Kenmore 8804 Support Question
Kenmore 8804 Support Question
Find answers below for this question about Kenmore 8804 - 5.8 cu. Ft. Electric Dryer.Need a Kenmore 8804 manual? We have 2 online manuals for this item!
Question posted by downit on October 27th, 2012
Our Dryer Is Starting To Squeak When We Turn It On
I wonder if the belt is going?
Current Answers
Related Kenmore 8804 Manual Pages
Use and Care Guide - Page 2
...propertydamage or damage to tlne washer. Use tlne dryer only as instructed in tlne vicinity of injury, and tell you how to light any electrical switch;
WHATTODOIFYOUSMELL GAS:
• Do not try...the information in the Use and Care Guide, Operating Instructions, Installation Instructions and on the dryer serial plate located of the left side of all occupants. You can be performed by...
Use and Care Guide - Page 3
... an adaptor plug or extension cord or remove grounding prong from this way ONL Y
Important Safety Instructions Con't
_Avoid
fire hazard or electrical shock. Keep laundry products out of the dryer. You can be practiced when installing, operating and maintaining any time. Prevent Fire
Do not dry items that may melt or burn...
Use and Care Guide - Page 4
...automatically turns off the motor in the unlikely event of fire, electrical shock, or injury to persons, read and follow fabric care labels and laundry product labels.
ALWAYS disconnect the dryer ...features desired.
Items need room totumble
freely for drying. Press START to a gas pipe. specifically recommended in the dryer for even drying. Prepare items for even drying and less ...
Use and Care Guide - Page 5
... Cleaning
Clean lint screen after every load. Hazardous fumes or electrical shock could enter the exhaust system and cause damage to the dryer. The screen is located at the end of the cycle ...at the bottom of the door opening.
Closing the door turns off the light. A clothes dryer produces combustible lint. Regularly inspect the outdoor exhaust opening and remove any type spray...
Use and Care Guide - Page 6
... cup (120 ml) in
place.
Turn items inside out to abrasion from normal
...dryer drum becomes stained from tape or labels with a mixture of lint build-up and cling to
electricity. These areas can damage the finish or controls.
reduce static electricity....
Shrinking
Overdrying. Remove cleanser residue before starting the dryer. Outside Clean the cabinet with a damp...
Use and Care Guide - Page 7
...outsideofthedryerfeelstoo hot or smells hot.
Electric dryer is empty or there has...belt buckles, zippers and fasteners may save both time and expense.
Insufficient sorting of the drum.
Follow fabric care label instructions.
Permanently attached items such as cycle ends.
Always remove foreign objects from drum and restart dryer. Remove objects from pockets before starting...
Use and Care Guide - Page 8
...for any non-covered repair service and related installed parts.
Power surge protection against electrical damage due to instruct the user in the U.S.A.
for a particular purpose, are...this appliance fails due to a defect in the Agreement:
Parts and labor needed to filters, belts, light bulbs, and bags. 2.
limitation of more product failures occur within one year or...
Installation Instructions - Page 2
... and ordinances and the latest edition of the National Fuel Gas Code ANSI Z223.1, or in Canada, the Canadian electrical code C22.1 part 1. Phillips head screwdriver.
2. Flat or straight blade screwdriver.
5.
This Dryer is installed correctly and safely. If you cannot reach your gas supplier, call your building.
.
Do not touch any...
Installation Instructions - Page 3
... into the laundry area. maximum time delay fuse or circuit breaker. The dryer must be located so the power supply cord is accessible when the dryer is made up...NEMA 14-30R GAS Dryer
CIRCUIT-
The dryer is installed on the same circuit.
ELECTRICAL REQUIREMENTS
i
ELECTRICDryer
CIRCUIT- Individual I 5 amp. POWER SUPPLY CORD -
A clothes dryer produces
combustible lint....
Installation Instructions - Page 4
...Turns
(10.2 cm) 60 ft.(18.28 m)
52ft.(IS.84m)
44 ft.113.41 m)
32 ft.(9.zsm)
2 _/2'_. (6.35 cm) 48 ft.114.63 m)
40 ft.(12.19 In) 32ft. 19.75m)
24ft. {7.31m)
28 ft... and start the dryer.
3. The more often you should be used. • Venting vertical through your dryer to... the manometer reading is acceptable. However, on electric dryers, exhausting can accumulate lint, resulting in the absence...
Installation Instructions - Page 5
... system during any pressure testing of the door is acceptable.
On carpet. A dryer installed in a recess or closet installation.
MINIMUM INSTALLATION CLEARANCES - The following illustrations...) N.P.T.plugged tapping, accessible for proper ventilation. Air openings are required to the dryer.
6.
The dryer MUST be exhausted outdoors.
5. In an area exposed to or less than 1/2...
Installation Instructions - Page 6
Dryer Installation Dimensions
Free=Standing & Under Counter
48.5" To clear open door (123.19cm)
Electrical supply
on rear of unit
/
0 o ,'_,_ #
l
Gas supply pipe
\ on rear of ...) 27.75 to clear knobs (70.49cm) 28.5 to clear door handle (72.39cm)
q
(68.58cm)
(34.29cm)
Stacked Dryer Installation Dimensions
T
9
(68.58cm) 27.0"
1
28.25" to clear open door (124.46cm)
72.00"
(11.12cm) (...
Installation Instructions - Page 7
...mobile home structure.
3.
Metal ducting must be exhausted outside make up or move the dryer.
2. If dryer is exhausted through the floor and area beneath the mobile home isenclosed, the exhaust ... 24 CFR-Part 32-80) or when such standard is not applicable, with no obstructions. The dryer is preferred.
2. CAN/CSA C22.2 (latest editions) for outside (outdoors, not beneath the mobile...
Installation Instructions - Page 8
... hinges. Figure 4 5. Figure 5 6. Place door on a towel or pad handle side down to prevent any possible scratches to the front panel. (Figure 2) For best results, start by only removing one screw per hinge.
Remove two (2) door handle screws and two (2) hole plugs from door assembley. (Figure 5)
Figure 3 3. Remove all . Window Door...
Installation Instructions - Page 9
... .
Grasping firmly the top of the retention tabs and pull lens away from the transition ring. (Figure 8)
Figure 11 12. Once the first screw is started, attach the second screw to inner door assembly. (Figure 11)
13. Install four (4) plugs into holes that had secured the hinge.
15. Reassembly outer door...
Installation Instructions - Page 10
.... Check with a power supply cord having an equipment-grounding conductor and a grounding plug, the plug must be run with a three-prong (grounding) plug for electrical current.
2. If your dryer.
A U.L. Do not modify plug provided with all local codes and ordinances. A chemical reaction occurs between copper and aluminum and can result in a risk...
Installation Instructions - Page 11
... at connections.
6. WIRE SYSTEM
USA ELECTR/CDryer
l
1. Install a U.L approved strain relief in U.S.A. Remove the ground wire from the dryer harness to the back of the dryer upper corner.
2. GREEN SCREW
GREEN POWER...of the mounting bracket. Tighten the strain relief nut securely so the strain relief does not turn .
9.
power cord, NEMA 10-30 type SRDT,through the strain relief.
4. Tighten...
Installation Instructions - Page 12
...). Testall connections by a qualified gas technician.
2. If replacement parts are not meant to be used when elevating the dryer for future reference.
With the dryer in a garbage container or make sure the
dryer area is turned on a soapy water solution. The instructions in this manual and all materials in its final position, adjust one...
Installation Instructions - Page 24
For Sears professional installation of home appliances and items like vacuums, lawn equipment, and electronics, call or go on a product serviced by Sears:
1-800-827-6655 (U.S.A.)
1-800-361-6665 (Canada)
Para pedir servicio de reparaci6n a domicilio, y para ordenar piezas:
1-888-SU-HOGAR ®
(1-...
Similar Questions
Kenmore He2 Gas Dryer Start Button Not Working
How to fix? How can I remove the control panel?
How to fix? How can I remove the control panel?
(Posted by godmothermarci 10 years ago)
I Have A Kenmore 600 Series Dryer And I Am Going From A 4 Prond Cord To A 3 Pron
do i need to attach a 10g wire from ground screw to center white neutral wire
do i need to attach a 10g wire from ground screw to center white neutral wire
(Posted by dentonkola 11 years ago)
New Dryer Has No Heat. Runs Cold Then I Can Smell Gas Coming Out Of Vent
(Posted by piepergeorge 12 years ago)
Kenmore 80272 Dryer Question
We are looking at this dryer, but I am concerned because I use "air dry" alot, so I am wondering......
We are looking at this dryer, but I am concerned because I use "air dry" alot, so I am wondering......
(Posted by jwhall15 12 years ago)