Hunter 90064 Support Question
Hunter 90064 Support Question
Find answers below for this question about Hunter 90064.Need a Hunter 90064 manual? We have 1 online manual for this item!
Question posted by Lineyrich on April 13th, 2019
I Got The Glass To Clean Out The Dust Now I Can’t Get It Reinstalled. How To?
plastic bearing pieces don't fit thru slot in stamped flange
Current Answers
Related Hunter 90064 Manual Pages
Owner's Manual - Page 1
Owner's Manual
Model
90063/90064
1
41722-01 09/09/2011 Ellipse
Bath Ventilator with Light and Night Light
English
Español
Página 21
41722-01 20110909 ©2011 Hunter Fan Co.
Owner's Manual - Page 2
... in a wall. Before servicing or cleaning the unit, switch power off power unit.
3. When the service disconnecting means cannot be installed in ceilings up rear motor plate tab while pushing out on accidentally. When cutting or drilling into the slot in accordance with the exact service motor. Ducted fans must point upward.
4. Never...
Owner's Manual - Page 6
... under
the wiring cover plate.
6
41722-01 09/09/2011
Tighten the wiring cover plate screw. A14
Fan Motor Night Light
Light
Black 2 Pin
White
White Red Night Light 3 Pin Black Light
*Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In)
White
Red Switch 1 (AC In...
Owner's Manual - Page 7
... from the motor to the outside. A017
A18
H
Connect 4" duct and vent to the wiring cover plate. A20
H
I
Reinstall the motor by tightening the 2 screws.
Test the motor. If ducting does not fit securely, an adapter may need
to be purchased.
If the motor does not run, check the plug connection.
7
41722...
Owner's Manual - Page 9
... screws, leaving space between the screw head and the joist.
Pull wires through the strain relief. B19
Fan Motor Night Light
Light
Black 2 Pin
White
White Red Night Light 3 Pin Black Light
*Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In)
White
Red Switch 1 (AC In...
Owner's Manual - Page 10
B23
H
Connect 4" duct and vent to the wiring cover plate. B25
H I
Reinstall the motor by tightening the 2 screws.
41722-01 09/09/2011 B24
Connect wiring from the motor to ...up into position.
Tape joints.
B22
B21
G•
Tighten the wiring cover plate screw. If ducting does not fit securely, an adapter may need
to be purchased. B20
F
2
1
F
Install the wiring cover plate.
Owner's Manual - Page 11
... to accommodate the new
motor housing (9"x 9.75"). B26
Turn on page 18 to attach grille. Existing Construction - accessible from above
C11 EXISTING FAN
NO EXISTING FAN
OR
Remove an existing fan and check to make sure the opening is large enough to mark position.
11
41722-01 09/09/2011 If the motor...
Owner's Manual - Page 13
C21
Pull wires through the strain relief. If ducting does not fit securely, an adapter may need to the outside. C20
Connect 4" duct and vent to be purchased. Tighten the strain relief screws.
13
41722-01 09/09/2011
C19
Tighten screws. Tape joints.
C17
C18
Attach the rails onto the screws.
Owner's Manual - Page 14
... pinched
14
between the motor and the housing.
41722-01 09/09/2011 C25
C24
G•
Tighten the wiring cover plate screw. Reinstall the motor by inserting the tabs and pushing up into
position.
C22
Fan Motor Night Light
Light
Black 2 Pin
White
3 Pin
White Red Night Light
Black Light *Option
*Option...
Owner's Manual - Page 15
... into position above the ceiling
41722-01 09/09/2011
C27
C28
I
Secure the motor by tightening the 2 screws. accessible only from below
D11 EXISTING FAN
D12
E
Remove an existing fan and check to make sure the opening is large enough to attach grille.
Owner's Manual - Page 16
If ducting does not fit securely,
an adapter may need to duct connector. E
Screw pre-loaded screws into joist or framing.
D16
Fan Motor Night Light
Light
Black 2 Pin
White
White Red Night Light 3 Pin Black Light
*Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In)
White
Red...
Owner's Manual - Page 17
... plate. Make sure all wiring connections are not pinched between the
motor and the housing. D19
D18
G•
Tighten the wiring cover plate screw. D21
H
Reinstall the motor by tightening the 2 screws.
17
41722-01 09/09/2011
Turn on the power source.
Make sure the wires are inside the box...
Owner's Manual - Page 18
... shown, and screw into place.
18
41722-01 09/09/2011
E3
E4
H
J L
Connect wiring harness.
Attaching the Grille
E1
H M
Remove the thumbscrews. E2
N
Remove glass. If the motor does not run, check the plug connection.
Owner's Manual - Page 19
...Not Included) and 1 Max 7 Watt C-7 bulb (Not Included).
N
Align glass and push up. Trouble Shooting
Problem: Fan does not come on , replace fuse, or reset breaker. • Check all fasteners.
•...; C heck the glass to make sure it is noisy.
To
confirm that the fan is running, place your hand near the vents to feel the air movement...
Owner's Manual - Page 20
... EXPRESS WARRANTIES.
NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS MADE IN RESPECT OF GLASS FIXTURES OR LIGHT BULBS OR THE FINISH ON ANY METAL PORTION OF THE BATH EXHAUST FAN. We will be responsible for all parts and labor costs for repairs on all...
Similar Questions
How Do I Remove The Cover To Replace The Bulb On The Hunter 90064
(Posted by cmterra29 3 years ago)
Bulb Replacement On A 90064
how do you get to the bulbs on a 90064 fan/light combo
how do you get to the bulbs on a 90064 fan/light combo
(Posted by ccdunn318 3 years ago)
Replacement Glass For Hunter 90064
where can I purchase the replacement glad for the Hunter 90064 Exhaust Fan Light unit
where can I purchase the replacement glad for the Hunter 90064 Exhaust Fan Light unit
(Posted by Jwaller0717 7 years ago)
Why Am I Unable To Remove Glass Cover To Replace Bulbs?
Have been trying to remove the glass cover on my Hunter 82023 to replace bulbs for some time now. Fi...
Have been trying to remove the glass cover on my Hunter 82023 to replace bulbs for some time now. Fi...
(Posted by maroney914 8 years ago)