Kenmore HE2t Support Question
Kenmore HE2t Support Question
Find answers below for this question about Kenmore HE2t - 3.7 cu. Ft. Front Load Washer.Need a Kenmore HE2t manual? We have 1 online manual for this item!
Question posted by jimkelley31050 on November 4th, 2015
Cloths Washer Spin Cycle
I recently bought a home that has a Kenmore washer in the purchase. When I do a normal wash cycle it seams like the spin cycle only tries to spin for a very short time (seconds) two or three times during the cycle like it is not being held in that cycle. The clothes come out wet still. I thought the drain hose might be blocked but if I then put it in spin and drain it goes through a reasonable time frame of spinning and the clothes come out ready for the dryer. I don't have the model or serial number with me but is there a part in the cycle control control that might be causing this? When I get the model and serial numbers what part will I ask for?
Current Answers
Answer #1: Posted by TechSupport101 on November 5th, 2015 1:43 AM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,305
Member since:
May 24th, 2013 Points: 12,171,305
Hi. Link to any of the issues that seems closet to the Kenmore washer issue you are facing off the washer problems troubleshooting web links here http://www.repairclinic.com/RepairHelp/Washing-Machine-Repair-Help
Related Kenmore HE2t Manual Pages
User Guide - Page 8
... lbs. (8 kg)
N/A
36.0" 30.00"
27" 242 lbs.
17.64 lbs. (8 kg)
N/A
36.0" 30.00"
27" 242 lbs.
1-4 SPECIFICATIONS
Model Number Model Description
Color
Capacity (Cu.Ft. IEC) Temperature Control
Heater Sensors
Tumble Speed
Spin Speed
Motor Voltage Frequency Amps Water Consumption Average DOE (Gallons-Per-Cycle) Rated Load Load Pounds
Height Install Depth: Min -
User Guide - Page 9
... 285834; U-shaped hose form B. If you are in the washer drum. and connector kit, Part Number 2858835
4 ft (1.2 m) drain hose extension kit, Part Number 2858863
2 longer water fill hoses: 6 ft (1.8 m) Part Number 76314 10 ft (3.0 m) Part Number 350008
A
B
C
D
OPTIONS
Pedestal
You have the option of purchasing pedestals of the items listed here, call the toll...
User Guide - Page 19
... STEEL DRUM
The stainless steel drum eliminates corrosion and enables higher spin speeds for more clothes at the beginning of the cycle the Add A Garment status light will have less moisture than for a conventional washer.
For some cycles, the default spin speed can obtain the same washing results for delicate items and is no agitator, you are...
User Guide - Page 22
... of the cycles by pushing it without clothes.
For All Wash Cycles
1.
See "To cancel a cycle" in component failures and noticeable mold or mildew. Turn on the washer by pulling on the handle. When selecting a Wash Cycle, the preset Modifiers and Options, Water Temp, and Spin Speed for a medium-sized load. See "Wash Cycles."
5. To load washer
Open the washer door by...
User Guide - Page 24
... Options after the wash cycle.
Use a measuring cup with all Options are locked.
3-6 To pause the washer at the best time during the first rinse after the cycle has started
1. To stop a cycle and select a new cycle
1. If the option is complete, the door unlocks. Select and hold START (for approximately 1 second) to restart the washer at the...
User Guide - Page 25
...When CONTROL LOCKED is selected.
All cycles have preset Options. The washer will cancel the Wash Cycle. The indicator light for approximately 1 second).
3. The preset settings provide the recommended fabric care for different types of your water pressure, water temperature, detergent, and clothes load. Select PAUSE/CANCEL. The cycle time will be added.
2.
To change up...
User Guide - Page 26
... bleach is unbalanced. Heavy Duty
Use this cycle to wash loads of sturdy, colorfast fabrics and Heavy soiled garments. Preset Cycle Settings
Each cycle has a preset Cycle Time, WASH/ RINSE TEMP, and SPIN SPEED. The preset settings provide the recommended fabric care for cleaning loads of heavy soils and stains. Normal/Casual
Use this cycle to help ensure the removal of soiled...
User Guide - Page 27
... overview of possible options for each Wash Cycle selection.
• If an option is available with a selected cycle, the light for that option will be a short tone and the light for equal distribution of the laundry, and a soaking time without spin assures gentle treatment, even for :
• Loads that you are part of normal washer operation. IMPORTANT: Do not place...
User Guide - Page 28
... to aid in the removal of load you are washing. Wash Temp
Each cycle has a preset water temperature setting. To change the spin speed, select the SPIN SPEED button until the desired setting ... for fabrics. This option adds tumbling time prior to keep laundry additives from the washer as soon as in "Cycles."
• ATC works for the wash temperature with the same water temperature as...
User Guide - Page 29
... items marked "Hand Washable"
Clean Washer No clothes
Rinse & Spin
All loads
Drain & Spin
All loads
Soak
All loads
Delay Wash
AVAILABLE OPTIONS
Extra Rinse
Pre
End of these washer cycles.
Listed to the right are the options available to the chart below for suggested load types and their corresponding cycles. CYCLE
SUGGESTED LOAD TYPE
Sanitary
Heavily soiled underwear, towels...
User Guide - Page 30
...time.
4. a) If no items are detected in the washer, it will determine if clothing or other items are found, wipe down area thoroughly with a dry
cloth and let the washer... while the washer runs a short sensing cycle.
A RINSE/SPIN cycle must then be interrupted by pressing the PAUSE/CANCEL button.
Press START. a) Mix a dilute solution, using a damp cloth. The cycle will proceed ...
User Guide - Page 31
....
• Turn off both water faucets.
3-13 Put 1 qt (1 L) of time, you will not freeze. Unplug washer or disconnect power.
4. Turn on a Drain/Spin cycle.
3. Occasionally wipe the outside of hose failure. NOTE: Do not wash components in the hoses, freezing can damage your washer to allow for other causes. WATER INLET HOSES
Replace inlet hoses...
User Guide - Page 32
... shock.
4. Use 1/2 the manufacturer's recommended amount for a medium sized load.
3-14 Unplug the power cord.
3. Do not reuse transport bolts.
Reinstalling the washer
1. Use only HE High Efficiency detergent. Run the washer through the Normal/ Casual cycle to locate, level and connect the washer.
2. Use only HE High Efficiency detergent. Unit must...
User Guide - Page 33
... not use an extension cord. Re-select cycle and press START.
• "Spin," "Wash" (HT "Rinse,""Cycle Complete") and "Add a Garment" illuminated or "F21" on display (Drain Problem) Select PAUSE/CANCEL twice to cancel the cycle.
This happens during the end of normal washer operation. It is normal.
• Are you washing items with any new product, you will...
User Guide - Page 35
... to follow these instructions can result in the cycle? Reinstall hoses, turn on washer? The washer pauses for leaks.
• Is the washer in a normal pause in death, fire, or electrical shock.
• Is the power cord plugged into a grounded 3 prong outlet. Press and hold START, for 1 second? The drain hose should be removed for...
User Guide - Page 36
..., and clothes load. Spin time is added if an unbalanced load is normal. When using the Quick Wash or Delicate cycles, you washing many loads? Follow manufacturer's recommendations for smaller load sizes (2-3 items) of load you overloaded the washer? The cycle time will start a Drain/Spin cycle. Wash water colder than 60°F (15.6°C)? Make sure your wet laundry in...
User Guide - Page 81
...been opened during high-speed spin, the door unlocks after 3... for more than 5 seconds. Check/clean drain pump...the door unlock has failed 6 times.
Unplug washer or disconnect power. 2. Possible Causes...clothes from dispenser motor to the left when facing the MCU connectors. If a failure occurs during 3 consecutive cycles...and start of the CLEANING WASHER cycle a load is not located
near ...
User Guide - Page 82
... a NORMAL cycle without tumbling, the water will be drained and it is not plugged or kinked.
2. Check the drain hose and make sure it will try to spin or drain again. Check wire harness connections to show the failure codes. Verify CCU operation by the pressure switch during the drain or spin phases, the washer will...
User Guide - Page 87
....
To remove the touchpad/LED assembly:
1. Disconnect touchpad/LED assembly wire harness from the washer.
2. To remove Motor Control Unit (MCU):
1. Pull back the seal to inspect all...RINSE/SPIN cycle must then be interrupted by the dispenser drawer.
5. Gently pry up and slide the MCU forward. Remove left front screw that follows:
a) Mix a dilute solution, using a damp cloth. Under...
User Guide - Page 88
... while the washer runs a short sensing cycle.
Once the cycle has begun, allow for other items are detected in the washer, all cycle lights will flash and the WASH and CONTROLS LOCKED lights will cause product damage over time.
4. The door will take approximately 3 minutes.
7. Select the CLEAN WASHER cycle.
6. This will unlock. The cycle will determine if clothing or...
Similar Questions
F20 Error
My washer fills with water and then stops after about 6min with an F20 error. I am able to run the r...
My washer fills with water and then stops after about 6min with an F20 error. I am able to run the r...
(Posted by abakshi 9 years ago)
He2t Washer Is Loud When In Spin Cycle
(Posted by bbridcar 10 years ago)
My Washer Works But It Wont Go Into Spin Cycle It Drains The Water But Wont Spin
(Posted by cire503 10 years ago)
Kenmore Elite Top Load Washer Purchased In 2011. Received Recall Notice For Posi
(Posted by laryadkins32 11 years ago)
Cloths Washer Will Not Start
I have a kenmore elite HE3T washer and the wash cycle indicatorsw blink but the washer will not star...
I have a kenmore elite HE3T washer and the wash cycle indicatorsw blink but the washer will not star...
(Posted by Anonymous-24355 13 years ago)