Kenmore HE2t Support Question
Kenmore HE2t Support Question
Find answers below for this question about Kenmore HE2t - 3.7 cu. Ft. Front Load Washer.Need a Kenmore HE2t manual? We have 1 online manual for this item!
Question posted by riskoj on May 20th, 2017
Follow Up To The Kenmore He2t Washer F20 Error Code.
I replaced the pressure switch and the water inlet valve with a new, hem parts. After restarting the machine, the F20 code was back, again about 6 minutes into hot, cold, mix cycle. I discovered what appears to be a small water leak in the pressure valve hose. The coupling between the hose and the tub drain is soaked, and a small amount of water is dripping into the bottom of the machine. i going to replace the hose and see if that solves it. Thoughts?
Current Answers
Answer #1: Posted by Odin on May 20th, 2017 4:45 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,700
Member since:
April 10th, 2010 Points: 41,236,700
That's a good plan.
If the problem persists or if you require further explanation, see https://www.shopyourway.com/questions/1079525.
If the problem persists or if you require further explanation, see https://www.shopyourway.com/questions/1079525.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Kenmore HE2t Manual Pages
User Guide - Page 3
... 2-1 Installation Instructions 2-6
PRODUCT OPERATION 3-1 Features And Benefits 3-1 Washer Use 3-3 Washer Care 3-12 Troubleshooting 3-15
COMPONENT ACCESS 4-1 Component Locations 4-1 Removing The Console And The Touchpad/LED Assembly 4-2 Removing The Central Control Unit 4-4 Removing The Water Inlet Valve 4-6 Removing The Pressure Switch 4-7 Removing The Line Filter & Power Supply Cord...
User Guide - Page 15
...is connected to water leakage.
Laundry tub drain or standpipe drain
Connect the drain hose form to the washer's hot (H) water inlet valve. B. Cold water inlet
1. Check the temperature of hose failure. Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found. Read and follow these instructions.
Clear the water lines
1. Run water through both faucets...
User Guide - Page 22
... the ADD A GARMENT light is helpful when you do not select START within 5 minutes of choosing a cycle, the washer automatically shuts off.
3-4 This wash system, along with less water, will be fully loaded, but not tightly packed. Do not overload washer. Open the dispenser drawer and add laundry additives to use. If desired, select the END OF...
User Guide - Page 26
...°C)
0:39
Warm
95°F (35°C)
0:56
N/A
0:26
Cold
68°F (20°C)
0:14
N/A
0:29
Cold
68°F (20°C)
Spin Speed
High High High High High
Low Low High High No Spin
* The cycle times vary automatically based on your water pressure, water temperature, detergent, and clothes load. Hot washing temperatures assure optimal bleach activity. This...
User Guide - Page 28
... until the desired setting is a preset setting for fabrics.
Select a water temperature based on the cold water at the faucet. Follow garment label instructions. ATC regulates incoming hot and cold water.
End of detergent or bleach residue from the washer as soon as in the removal of Cycle Signal
This signal is illuminated. You may be used to aid...
User Guide - Page 31
...;ooding (due to a water pressure surge) while you are away.
• Slightly open after five years of washer interior.
Shut off the water supply to complete.
9.
Flush water pipes.
2. 8. Remove the inserts (the siphon from faucets and drain. WATER INLET HOSES
Replace inlet hoses after each cycle to the drawer. Periodically inspect and replace inlet hoses if bulges, kinks...
User Guide - Page 32
...'s recommended amount for a medium sized load.
3-14 Reinstalling the washer
1.
To transport the washer:
1. Follow the "Installation Instructions" to follow these instructions can result in the drum. Unplug the power cord.
3. Disconnect the drain hose from faucets, then drain the hoses and clip them to rear panel clips.
4. Disconnect the water inlet hoses from the drain system...
User Guide - Page 33
... requirements. TROUBLESHOOTING
WASHER & COMPONENTS
ERROR CODES
When all four pedestal feet must be shown in the Estimated Time Remaining display (on some models).
• "Spin" and "Wash" (HT "Rinse" and "Cycle Complete") illuminated or "F20" on display (Water Inlet Problem-no water or insufficient water supply) Select PAUSE/CANCEL twice to washer clogged? These new sounds and pauses...
User Guide - Page 35
... 3 prong outlet? Replace the fuse, or reset the circuit breaker.
• Are both the hot and cold water faucets turned on the water.
• Is the water inlet hose kinked? Turn off the water and remove inlet hoses from the washer. Remove any accumulated film or particles. Reinstall hoses, turn on washer? Wash smaller loads.
• Is the washer door firmly...
User Guide - Page 36
... or Delicate cycle? The wash load must be trapped in the load if overloaded.
• Check the following: Was paper or tissue left in a load. Lint can occur when mixing whites and colors in pockets?
• Did you overloaded the washer? Use enough HE detergent to the dispenser? WASH / RINSE TEMPERATURE
• Are the hot and cold water inlet hoses reversed...
User Guide - Page 39
...™ Front-Loading Automatic Washer. COMPONENT LOCATIONS
Water Inlet Valve
Line Filter
Detergent Dispenser Motor & Assembly
Pressure Switch
Central Control Unit
Temperature Sensor (On Rear Of Tub) Heater (On Rear Of Tub) Basket Tub Assembly
Drive Motor
Front Interlock Switch
Not Shown: Console, Touchpad/LED Assembly, & Door Switch Assembly
Rear Interlock Switch ECO Valve Motor Control...
User Guide - Page 44
... right, and push it .
6. Replace all parts and panels before servicing. Water Inlet Valve
Pull Connector Out
Cold Water (Stripe)
Solenoid Terminal Holder
Water Inlet Valve
Inlet Hose & Clamp
5. Lift the locking tabs with a small-blade screwdriver (see page 4-2 for
the procedure). NOTE: The cold water wire connector has a black stripe on it into the washer off the water supply to do so...
User Guide - Page 80
... 40 minutes is broken or removed from door. Unplug washer or disconnect power. 2. Replace MCU board.
The pressure switch is running a Diagnostic Test or any cycle. Possible Causes/Procedure If there is out of range (23°F to 217°F [-5°C to it is water in the unit: - Make sure that the pressure switch hose is in the inlet valves. - Unplug washer...
User Guide - Page 81
... for proper shut off hot and cold water faucets and unplug the unit before servicing.
Plug in washer or reconnect power.
5.
Possible Causes/Procedure Door lock mechanism is not mounted upside down . NOTE: The door switch/lock unit can be to properly detect motor speed, the machine shuts down . DISPENSER SYSTEM ERROR
When the dispenser motor cannot...
User Guide - Page 82
....
Verify CCU operation by the pressure switch during the drain or spin phases, the washer will fill 4 liters of water and during 5 minutes the unit will rest without adding any
cycle. Check drain pump. 7. Run the unit through a RINSE/SPIN cycle. - Plug in washer or reconnect power. 6. Run a NORMAL cycle without tumbling, the water will be drained and it is...
User Guide - Page 83
... for 5 seconds.
• Next the washer begins the Diagnostic Test.
• To cancel out of service mode press PAUSE/CANCEL. (This exits you out of error codes. Entry modes:
• Universal mode across all the lights on the console will turn on. Close the door.
2. Upon release, all cycle LED lights will flash...
User Guide - Page 84
... Dispenser contact Cold water inlet valve
Dispenser motor Dispenser contact Hot Water inlet valve Pressure switch: Level_wash
Motor Motor Control (MCU)
Heater (if equipped) Motor Motor Control (MCU)
Heavy Duty Whitest Whites
Heavy Duty
Drain pump is set to CLEAN position.
Drain pump
Motor Motor Control (MCU)
6-6 Actuators to be displayed.
• If there is no error code to display...
User Guide - Page 85
... vated (80 minutes max.)
Drum executes reversing movement at wash speed (10 min).
This is set to maximum speed. Filling with both valves.
Stop motor to Main Wash compartment. MANUAL DIAGNOSTIC TEST
The washer must be empty and the control must be Checked
Door lock system
Dispenser Motor Dispenser contact Cold and Hot Water Inlet Valve Overfill level...
User Guide - Page 88
... immediately add 2/3 cup (160 mL) of washer interior.
Then repeat steps 1, 2 and 6 to cancel the failure code. a) If no items are in the washer.
The cycle will take approximately 3 minutes.
7.
NOTE: The basket will rotate, then the door will unlock, lock again, and then the cycle will continue.
• The machine will not fill, but the...
User Guide - Page 89
... a Diagnostic Test or
any cycle. Make sure water supply hoses are open.
2. Check operating pressure switch. 7. Verify flowmeter operation by looking for each problem.
1. Check wire harness connections. 4. Check the MCU by blowing air though the
part and measuring the resistance. 8. If no click, replace CCU.
3. Plug in washer or reconnect power. 6. Press...
Similar Questions
Kenmore He2 Model 110.47561600 F20 Error Code.
6 minutes into any cycle the washer stops filling and shows the F20 error code. After researching th...
6 minutes into any cycle the washer stops filling and shows the F20 error code. After researching th...
(Posted by riskoj 6 years ago)
How To Fix Kenmore He2t Error Code F24
(Posted by Frosscvbl 9 years ago)
My Kenmore He2t Keeps Giving Error Code F20 Only On Wash Cycle
Model 110.47561600 Works get on spin but nothing else till it wants to then it works fine again on a...
Model 110.47561600 Works get on spin but nothing else till it wants to then it works fine again on a...
(Posted by phodges85 10 years ago)
He5 Dryer Giving Me Error Code F21
Why is a dryer giving me a error code f21 and how do I fix it?
Why is a dryer giving me a error code f21 and how do I fix it?
(Posted by powersstevenp 10 years ago)
F20 Error Code On Kenmore Quiet Pack 4 He3t Steam
What does an F20 error code mean?
What does an F20 error code mean?
(Posted by mchapman 13 years ago)