Home » Kyocera » Multifunction Devices » Kyocera KM-3050

Kyocera KM-3050 Support Question

Find answers below for this question about Kyocera KM-3050.
Need a Kyocera KM-3050 manual? We have 25 online manuals for this item!

Kyocera Overview Questions Manuals Reviews Videos Research

Question posted by sankar8181 on December 12th, 2014

How To Fix On The Kyocera Km-3050 Error Code Cfb31?

How To FIX On The Kyocera Km-3050 ERROR CODE CFB31?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by zzed41 on December 12th, 2014 11:36 PM

This answer was accepted by the poster of the original question.

zzed41

Member since:
December 12th, 2014

Points: 914,010

1,160
points

Hi! CF codes are for Communication Failures. This can be caused by a misconnected wire from the panel to the body. If you cleaned the system, please check this. The 5-pin connector is usually misconnected to YC9 while it is supposed to be connected to the YC1 port. These are same-sized ports.

IF you did not do any cleaning or replacement of parts, then likely this is a panel failure. You will have to procure a new panel for it.

Hope this helps. If it does, please click on the "Accept Asnwer" button. If not, feel free to repost your question and state that this solution did not work.

Hope this helps! If it does, please click on the Accept Answer button. I will greatly appreciate it! :)

Answer #2: Posted by sabrie on December 13th, 2014 1:19 AM

sabrie

Member since:
May 23rd, 2013

Points: 3,306,778

100
points

Hello, please visit the link below and the discusion on the link carries the solution

http://www.thecopiernetwork.com/showthread.php?21663-KM-3050-error-CFB31-progrm-loading

www.techboss.co.za

Related Kyocera KM-3050 Manual Pages

PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 407

...G Graphics state, 228, 272 Gray pattern, 122 Grouping, 27 H Hard disk, 141, 246, 250, 256, 258 error codes, 136 I Image model, 299 International characters, 129 J Job, 136, 138, 140 printing a list of, 134 printing... copies by command, 145 K KCGL pen color, 297 KIR, 304 refinement level, 304 KPDL, 287 Kyocera Image Refinement, 304 L left, 307 Lightness, 155 Line, 73, 80, 82, 87 drawing by angle...

KM-NET for Direct Printing Operation Guide Rev-3.2 - Page 6

...Direct Printing by proceeding from the start menu > All Programs > Kyocera > KM-NET for Direct Printing. 2 KM-NET for Direct Printing When the installation is provided on the CD-... that came with the printing system. Installation and Startup 2. Startup Install KM-NET for installation. The installation program starts up automatically. Insert the CD-ROM that any of the computer.

PRESCRIBE Commands Technical Reference Manual - Rev. 4.7 - Page 215

... whose identity is given in plotter units if scaling is off, or user units if scaling is approximately 40. The error code is given by ASCII-coded integers in the following format: X, Y, P TERM X: x-coordinate in absolute plotter units Y: y-coordinate in the following table. This information is converted to 0.025 mm on both ...

PRESCRIBE Commands Technical Reference Manual - Rev. 4.7 - Page 251

... can be as follows: setpagedevice KPDL Error Messages Depending on the computer screen. Table 7.52. KPDL Error Messages Code Error Meaning 00 Cannot initiate KPDL 01 dictfull Dictionary full; Table 7.51. KPDL Error ## .. KPDL Operators keys to the CollateDetails parameter should have the following error codes will appear if errors occur and doautocontinue is set to the...

KM-NET for Accounting Operation Guide Rev-1.4 - Page 7

... administrator is logged onto the domain, then a password is complete, you can start KM-NET for Accounting by clicking the start menu > All Programs > Kyocera > KM-NET for Accounting 5 Select the checkbox for Use Windows Domain authentication to login to install KM-NET for Accounting without entering the administrator password. 2 Click Next. 3 Register a database...

KM-NET for Clients Operation Guide Rev-3.7 - Page 7

...the CD-ROM that the KX driver is completed, start the KM-NET for Clients by proceeding from the start menu > All Programs > Kyocera > KM-NET for Clients on the computer. Operation Guide 3 KX Driver... program starts up automatically. Installation and Startup 2.1. Installation Install KM-NET for Clients. Follow the installation instructions. 2.2. Installation and Startup 2.

KX Driver User Guide Version 5.90 - Page 2

... U.S. Examples of this guide is prohibited. Copyright © 2007 KYOCERA Corporation Copyright © 2007 Revised Edition KYOCERA MITA Corporation All rights reserved. The information in this guide is ...C5030N FS-C8100DN KM-1820 KM-2540* KM-2560* KM-3040* KM-3050* KM-3060* KM-4050 * KM-5050 * KM-6030 KM-8030 KM-C2520 KM-C3225 KM-C3232 KM-C4008 KM-C4035E KM-C3232E KM-C3225E KM-C2525E FS-1010...

Fax System (M) Operation Guide Rev-2.0 - Page 4

... 10 About Network FAX What is Network FAX 10-2 Setup 10-4 11 Troubleshooting Indicators During Sending/Receiving Operation 11-2 Precautions When Turning Power OFF 11-3 Error Messages 11-4 Troubleshooting 11-6 Appendix Character Entry Method Appendix-2 Specifications Appendix-5 Menu List Appendix-6 Received FAX Sizes and Paper Priority (Inch Model Appendix-9 Received FAX...

Fax System (M) Operation Guide Rev-2.0 - Page 218

...on, or unplug the power cord and plug it in the report and refer to the Error Code List on page 15 of papers used up with document data. FAX Box capacity is ...machine's Advanced Operation Guide. 11-4 OPERATION GUIDE Call service. If the message still appears, note the error code. Call your service representative. Refer to Send Result Reports on page 6-8 and FAX RX Result Reports...

Fax System (M) Operation Guide Rev-2.0 - Page 237

... line connection was stopped due to resend. U01100 - U01400 Failed to cancel reception. Ask the sender to establish connection with the recipient. U00420 - U01199 Communication error occurred during V34 communication, the U in the error codes is recorded in a pulse line system. Send again. U00810 Page(s) not sent correctly. U00900 - Send again. Send again...

Fax System (M) Operation Guide Rev-2.0 - Page 238

...-brand model and transmission restrictions were found set by the other party did not match the Local FAX ID on the receiving machine. Appendix-16 Error Code Possible Cause/Action U01600 Communication error occurred during reception of high-speed transmission. Designated transmission speed may not be received because no data. U01800 - U01821 Communication...

Fax System (M) Operation Guide Rev-2.0 - Page 239

.... Check with a sub address box function, or the sub address does not match. Check with the recipient. Specified sub address box is not yet registered. Error Code U03500 U03600 U03700 U04000 U04100 U04200 U04300 U04400 U04401 U04500 U05100 U05200 Possible Cause/Action Sub address bulletin board reception was attempted and the other...

Fax System (M) Operation Guide Rev-2.0 - Page 240

...this machine. Send again. Reception was stopped due to a data error occurring during transmission. Error Code U05300 U14000 U14100 U19000 U19100 U19200 U19300 U19400 Possible Cause/Action Reception... the data stored in the memory of this machine. Transmission to a data error occurring during reception. Send again. Transmission was stopped due to resend. Memory ...

Fax System (M) Operation Guide Rev-2.0 - Page 241

... Encryption Key 5-59 Encryption Key No. 5-59 Operation at the Receiving System 5-63 Operation at the Sending System 5-61 Registering an Encryption Key 5-60 Error Code List Appendix-15 Error Messages 11-4 F FAX Automatic Reception 3-11, 7-5 FAX Backup Kit 8-2 FAX Box Function 5-37 Checking 5-41 Deleting Originals from a FAX Box 5-40 FAX Box...

Scan System Operation Guide (Functions Edition) Rev-9 - Page 19

... Dialogue Box 3-137 Setting Up the PDF Keyword Assist Option 3-138 Supplemental: Making Settings related to the 'Access according to sender name' option 3-146 Appendix A Error Codes A-1 Appendix B Error messages B-1 Appendix C Specifications C-1 xviii

Scan System Operation Guide (Functions Edition) Rev-9 - Page 246

.... An attempt to use the Send E-mail function was made, but was unable to access the corresponding information in progress was canceled by the operator. Error Code E001 E010 E011 E012 E020 Cause of your Operation Guide. Check to make sure that there are connected properly. The transmission log can be classified...

Scan System Operation Guide (Functions Edition) Rev-9 - Page 247

... already connected to another scanner. • Check to find . Increase the available space on the destination computer ran out of Error Procedure for Correction The destination for SMTP Authentication are correct. Error Codes Error Code E021 E022 E023 E024 E030 E031 E032 Cause of available space. The mail contained an e-mail address that Check to...

Scan System Operation Guide (Functions Edition) Rev-9 - Page 249

..., fix that problem. Verify the host name or the IP address of the FTP server is trouble in the information for Correction The response received from the transmitting computer was not an appropriate one . Check the computer of each group member as necessary and, if there is not set correctly. Error Codes Error Code E039...

Scan System Operation Guide (Functions Edition) Rev-9 - Page 250

... FTP server matches the path setting registered in the FTP server. Check each error and fix the corresponding problem(s). E082 The storing path is permitted to login. Page A-6 Error Codes Error Code E081 Cause of unexpected response from the FTP server. E101 An error has occurred while selecting multiple destinations. The storage folder is not found or...

3050/4050/5050 Operation Guide Rev-3 (Basic) - Page 22

... the seller, nor any other rights, which vary from whom the product was purchased. For model KM-3050 - This warranty does not cover Maintenance Kits or the components of Maintenance Kits, which consist of the Authorized Kyocera Dealer in material and workmanship as "MFP"), and the new accessories installed with the initial installation...