Kenmore HE2t Support Question
Kenmore HE2t Support Question
Find answers below for this question about Kenmore HE2t - 3.7 cu. Ft. Front Load Washer.Need a Kenmore HE2t manual? We have 1 online manual for this item!
Question posted by Anonymous-154225 on September 10th, 2015
New Washer Dont Know How To Run It Can Someone Call Me Directly
The person who posted this question about this Kenmore product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by TechSupport101 on September 11th, 2015 3:26 AM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,285
Member since:
May 24th, 2013 Points: 12,171,285
The User Guide here https://www.helpowl.com/manuals/Kenmore/HE2t/27638 should offer the best guide. Otherwise, further assistance from Kenmore's Customer Service center can be requested video email or phone from here http://www.kenmore.com/en_us/customer-care.html
Related Kenmore HE2t Manual Pages
User Guide - Page 8
Max
Width Product Weight (approx)
WFW8300SW
WFW8500SW
WFW8500SR
Front Load Washer
Front Load Washer
Front Load Washer
White with Gray Accents
White with Gray Accents
White with Sterling Bright Accents
3.3
3.6
3.6... Water Consumption Average DOE (Gallons-Per-Cycle) Rated Load Load Pounds
Height Install Depth: Min - SPECIFICATIONS
Model Number Model Description
Color
Capacity (Cu.Ft.
User Guide - Page 13
...of electrical shock by a qualified electrician. GROUNDING INSTRUCTIONS
For a grounded, cord-connected washer:
This washer must be plugged into a grounded 3 prong outlet. In the event of the ...wiring system, or an equipment-grounding conductor must be run with the appliance - For a permanently connected washer:
This washer must be connected to the equipment-grounding terminal or lead...
User Guide - Page 14
... valves can result in back or other injury. NOTE: If the washer is to the water faucets
Make sure the washer drum is loose, move it is within approximately 3 ft (90 cm) of the inlet hoses.
CONNECT THE INLET HOSES
Insert new flat washers (supplied) into each of the unit is seated on coupling by...
User Guide - Page 15
...hose installation or replacement dates on the washer.
2. Cold water inlet
1. Laundry tub drain or standpipe drain
Connect the drain hose form to the washer
H
C
H.
Hot water inlet ...Damage to the washer's cold (C) water faucet.
Screw on the washer.
3. NOTE: Do not overtighten. Snap either end of the drain hose protects your floors from the shipping clips. Run water through both...
User Guide - Page 16
... in the standpipe. A
B
C
4.
NOTES:
• Do not force excess drain hose back into the rear of the laundry tub. Properly leveling your new washer.
Repeat this step until it contacts the floor. Then check that the washer is perfectly level (use a 17 mm open-end wrench to its final location. 6. When you are stable...
User Guide - Page 19
... period in all wash cycles except Rinse/Spin and Drain/Spin. You can handle slow speeds needed for a conventional washer. PRODUCT OPERATION
FEATURES AND BENEFITS
The front-loading high efficiency washer was designed to conserve resources and lower your new washer combines:
• 2 Springs to isolate vibration • 3 or 4 shock absorbers at the...
User Guide - Page 22
... the interior is clean before a new cycle can begin the wash cycle ...run it firmly until the lock clicks. It may also result in the washer. Use only HE High Efficiency detergent.
First Wash Cycle Without Laundry...laundry according to avoid spills. Do not overload washer. Load evenly.
• Wash small items such as it stops. The washer door will likely result in washer...
User Guide - Page 23
...is complete and the CYCLE COMPLETE light goes off. Do not put laundry additives directly into the wash tub. The package for this compartment for your laundry additives-one is for detergent, one is for the best performance. ... status light illuminates, the door unlocks, and the wash load can be removed from the washer. • When the wash cycle is complete, select PAUSE/CANCEL once.
8.
User Guide - Page 24
...Cycles and Options can add an additional item to your load.
• Always measure liquid chlorine bleach. To ...washer.
• Powdered detergent: Measure the amount of the new cycle. NOTE: Overfilling could cause an oversudsing condition. To drain the washer....
4. Select desired cycle.
3. Follow the manufacturer's directions for approximately 1 second). When the spin is complete,...
User Guide - Page 27
... the laundry, and a soaking time without spin assures gentle treatment, even for that you will hear sounds that option will be momentary pauses. The countdown to HIGH. Soak
Use the Soak cycle to avoid fabric stress. These new sounds and pauses are available with all options are part of your wash load. Delay...
User Guide - Page 30
Failure to do so will rotate while the washer runs a short sensing cycle. Open the dispenser drawer and immediately add 2/3 cup (160 mL) of bleach will cause product damage over time.
4. a) Mix a dilute solution, using a ...
User Guide - Page 31
...the outside of R.V.-type antifreeze in the drum.
2.
Wash the parts under running water.
To winterize washer:
1. 8.
Unlock the dispenser drawer by pressing the Release Lever.
Flush water... allow the cycle to keep it looking new. Because some water may stay in the dishwasher.
4. Run washer on both water faucets.
5.
Do not use washer again:
1. Remove the inserts (the ...
User Guide - Page 32
... must be properly set up for relocation by a certified technician. Reinstalling the washer
1. Use 1/2 the manufacturer's recommended amount for a medium sized load. Use only HE High Efficiency detergent. Do not reuse transport bolts. Run the washer through the Normal/ Casual cycle to follow these instructions can result in death, fi...
User Guide - Page 33
... removed? Are screens at equal heights.
• Is the washer gurgling or humming?
Re-select cycle and press START.
These new sounds and pauses are not accustomed to the pedestal and all cycle...ground prong.
The plywood may hear metal items touching the washer drum. As water is normal.
• Are you washing items with any new product, you will hear sounds that you may hear various...
User Guide - Page 34
...directly to avoid odors, see "Cleaning The Washer."
• Are you leave the door open to allow the washer to dry between uses. See "Washer Care" for details.
• Are the laundry additives in the washer. To freshen your washer and to the washer... in the fabric softener dispenser.
• Did you run the Clean Washer Cycle lately? Measure detergent and fabric softener. Dilute fabric...
User Guide - Page 35
...suds are removed. You will not affect cleaning performance.
3-17 Wash smaller loads.
• Is the washer door firmly shut? All four shipping bolts must be at least 30...new cycle. Add more frequently when a non-HE detergent is used.
• Is the load balanced? WASHER OPERATION
WASHER WON'T RUN, FILL, RINSE, OR TUMBLE; The door must be removed for 1 second? WASHER...
User Guide - Page 45
... the procedure). Replace all parts and panels before servicing.
Remove the top cover from the washer. Electrical Shock Hazard
Disconnect power before operating. Unplug washer or disconnect power. 2.
Turn the pressure switch 90° in a clockwise (CW) direction, and align the key on the switch with the slot in death or electrical shock...
User Guide - Page 47
c) Pull the washer away from the washer.
Align the strain relief key with the slot in the rear panel, and remove the cord from the wall far enough to access the power supply cord on the power supply cord 90° in either direction. Power Supply Cord Strain Relief
4-9 d) Use a pair of pliers and turn the strain relief on the rear panel.
User Guide - Page 80
...Causes/Procedure A power glitch may cause this
model. (abnormal = infinity) 4.
Plug in washer or reconnect power
7.
Check for 3 minutes before unlocking the door.
3. The machine ... not working properly. Possible Causes/Procedure Door lock mechanism is running. 4. Unplug washer or disconnect power. 2. Unplug washer or disconnect power. 2.
If the above does not correct ...
User Guide - Page 81
... mechanism is detected inside the drum. Possible Causes/Procedure 1. Verify CCU operation by running a Diagnostic Test or any worn or failed components.
4. Reference Status LEDs chart,...Check for foreign objects. 2. Unplug washer or disconnect power. 3. Plug in washer or reconnect power.
5. Possible Causes/Procedure 1. LOAD INSIDE DRUM DURING CLEANING WASHER CYCLE
If at the MCU is ...
Similar Questions
No Cold Water
I have a Kenmore 2982 - 800 4.0 cu. Ft. Capacity top-load Washer bought in 2009. All of a sudden, it...
I have a Kenmore 2982 - 800 4.0 cu. Ft. Capacity top-load Washer bought in 2009. All of a sudden, it...
(Posted by jethalhuber 10 months ago)
F1 Code On Washer; What Does It Mean?
Not draining and posibally not spinning correctly.
Not draining and posibally not spinning correctly.
(Posted by mannbuilder65 9 years ago)
How Can I Clean My Kennmore Washer Machine?
(Posted by Mariavargas1102 9 years ago)
Please Direct Me To Kenmore Elite He5 Steam Laundry Washer Manual.
(Posted by vigasc 10 years ago)