Hunter 90064 Support Question
Hunter 90064 Support Question
Find answers below for this question about Hunter 90064.Need a Hunter 90064 manual? We have 1 online manual for this item!
Question posted by palter on November 21st, 2020
How Do I Remove Glass To Change Bulb
The person who posted this question about this Hunter product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by INIMITABLE on November 21st, 2020 9:00 AM
INIMITABLE
Member since:
April 3rd, 2020 Points: 2,071,730
Member since:
April 3rd, 2020 Points: 2,071,730
Click here and follow the instructions.
I hope this is helpful? PLEASE "ACCEPT" and mark it "HELPFUL" to complement my little effort. Hope to bring you more detailed answers
-INIMITABLE
Related Hunter 90064 Manual Pages
Owner's Manual - Page 1
Owner's Manual
Model
90063/90064
1
41722-01 09/09/2011
Ellipse
Bath Ventilator with Light and Night Light
English
Español
Página 21
41722-01 20110909 ©2011 Hunter Fan Co.
Owner's Manual - Page 2
...SUPPLY AND LOCK OUT
SERVICE PANEL BEFORE SERVICING UNIT
PREVENTATIVE MAINTENANCE
A clean fan provides better service. To remove motor plate, find the single tab on the side of housing. If... safety standards,such as listed below. When cutting or drilling into the slot in a wall. Ducted fans must point upward.
4. Never place a switch where it must be marked as dishwashing liquid, and ...
Owner's Manual - Page 3
....
3
41722-01 09/09/2011
Loosen screws. Before Installation
1
30
20
O FF
O FF
Tools Needed. (Not supplied) Estimated assembly time: 30 to 60 minutes
NOTE: Remove all the parts.
If damaged, call 1-888-830-1326 for replacements. Not Included.
Check all packing materials before installation.
2
I 74508-03-133 J 77520-01 K 65219...
Owner's Manual - Page 4
3
4
H
E
Remove the motor/blower from the housing.
5
Remove packing material.
6
Remove the pre-loaded screw tip covers.
7 G
Back out the pre-loaded screw tips until flush with the side of the housing.
8
F
Remove the wiring cover screw.
4
41722-01 09/09/2011
Remove the wiring cover.
Owner's Manual - Page 6
... Night Light
Light
Black 2 Pin
White
White Red Night Light 3 Pin Black Light
*Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In)
White
Red Switch 1 (AC In) Black Switch 2 (AC In)
Connect wires as shown. ...
Owner's Manual - Page 9
... screws, leaving space between the screw head and the joist. Pull wires through the strain relief. B19
Fan Motor Night Light
Light
Black 2 Pin
White
White Red Night Light 3 Pin Black Light
*Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In)
White
Red Switch 1 (AC In...
Owner's Manual - Page 11
... housing (9"x 9.75"). B28 Go to step E1
on the power source. B27
ON
OFF
Test the motor.
accessible from above
C11 EXISTING FAN
NO EXISTING FAN
OR
Remove an existing fan and check to make sure the opening is large enough to mark position.
11
41722-01 09/09/2011 B26
Turn on page...
Owner's Manual - Page 14
... plate screw.
Make sure the wires are inside the box or under
the wiring cover plate. C22
Fan Motor Night Light
Light
Black 2 Pin
White
3 Pin
White Red Night Light
Black Light *Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In)
White
Red Switch 1 (AC In...
Owner's Manual - Page 15
accessible only from below
D11 EXISTING FAN
D12
E
Remove an existing fan and check to make sure the opening is large enough to attach grille. Test the motor.
Turn on page 18
to accommodate the new
motor ...
Owner's Manual - Page 16
...
2 1
Attach existing ducting to be purchased. Tape joints. E
Screw pre-loaded screws into joist or framing. D16
Fan Motor Night Light
Light
Black 2 Pin
White
White Red Night Light 3 Pin Black Light
*Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In)
White
Red Switch 1 (AC In...
Owner's Manual - Page 18
DO NOT ALLOW THE FIXTURE TO HANG FROM THE WIRING HARNESS.
Attaching the Grille
E1
H M
Remove the thumbscrews.
E2
N
Remove glass. E3
E4
H
J L
Connect wiring harness.
Position the strain relief bracket between the plugs as shown, and screw into place.
18
41722-01 09/09/2011 ...
Owner's Manual - Page 19
N
Align glass and push up.
Problem: Fan is secure. • C heck the flapper to make sure it matches the
wiring diagram.
Solution: • R eplace the light bulb with a new bulb. • T urn power on , replace fuse, or reset breaker. • Check all 4
thumbscrews MUST be properly installed. If you need parts or service assistance, please...
Owner's Manual - Page 20
... FITNESS FOR A PARTICULAR PURPOSE, IS MADE IN RESPECT OF GLASS FIXTURES OR LIGHT BULBS OR THE FINISH ON ANY METAL PORTION OF THE BATH EXHAUST FAN.
If we authorize you to ship it to us, you...original user or consumer purchaser of this Hunter bath exhaust fan:
If any part of your Hunter bath exhaust fan (except for glass fixtures and light bulbs) fails at any time within five years after the ...
Similar Questions
How Do I Remove The Cover To Replace The Bulb On The Hunter 90064
(Posted by cmterra29 3 years ago)
Why Am I Unable To Remove Glass Cover To Replace Bulbs?
Have been trying to remove the glass cover on my Hunter 82023 to replace bulbs for some time now. Fi...
Have been trying to remove the glass cover on my Hunter 82023 to replace bulbs for some time now. Fi...
(Posted by maroney914 8 years ago)
