Lexmark X464de Support Question
Lexmark X464de Support Question
Find answers below for this question about Lexmark X464de.Need a Lexmark X464de manual? We have 7 online manuals for this item!
Question posted by ElizabethMarhin on October 12th, 2011
Pc Kit
I replaced the photoconductor kit but warning still on screen
Current Answers
Answer #1: Posted by LexmarkListens on October 13th, 2011 2:25 PM
LexmarkListens
Member since:
July 1st, 2011 Points: 1,410,540
Member since:
July 1st, 2011 Points: 1,410,540
It is recomended to reset pc count when a new photoconductor is installed. To do this, go to the config menu and reset pc count or you can open the printers' front door while the machine is on and press and hold the cancel button until the resetting counter message appears.
If you need further assistance, please feel free to send us an email or you may contact Lexmark Technical Support.
Lexmark Listens
Phone:
USA: 1-800-539-6275
Canada: (877) 856-5540
UK: 0800 121 4726
South Africa: 0800 981 435
Related Lexmark X464de Manual Pages
User's Guide - Page 9
...supplies...235
Ordering toner cartridges...235 Ordering a photoconductor kit ...235 Ordering ADF replacement parts...236
Moving the printer to another ...location...236 Shipping the printer...237
Administrative support 238
Finding advanced networking and administrator information 238 Using the Embedded Web Server...238 Checking the device...
User's Guide - Page 12
80 Routine maintenance needed ...265 84 Replace PC Kit...265 84 PC Kit life warning...265 88 Cartridge low...265 88.yy Cartridge nearly low...266 88.yy Replace cartridge ...266 200-282.yy paper jam...266 290-295.yy scanner jam...266 293 Replace all originals if restarting job...266 293.02 Flatbed Cover Open ...266 294 ADF...
User's Guide - Page 235
... not covered under warranty. or A4-size plain paper. At this printer is near its end of this time, order a photoconductor kit. Warning-Potential Damage: Damage caused by the use of a supply or replacement item not produced by the manufacturer of life. Note: Repeat this printer. Ordering supplies
To order supplies in your printer...
User's Guide - Page 238
...printer, then print a network setup page and locate the IP address in the photoconductor kit, and capacity measurements of your Web browser.
Using the Embedded Web Server
If the... networking and administrator information
This chapter covers basic administrative support tasks. Checking the device status
From the Device Status page of the Embedded Web Server, it is available for a range ...
User's Guide - Page 265
Try one or more of the following :
• Replace the photoconductor kit. • Touch Continue to clear the message and continue printing.
88 Cartridge low
The toner is low. Install a new photoconductor kit.
84 PC Kit life warning
The photoconductor kit is exhausted. 59 Incompatible tray
Try one or more of the following:
• Remove the specified tray. • Touch Continue...
User's Guide - Page 312
...maintenance needed 265 84 PC Kit life warning 265 84 Replace PC Kit 265 840.01 ...screen 25
C
cables Ethernet 51 USB 51
calling Customer Support 292
canceling a job from Macintosh 102 from the printer control panel 102 from Windows 102
card stock loading 81 tips 97
Change to 255 Check tray connection 255 checking an unresponsive printer 254 checking an unresponsive scanner 273 checking device...
User's Guide - Page 316
...make copies 110 PCL Emul menu 225 PDF menu 224 photoconductor kit ordering 235 photos copying 105 port settings configuring 65 PostScript... change toner cartridge 260 31 Replace defective cartridge 260 32 Cartridge part number unsupported by device 260 34 Short paper 260 ... disk 265 80 Routine maintenance
needed 265 84 PC Kit life warning 265 84 Replace PC Kit 265 840.01 Scanner Disabled 267 841-846 ...
Service Manual - Page 37
... OPT PC PDF ...Multifunction Device Multifunction Printer Message handling Motor interface millimeter Modified modified read Multipurpose feeder Modem ready Masked Read Only Memory Microswitch NAND (usage: NAND gate) Nonvolatile Memory Nonvolatile Random Access Memory Operator correctable failure Original Equipment Manufacturer Overhead projector Optical photo conductor Optical Sensor Photoconductor...
Service Manual - Page 56
... Warning Replace the PC kit to ensure print quality.
84 Replace PC Kit
88 Cartridge Low
This warning is displayed when the cartridge is reset or menus are entered, or the printer is reset.
56 Standard USB Port Disabled
This message may occur at each 300K page count interval. Format the disk. Press Check to satisfy a Check Device Connections...
Service Manual - Page 58
... necessary. Inspect the input sensor flag and replace it if it . If the flag is loose, then replace it does not rotate freely or is too loose.
200.06 Imaged page not expected page (bouncy passthru sensor)
Remove the toner cartridge/PC kit. See "Engine board service check" on the input sensor...
Service Manual - Page 59
... not enough time since prior image finished to start new image)
Verify that the media is pointed upward and out of the PC kit for debris in the input tray, and replace if necessary.
200.16 Transport motor error detected
200.17 Took too long to the input sensor. If the flag is...
Service Manual - Page 60
...toner cartridge/PC kit and check for the printhead. Inspect the wear
laser servo cleanup is approved. "Printhead service check" on page 4-3. The alignment roller may be binding.
Replace the pick...the page stalled at the alignment gate. Inspect the wear strips in the tray, and replace if they are clean, not worn, or filled
with sensor and reversing solenoid removal" ...
Service Manual - Page 61
... page 4-28.
201.27 Page at fuser earlier than intended
Remove the toner cartridge/PC kit and check for obstructions in machine during warm-up . Check the paper path and remove any media in the exit guide, then replace the exit guide. Indicates code may be receiving more interrupts than expected, so it...
Service Manual - Page 85
...Try a different toner cartridge and PC kit.
• If those fail, then replace the LVPS/HVPS, controller board, ... temperatures, and humidity will POR. c. Scroll down to expose the photoconductor, resulting in the opening for cartridge damage. Blank page
FRU Toner cartridge...Also, see "Solving print quality problems" on the screen. Touch Print Quality Pages to print out the quality...
Service Manual - Page 86
... driver.
If this does not correct the problem, then replace the following FRUs one at CN203.
If the cable is more noticeable as the toner cartridge nears end-of the photoconductor causes an all black page. Make sure the toner cartridge and PC Kit are correctly installed and the high voltage contacts are installed...
Service Manual - Page 87
...Make sure recommended media is being used . Diagnostics information 2-49 Try a new PC Kit. Replace the transfer roll assembly if the springs or bearings show signs of wear, damage...in image density horizontally across page
FRU PC Kit (not a FRU)
Transfer roll
Action
The charge roll may have an unbalanced force against the PC (photoconductor) drum. Replace as necessary. Place a sheet of ...
Service Manual - Page 88
Recheck condition before replacing PC Kit, if necessary. Inspect the HVPS contact (transfer roll) for continuity. Banding is plugged ...the toner cartridge and PC Kit are installed correctly and that the laser beam is not blocked. Replace the LVPS/ HVPS or controller board as necessary. With the printer off, check to a variation in the speed of page
FRU Photoconductor kit (not a FRU)...
Service Manual - Page 89
The toner cartridge may be full. Inspect the fuser at its entry for debris.
• Make sure the media is straight and unwrinkled. • Replace the PC Kit, and recheck before replacing the toner cartridge. Check the paper path around the fuser entry. With the printer off , clear the path or clean the lens. The...
Service Manual - Page 110
7014-xxx
Reset Photoconductor Maintenance Counter (Reset PC Cnt)
This setting resets the photoconductor kit page counter and clears any warnings or photoconductor exhausted messages.
The event log can only be performed only after a new photoconductor unit has been installed. See "Reports" on the LCD. Press to return to menus. Selecting On (the default) allows
users to On...
Service Manual - Page 134
...correctly. The following screen displays and updates periodically... sensor (remove the cartridge and replace to actuate the sensor)
•...warn the user that this test may run the Disk Test/Clean Test:
1. Contents will be lost .
2.
To run the Quick Disk Test:
1. The test reads one block per track on a good disk. message displays to select Disk Test/Clean from DEVICE...
Similar Questions
What Is A Pc Kit And How Do I Replace It
What is a PC kit and how do I replace it
What is a PC kit and how do I replace it
(Posted by james78107 12 years ago)
