operation.
CARE OF YOUR OPENER...
ATS2113X Manual - Page 27
... and try again.
5. The garage door opens and closes by a wall switch...door control terminals
and operate from the Door Control:
• Is the door control lit? One turn equals 2" (5 cm) of door arm length, close force or down force. Repeat the safety reverse test after the adjustment is a new
installation, check the down limit.
9. See Installation Step 10. • If the opener lights...
ATS2113X Manual - Page 28
... release handle. Operate the door manually. If it is unbalanced or binding, call a trained door systems technician. The door reverses for no apparent reason and opener lights don't blink:
• Is something obstructing the door? Use a
standard neck garage door opener bulb if regular bulb burns out.
14. The opener won 't work: • The garage door springs may be opened and closed...
ATS2113X Manual - Page 34
... homeowner to operate garage door opener from outside by disengaging trolley. Center Bracket (6 pcs.): Adds additional stability to open fully. Light Lens Cover: Attractive lens cover protects light bulbs and diffuses light to open garage door manually from portable remotes and a Light Feature for constant light.
Also can be limited to open fully.
376LM
CD1014 108D36
14 Foot (4.27...
Similar Questions
Alarm Going Off Almost Non-stop. Help!
Hello. I have an RSL12V unit for residential use. I went to open it the other day and the alarm trig...
Hello. I have an RSL12V unit for residential use. I went to open it the other day and the alarm trig...
(Posted by amcollectibles4 2 years ago)
Door Opener Only Moves 6 Inches
Opener Only Moves 6 Inches The Eyes Are Good And Down Force Is All The Way Up
Opener Only Moves 6 Inches The Eyes Are Good And Down Force Is All The Way Up
(Posted by trevorhahn 7 years ago)
Looking For The Rail Support Brackets For A 14' Rail On A Ats211r.
These 2 pieces form a clamp. They hold the top of the I rail for additional support. The 14 ' railSa...
These 2 pieces form a clamp. They hold the top of the I rail for additional support. The 14 ' railSa...
(Posted by Anonymous-56809 12 years ago)
Opener Shuts Door Then Opens Door With No Flashing Lights
MY OPENER SHUTS THE DOOR. THEN OPENS IT BACK UP AGAIN WITH NO FLASHING LIGHTS. LIFT MASTER 3280
MY OPENER SHUTS THE DOOR. THEN OPENS IT BACK UP AGAIN WITH NO FLASHING LIGHTS. LIFT MASTER 3280
(Posted by JCCO1017 12 years ago)