LiftMaster 3850 Support Question
Find answers below for this question about LiftMaster 3850.Need a LiftMaster 3850 manual? We have 1 online manual for this item!
Question posted by Jactrue on May 17th, 2014
How To Replace Battery Back In Liftmaster Wall Mount
The person who posted this question about this LiftMaster product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
There are currently no answers that have been posted for this question.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Related LiftMaster 3850 Manual Pages
3850 Elite Series Manual - Page 1
...;
GARAGE DOOR OPENER Models 3850
3850-267
For Residential Use Only
Com Details
The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1196 www.liftmaster.com
patible with
See Page 29 for
Owner's Manual
■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■ The door...
3850 Elite Series Manual - Page 2
... 25
Operation
26-33
Operation safety instructions 26
Using garage door opener 26
Using the wall-mounted door control 27
Using the remote control 28
Troubleshooting 28
The remote control battery 28
EverCharge® Standby Power System (optional 29
To open the door manually 30
Care of your garage door and/or the garage door opener if you see these Safety Symbols and Signal...
3850 Elite Series Manual - Page 3
... ALL locks and remove ALL ropes connected to garage door BEFORE installing and operating garage door opener to avoid malfunction and damage. To prevent possible SERIOUS INJURY or DEATH:
• ALWAYS call a trained door systems technician if garage door binds, sticks, or is out of the opener, instructions will call a trained door systems technician. If balanced, it should stay in...
3850 Elite Series Manual - Page 5
..."-18 (4) Lock Washer 5/16" (4) Screw 6ABx1-1/4" (2)
Self-Threading Screw 1/4"-14x5/8" (2) Screw 6-32x1" (2) Insulated Staples (10) Ring Fastener (3) Dry Wall Anchors (2) Rope Handle Rail Grease Carriage Bolt 1/4"-20x1/2" (2) Wing Nut 1/4"-20 (2)
5 Carton Inventory
Your garage door opener is packaged in the foam. Parts may be stuck in two cartons which contain the motor unit and...
3850 Elite Series Manual - Page 6
...tight against the trolley (Figure 3). To avoid SERIOUS damage to opener, ONLY use any other bolts will cause serious damage to door opener. • Position belt over belt pulley. Use of motor... Unit
To avoid installation difficulties, do not run the garage door opener until instructed to do so. • Remove the two washered bolts mounted on the square end. Washered Bolt 5/16"-18x1/2"
...
3850 Elite Series Manual - Page 7
...) on the floor.
13.
Install wall-mounted garage door control:
• within sight of the garage door.
• out of reach of children at minimum height of 5 feet (1.5 m).
• away from electrocution, disconnect ALL electric and battery power BEFORE performing ANY service or maintenance.
7 Install garage door opener ONLY on inside of the door.
10. NEVER wear watches, rings...
3850 Elite Series Manual - Page 11
.... You will need help at this point.
SECTIONAL DOOR OR ONE-PIECE DOOR WITH TRACK
A 2x4 laid flat is completed. To prevent damage to garage door, rest garage door opener rail on 2x4 placed on the trolley release arm to your door type as a support, raise the top of the opener to the floor, measure the distance from ceiling.
3850 Elite Series Manual - Page 12
... Washer 5/16" Nut 5/16"-18
Figure 3
FINISHED CEILING
(Not Provided) Bolt 5/16"-18x7/8" Lock Washer 5/16" Nut 5/16"-18
12 Measure the distance from a falling garage door opener, fasten it SECURELY to provide rigid support. Check to the structural support. 2. Concrete anchors MUST be different. Grease the top and underside of the hanging...
3850 Elite Series Manual - Page 13
... above wall surface.
• Position bottom of door control on the motor unit: white to white and white/red to door travel to 24 VOLT low voltage wires. DO NOT overtighten.
• Replace cover by gently prying at lower temperatures although the door control remains fully functional. The trolley will not return to each garage door opener. NOTE...
3850 Elite Series Manual - Page 14
... wear protective gloves and eye protection when changing the battery or working around the battery compartment. The lights will turn ON and remain lit for replacement. Then the lights will turn OFF.
• Reverse the procedure to close the lens.
• Use A19, standard neck garage door opener bulbs for approximately 4-1/2 minutes when power is in...
3850 Elite Series Manual - Page 15
...
Overhand Knot
INSTALLATION STEP 10 Electrical Requirements
To avoid installation difficulties, do not run the opener at least 1" (2.5 cm) from electrocution or fire:
• Disconnect ALL electric and battery power BEFORE performing ANY service or maintenance.
• Garage door installation and wiring MUST be grounded.
• Reinstall the cover. If the plug doesn't fit...
3850 Elite Series Manual - Page 16
... door as long as the wall framing.
Be sure power is necessary to mount the units on the left or right of the garage door (or door tracks, springs, hinges, rollers or other across the door,... the wall, the brackets must be connected and aligned correctly before the garage door opener will detect an obstacle in the down direction. If it is not connected to the garage door opener BEFORE ...
3850 Elite Series Manual - Page 24
.... The LED will flash quickly.
2. If the garage door opener cannot open and close the door (DOWN). Figure 1
n n
LED
Black Button Purple Button
Figure 2
Push Purple button twice to close the door.
1. Push the door control or programmed remote control again. If the door is not sticking or binding. The door must travel through a complete cycle, up and down...
3850 Elite Series Manual - Page 25
...).
Complete Adjustment Steps 1 and 2 Program the Travel Limits and Set the Force. The garage door opener will flash.
ADJUSTMENT STEP 3 Test the Safety Reversal System
TEST
• With the door fully open the door.
• Place the opener carton in the path of the opener. Without a properly installed safety reversing sensor, persons (particularly small children) could be tested...
3850 Elite Series Manual - Page 26
... are no effect in ; Failure to move .
• The Wall-Mounted Door Control: Hold the push button or bar down travel is activated. An improperly balanced door may be tested.
11. SAVE THESE INSTRUCTIONS. Activate your garage door opener, it is clear of SEVERE INJURY or DEATH:
1. If open door falling rapidly and/or unexpectedly, causing SEVERE INJURY or...
3850 Elite Series Manual - Page 31
...when the power is restored, and is operating off when door is open: • The garage door opener is against the stop . Using the Wall-Mounted Door Control, Light Feature.
6. The trolley should travel ....the opener by pulling the Emergency Release Rope. • Manually bring the door to a closed position. • Loosen the belt by a beep sounding every 30 seconds, replace the battery.
...
3850 Elite Series Manual - Page 32
..., replace the safety reversing sensors.
3 FLASHES
Door control or wire shorted.
4 FLASHES
Safety reversing sensors slightly misaligned (dim or flashing LED).
5 FLASHES
Motor RPM is not recognized. Bell Wire
Safety Reversing Sensor
Diagnostic Chart
Diagnostics Located On Motor Unit
"Learn" Button LED or Diagnostic LED "Learn" Button
Installed Safety Reversing
Sensor
Your garage door opener...
3850 Elite Series Manual - Page 34
... motor unit until the learn " button on any unwanted remote, first erase all codes: Press and hold the button on the door control.
2.
PROGRAMMING
NOTICE: If this Security✚® garage door opener is factory programmed to operate it has learned the code. All previous codes are not installed, two clicks will be heard...
3850 Elite Series Manual - Page 35
...press and hold the # button. Press the four buttons for your garage door opener. Release the # button.
2. It can be heard.
2. ...door should move . The opener light will be used up to confirm Learn Mode. The door should move . This feature has been activated at the factory.
LOCK
LIGHT
To change an existing, known PIN
If the existing PIN is already mounted outside the garage...
3850 Elite Series Manual - Page 38
... battery. EverCharge® Standby Power System: Provides backup power to protect LiftMaster® garage door openers against damage from lightning and power surges.
38 For use with NO access door. Surge Protector: The Garage Door Opener Surge Protector is open garage door manually from car, bedside, or anywhere in the garage. Also can be limited to operate garage door opener from...
Similar Questions
I Need A Replacement Lens Cover For Garage Door Opener Liftmaster Model #1355- 1
I need a replacement Lens Cover for a garage door opener Model # 1355M- 1/2 HP Liftmaste
I need a replacement Lens Cover for a garage door opener Model # 1355M- 1/2 HP Liftmaste
(Posted by nskanson 1 year ago)
How To Change Battery In Wall Control Garage Door Opener Model 3850 Liftmaster
(Posted by cjmanpiop 9 years ago)
How To Change Battery On Liftmaster Garage Door Opener Wall Unit
(Posted by tiar 10 years ago)
How To Remove Battery On Mounted Garage Door Opener
(Posted by tz188phyze 10 years ago)
How To Replace Battery On Liftmaster Garage Door Opener
(Posted by paeso 10 years ago)