Lexmark X464de Support Question
Lexmark X464de Support Question
Find answers below for this question about Lexmark X464de.Need a Lexmark X464de manual? We have 7 online manuals for this item!
Question posted by EXPOINS on January 16th, 2013
Replace Pc Ket On Lexmark X464
I Just Change The Photoconductor On The Lexmark But I Dont Know How To Reset The Message On The Printer About The Replace The Pc Kit
Current Answers
Answer #1: Posted by LexmarkListens on January 17th, 2013 1:30 AM
LexmarkListens
Member since:
July 1st, 2011 Points: 1,410,540
Member since:
July 1st, 2011 Points: 1,410,540
You can do that from the Configuration menu:
- Turn off the printer.
- Press and hold 2 and 6.
- Turn on the printer.
- Release the buttons after 10 seconds.
- Reset Photoconductor Maintenance Count
Lexmark Listens
Phone:
USA: 1-800-539-6275
Canada: (877) 856-5540
UK: 0800 121 4726
South Africa: 0800 981 435
Related Lexmark X464de Manual Pages
Embedded Web Server Administrator's Guide - Page 9
... o (organization), c (country), or dc (domain)-separated by commas.
Notes:
• Supported devices can interact with the LDAP server. Using security features in the LDAP server where user accounts reside....Multiple search
bases may be able to access protected
device functions in the event of an outage that prevents the printer from communicating with the authenticating server.
•...
Embedded Web Server Administrator's Guide - Page 11
...encouraged to access protected
device functions in the event of an outage that prevents the printer from communicating with any form of authentication that relies on the printer control panel.
To... Base consists of the LDAP server where the authentication will not be configured. • Supported devices can store a maximum of five unique LDAP + GSSAPI configurations.
To add a new LDAP+...
User's Guide - Page 12
80 Routine maintenance needed ...265 84 Replace PC Kit...265 84 PC Kit life warning...265 88 Cartridge low...265 88.yy Cartridge nearly low...266 88.yy Replace cartridge ...266 200-282.yy paper jam...266 290-295.yy scanner jam...266 293 Replace all originals if restarting job...266 293.02 Flatbed Cover Open ...266 294...
User's Guide - Page 238
.... To view the device status:
1 Type the printer IP address in the address field of the printer, then print a network setup page and locate the IP address in the photoconductor kit, and capacity measurements of your Web browser.
Setting up e-mail alerts
You can have the printer send you do not know the IP address of your...
User's Guide - Page 265
..., the hard disk may be defective and require replacing.
80 Routine maintenance needed
The printer needs to clear the message and continue printing. Order a maintenance kit, which contains all the items necessary to replace the pick rollers, the charge roll, the transfer roller, and the fuser.
84 Replace PC Kit
The photoconductor kit is near exhaustion. 59 Incompatible tray
Try...
User's Guide - Page 312
...
57 Configuration change, held jobs were not restored 264 58 Too many flash options installed 264 58 Too many trays attached 264 59 Incompatible tray 265 61 Remove defective disk 265 62 Disk full 265 63 Unformatted disk 265 80 Routine maintenance needed 265 84 PC Kit life warning 265 84 Replace PC Kit 265 840...
User's Guide - Page 316
...by printer 93 where to load 93 Paper Weight menu 161 Parallel menu 175 pausing the current print job to make copies 110 PCL Emul menu 225 PDF menu 224 photoconductor kit ...PC Kit life warning 265 84 Replace PC Kit 265 840.01 Scanner Disabled 267 841-846 Scanner Service
Error 267 88 Cartridge low 265 88.yy Cartridge nearly low 266 88.yy Replace cartridge 266 900-999 Service 267 Answering 254 Change...
Service Manual - Page 37
... OEM OHP OPC OPT PC PDF PICS PIN PIXEL ...Lexmark Embedded Solution (applications) Laser Scanning Unit Low Voltage Low voltage power supply Megabyte Motor Driver Control Multifunction Device Multifunction Printer Message...Photoconductor Portable Document Format Problem isolation charts Personal identification number Picture element Printer Job Language Power-on reset Power-on self test Personal Printer...
Service Manual - Page 56
... Replace the PC kit to ensure print quality.
84 Replace PC Kit
88 Cartridge Low
This warning is displayed when the cartridge is low. The parts are not allowed with a defective disk. See "Maintenance kits" on the disk to hold the resources that have been requested to be defective.
80 Routine Maintenance
The operator panel displays this message...
Service Manual - Page 58
...flags or springs. • Debris in the printer and the driver.
200.03 The video never started on the manual input sensor. Replace the sensor if necessary. If so, then ... cartridge/PC kit. 7014-xxx
Cartridge error messages
Error 30 31 32
Description Invalid refill Missing or defective cartridge Unsupported print cartridge
Action Replace the cartridge. Repeating jams or jam messages can be...
Service Manual - Page 59
Carefully remove the tray and notice if the leading edge of the media is loose, then replace it. Remove the toner cartridge/PC kit.
Remove the toner cartridge/PC kit. Inspect the wear strips in the tray, and replace if they are worn. Check the main motor. See "Main motor service check" on the manual...
Service Manual - Page 60
... cause is that the media is approved.
Verify that the narrow media flag rotates freely and securely. Replace the pick tires if necessary. See "ACM pick tire roller removal" on page 2-40.
2-22 ...next
level of range due to the media being pre-staged in the tray. Remove the toner cartridge/PC kit and check for the printhead. if the media continues to go beyond what the control is not ...
Service Manual - Page 61
... to stop at fuser earlier than intended
Remove the toner cartridge/PC kit and check for obstructions between the input sensor and the fuser....flag is located behind the fuser exit rollers, about mid printer. See Go to "Rear exit guide assembly with the rear ...after it was never cleared. If there is found, then replace the damaged part.
sensor.
201.03 Video never started on...
Service Manual - Page 68
...
Printer has...Replace the controller board. See "Controller board service check" on the controller board is bad. See "Controller board service check" on page 2-35.
959.25 Insufficient device... space during initialization.
See "Controller board service check" on page 2-35.
959.22 Challenge secret failure
959.23 959.24
Self test failed during HW prog
959.26 Incremental counter reset...
Service Manual - Page 85
... expose the photoconductor, resulting in a 'dirty' print. Also, see "Solving print quality problems" on the right side for #4 contact from the front.
Unplug the printer, and check...quality. Try a different toner cartridge and PC kit.
• If those fail, then replace the LVPS/HVPS, controller board, or the printhead in printer service errors unless there is blockage of service...
Service Manual - Page 86
... noticeable as necessary.
If the toner cartridge and PC Kit are clean. Turn the printer on, and verify +24 V dc on the...photoconductor causes an all black page.
Make sure the toner cartridge and PC Kit are correctly installed and the high voltage contacts are installed correctly, then try a new PC Kit first and then toner cartridge.
If this does not correct the problem, then replace...
Service Manual - Page 87
...PC Kit.
Note: Do not touch the transfer roll except at the proper temperature to fuse the toner to the PC drum. Replace the transfer roll assembly if the springs or bearings show signs of paper over the roll to properly fuse. Try changing...media settings in the printer driver. The bearing ...PC (photoconductor) drum. Check the springs in image density horizontally across page
FRU PC Kit...
Service Manual - Page 88
...Replace the fuser as necessary.
2-50 Service Manual None of page
FRU Photoconductor kit (not a FRU)
Fuser
Transfer roll
HVPS or engine board
Action
Print a menu page from the Menu Settings Page in the Reports menu. With the printer...problem continues, then install a new toner cartridge. Recheck condition before replacing PC Kit, if necessary. Banding is primarily due to make sure that the...
Service Manual - Page 89
...printer off , clear the path or clean the lens. Inspect the fuser at its entry for debris.
Inspect the fuser at its entry for debris.
• Make sure the media is straight and unwrinkled. • Replace the PC Kit, and recheck before replacing... problems
Problem Light or blurred characters. Replace the PC Kit first, and recheck.
The toner cartridge or fuser may be defective....
Service Manual - Page 110
... "Reports" on position, the composite USB device is enumerated. If a user presses Menu ( ), they receive a message that appears in the on page 3-32. However, when set to Local from the Configuration Menu. [setting's current value] touch-screen.
2. 7014-xxx
Reset Photoconductor Maintenance Counter (Reset PC Cnt)
This setting resets the photoconductor kit page counter and clears any warnings...
Similar Questions
How Do I Get Rid Of The Warning Message After Replacing Pc Kit
(Posted by sandraharbourt 12 years ago)
Replace Pc Kit
Our printeer is reading replace pc kit. What doea this mean?
Our printeer is reading replace pc kit. What doea this mean?
(Posted by ajackson4780 12 years ago)
