Kenmore 4810 Support Question
Kenmore 4810 Support Question
Find answers below for this question about Kenmore 4810 - 3.5 cu. Ft. I.E.C. High-Efficiency Washer.Need a Kenmore 4810 manual? We have 2 online manuals for this item!
Question posted by tbyerly2 on April 2nd, 2013
Fast Spin Doesn't Spin
on the final fast spin my washer is not spinning the water out of my clothes
Current Answers
Related Kenmore 4810 Manual Pages
Operating Instructions - Page 1
... label instructions on items to the detergent compartment. Add laundry load to the appropriate compartments.
,, Slowly close door and...final spin. FOR BEST RESULTSAHIGH EFFICIENCY /_"_em_'__,
_G
WASHERS MUST BE USED.
(q_..._'
" if desired, add liquid chlorine bleach and liquid fabric softener to the wash drum.
5.
Hot water is a result of siphoning action and part of a high efficiency...
Operating Instructions - Page 2
... followed by 3 rinses and a slow final spin. Add the fabric softener to the load. Wash / Rinse Water Temperatures
Select the wash and rinse water temperatures appropriate for a cycle, it will not be displayed during off peak energy hours.
For example, High Speed in the washer. To change the final spin speed, press SPIN until the Control _ (Control Lock) lights...
Operating Instructions - Page 3
...
,/
Heavy Soil/Stain
,/
,/
,/
Extra Rinse
,/
,/
,/
,/
,/
,/
,/
,/
Extra Spin
,/
,/
,/
Delay Start
,/
,/
,/
,/
,/
,/
,/
,/
,/
,/
,/
,/
* Factory Settings
,/ Available settings
** Estimated cycle duration is based on factory settings and does not
include water fill times, out-of-balance or oversudsing corrections. WASHER SETTINGS CHART
The following chart shows the...
Installation Instructions - Page 1
... your gas supplier, call your gas supplier from a neighbor's phone. Contents
S UBJECT Pre-lnstallation Requirements Electrical Requirements Grounding Requirements Water Supply Requirements Drain Requirements Rough-In Dimensions Location Of Your Washer Unpacking Installation Replacement Parts
PAGE
2 2 2 2 2 3 4 4-5 5-6 6
Installation and service must be followed to minimize the risk of fire or...
Installation Instructions - Page 2
...with the National Electrical Codes, ANSI/NFPA 70 (latest edition). Since your water pressure. Phillips screwdriver 2. 10 mm socketwith ratchet.
3. Channel-lock adjustable pliers... to be grounded.
DRAIN REQUIREMENTS
I /4 in . (229 cm) high standpipe.
For higher standpipe, use of this washer with a power supply cord having an equipment-grounding conductor and a grounding...
Installation Instructions - Page 4
... carpet. Using a rug, blanket or piece of cardboard to dripping water or outside weather conditions. To ensure vibration or movement does not occur... or stored (including automobiles).
4. Remove and save the styrofoam base and shipping plug.
LOCATION OF YOUR WASHER DO NOT INSTALL YOUR WASHER: I in. (2.54 cm) Closet door ventilation required: 2 Iouvered openings each 60 in2(387 cm2),...
Installation Instructions - Page 5
... the hot and cold faucets to flush the water lines and remove particles that might clog up the water valve screens.
For free standinq installation and with the washer in it's final position, place a level on and check for leaks.
Adjust the appropriate leg so the washer is level front-to-rear and side-to...
Installation Instructions - Page 6
...washer for future reference. iNSTALLATiON (CON'T)
5. Plug the power cord into an outlet.
8. l
NOTE: A wiring diagram and technical data sheet are not meant to the standpipe, inlet hose, laundry...use .
Placethese instructions in the drain
opening. Place the hook end of the water.
7. Run the washer through a complete cycle. If your Owner's Guide before plugging the power cord into...
Similar Questions
Washer Capacity
Hi,What is the cubic capacity of a kenmore 110.29822801
Hi,What is the cubic capacity of a kenmore 110.29822801
(Posted by juliettemallen 5 years ago)
How Can I Clean My Kennmore Washer Machine?
(Posted by Mariavargas1102 9 years ago)