Hunter 90052 Support Question
Hunter 90052 Support Question
Find answers below for this question about Hunter 90052.Need a Hunter 90052 manual? We have 2 online manuals for this item!
Question posted by mkish on June 13th, 2014
Vent Adapter
I am looking to purchase the adapter to go from the housing to the vent hose?
Current Answers
Related Hunter 90052 Manual Pages
Owner's Manual - Page 1
Installation Guide
ENGLISH
See page 2
Español
Vea la página 21
90052/90053/90054/90058 Saturn™ Bath Ventilator with Light
READ and SAVE THESE INSTRUCTIONS
028_41718_EngS_1.28.08_Arial.indd 1
1
41718-01 01/28/2008
1/28/08 10:47:06 AM
Owner's Manual - Page 2
Never place a switch where it must be vented to the outdoors.
7. Install fan at the same time. Do not use abrasive cloths, steel wool pads or scouring powders. Please read specification label on the side of the housing or insert a screwdriver into wall(s) or ceiling, do not damage electrical wiring or other hidden utilities...
Owner's Manual - Page 4
3
4
H
E
Remove the motor/blower from the housing.
5
Remove packing material.
6
Remove the pre-loaded screw tip covers.
7
G
Back out the pre-loaded screw tips until flush with the side of the housing.
8
F
Remove the wiring cover screw.
4
41718-01 01/28/2008
028_41718_EngS_1.28.08_Arial.indd 4
Remove the wiring cover.
1/28/08 10:47:11 AM
Owner's Manual - Page 5
... into joist or framing.
5
41718-01 01/28/2008
028_41718_EngS_1.28.08_Arial.indd 5
1/28/08 10:47:13 AM
Screw pre-loaded screws into the housing and secure with the washer. attaching to joist go to step A11, page 5 For New Construction - attaching to step C11, page 11 For Existing Construction...
Owner's Manual - Page 6
...cover plate.
If ducting does not fit securely, an adapter may need
to the outside. Connect 4" duct and vent to be purchased.
6
41718-01 01/28/2008
028_41718_EngS_1.28.08_Arial....indd 6
1/28/08 10:47:15 AM Make sure all wiring connections are inside the box or under
the wiring cover plate. Tape joints.
A14
Fan...
Owner's Manual - Page 7
... grille.
A21
ON
A22
Go to the wiring cover plate. Test the motor. Make sure the wires are not pinched between the motor and the housing. A17 0
A18 0
Connect wiring from the motor to step
E1
OFF
on the power source.
Owner's Manual - Page 9
...*Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In)
White
Black Switch 2 (AC In)
Connect wires as shown. Connect 4" duct and vent to be purchased.
9
41718-01... 01/28/2008
028_41718_EngS_1.28.08_Arial.indd 9
1/28/08 10:47:24 AM Tape joints.
If ducting does not fit securely, an adapter may need
...
Owner's Manual - Page 10
.../28/2008
028_41718_EngS_1.28.08_Arial.indd 10
1/28/08 10:47:27 AM
Make sure the wires are not pinched between the motor and the housing. B26
ON
B27
Go to step
E1
OFF
on the power source. Test the motor. B22
B23
H H
Connect wiring from the motor to attach grille...
Owner's Manual - Page 11
... using holes as a template to mark position. Mark position of your sheetrock. accessible from above
C11 EXISTING FAN
NO EXISTING FAN
OR
Remove an existing fan and check to accommodate the new
motor housing (8"x 8.5").
8"
8.5"
Use the motor housing as a template.
11
41718-01 01/28/2008
028_41718_EngS_1.28.08_Arial.indd 11
1/28/08 10:47...
Owner's Manual - Page 12
... screw head and the joist. Screws are not provided. C19
Tighten screws. If ducting does not fit securely, an adapter may need to the outside.
C20
Connect 4" duct and vent to be purchased.
12
41718-01 01/28/2008
Pull wires through the strain relief.
028_41718_EngS_1.28.08_Arial.indd 12
1/28/08 10...
Owner's Manual - Page 13
...
1/28/08 10:47:35 AM C23
C24
F
H
G
Install the wiring cover plate. C21
Tighten the strain relief screws. C22
Fan Motor Light
Black 2 Pin
White
White
3 Pin Black Light *Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In)
White
Black Switch 2 (AC In)
Connect wires...
Owner's Manual - Page 14
... 14
14
41718-01 01/28/2008
1/28/08 10:47:38 AM Make sure the wires are not pinched between the motor and the housing. I
Secure the motor by inserting the tabs and pushing up into position.
Owner's Manual - Page 15
... wires through strain relief.
If ducting does not fit securely,
an adapter may need to accommodate the new
motor housing (8"x 8.5"). accessible only from below
D11 EXISTING FAN
D12
E
Remove an existing fan and check to make sure the opening is large enough to be purchased. D15
Attach existing ducting to duct connector.
D13
Move the...
Owner's Manual - Page 16
...:43 AM Make sure all wiring connections are not pinched between the
motor and the housing.
16
Secure the motor by inserting the tabs and pushing up into position.
Make ...D19
H
Connect wiring from the motor to the wiring cover plate.
D16
Fan Motor Light
2 Pin
Black White
White
3 Pin Black Light *Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1...
Owner's Manual - Page 18
... (Not Included).
41718-01 01/28/2008
028_41718_EngS_1.28.08_Arial.indd 18
1/28/08 10:47:48 AM E7
Align posts A, B, C and D (stamped into motor housing) with posts A, B, C and D (stamped into light fixture). Reinstall the strain relief bracket screw.
WARNING: To reduce the risk of the motor. E5
Position the strain...
Owner's Manual - Page 19
... 19
19
41718-01 01/28/2008
1/28/08 10:47:49 AM Screw glass dome into position. To confirm that the fan is running, place your hand near the vents to make sure it matches the wiring diagram.
Problem: Light does not come on , replace fuse, or reset breaker. • Check...
Owner's Manual - Page 20
...you will be responsible for all parts of the bath exhaust fan. IF THE ORIGINAL USER OR CONSUMER PURCHASER CEASES TO OWN THE FAN, THIS WARRANTY AND ANY IMPLIED WARRANTY WHICH THEN REMAINS IN ...GLASS FIXTURES OR LIGHT BULBS OR THE FINISH ON ANY METAL PORTION OF THE BATH EXHAUST FAN.
The purchaser must present the sales receipt or other transportation charges to our factory or service center....
Similar Questions
Am Looking To Buy Fan Blades For Hunter Ceiling Fan Model 21318 Part Number 7669
(Posted by Dccantwell 1 year ago)
Pull Chain For 3 Speed Fan Is Broken Off Inside The Housing. I Have Removed Glo
I have remove globe and do not see access to speed, on off device. Do I need to remove led light? Do...
I have remove globe and do not see access to speed, on off device. Do I need to remove led light? Do...
(Posted by Lowerymsmith 5 years ago)
Light On Hunter 21323 Very Dim
The LED light on a Hunter fan that is in my new house is very dim. So dim that it would only serve a...
The LED light on a Hunter fan that is in my new house is very dim. So dim that it would only serve a...
(Posted by atbwdb 6 years ago)
Where Can I Purchase Rubber Grommets For My Hunter Fan?
(Posted by bobwinton 10 years ago)
Where Can I Purchase A Replacement Glass Bowl For My Hunter Ceiling Fan #45055
(Posted by deansaludes 11 years ago)