Hunter 83001 Support Question

Find answers below for this question about Hunter 83001.
Need a Hunter 83001 manual? We have 1 online manual for this item!

Hunter Overview Questions Manuals Reviews Videos Research

Question posted by Janwhite1122 on October 16th, 2023

#83001 Riazzi Bath Ventilator With Light

can glass plate be replaced

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by Technicalproblemsolver on October 16th, 2023 2:35 PM

This answer was accepted by the poster of the original question.

Technicalproblemsolver

Member since:
September 25th, 2023

Points: 190,500

1,100
points

Yes, the glass plate on the Hunter 83001 Riazzi Bath Ventilator with Light can be replaced. If the glass plate is broken or damaged, you can purchase a replacement glass plate from the manufacturer or from authorized retailers that sell Hunter replacement parts. To replace the glass plate, follow these steps:

1. Turn off the power to the bath ventilator and light at the circuit breaker or fuse box.

2. Carefully remove any screws or fasteners holding the existing glass plate in place. Be sure to support the glass plate to prevent it from falling or breaking further.

3. Once the glass plate is removed, clean the area if needed and ensure there are no remaining glass fragments or debris.

4. Install the new glass plate by aligning it with the mounting holes and securing it using screws or fasteners provided.

5. Make sure the glass plate is securely attached before restoring power to the bath ventilator and light.

6. Test the bath ventilator and light to ensure they are functioning properly with the new glass plate.

It is always a good idea to consult the product manual or contact Hunter customer support for specific instructions or if you have any further questions or concerns regarding the replacement of the glass plate on your Hunter 83001 Riazzi Bath Ventilator with Light.

"Hi there,

I hope my response was helpful in addressing your question or concern. If you found it valuable, I kindly ask you to consider accepting my answer by clicking the designated button. Your support will not only acknowledge my efforts but also guide others in finding useful solutions. Thank you for your trust and I'm ready to assist you further if needed.

Best regards,
Technicalproblemsolver"

Answer #2: Posted by SonuKumar on October 16th, 2023 8:18 PM

SonuKumar

Member since:
May 9th, 2021

Points: 16,621,300

100
points

Yes, the glass plate on the Hunter 83001 Riazzi Bath Ventilator With Light can be replaced. To do this, you will need to remove the old glass plate and install the new one.

Here are the steps to remove the old glass plate:

Turn off the power to the bath ventilator at the breaker box.

Remove the screws that attach the glass plate to the housing.

Carefully remove the glass plate.

Here are the steps to install the new glass plate:

Carefully position the new glass plate on the housing.

Secure the glass plate with the screws that you removed in step 2.

Turn the power back on to the bath ventilator at the breaker box.

You can purchase a replacement glass plate for the Hunter 83001 Riazzi Bath Ventilator With Light from Hunter or from most home improvement retailers.

Here are some additional tips for replacing the glass plate on your Hunter 83001 Riazzi Bath Ventilator With Light:

Be careful not to overtighten the screws, as this could damage the glass plate.

If the glass plate is broken, wear gloves to avoid cuts.

Dispose of the old glass plate properly.

Clean the housing of the bath ventilator before installing the new glass plate.

If you are not comfortable replacing the glass plate yourself, you can contact a qualified electrician or HVAC technician for assistance.

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.

Regards,
Sonu
Your search handyman for all e-support needs!!

Related Hunter 83001 Manual Pages

Owner's Manual - Page 2

... must be connected to a value greater than R40. For general ventilating use abrasive cloths, steel wool pads or scouring powders. DO NOT... exact service motor. DO NOT use only. To remove motor plate, find the single tab on accidentally. METAL AND ELECTRICAL PARTS ...clean the fan as dishwashing liquid, and a soft cloth. You should replace the impeller at least 5 feet (1.52 m) above ...

Owner's Manual - Page 3

If damaged, call 1-888-830-1326 for replacements. x5 A *B *C 3/8" Cable Connector x2 D Extra Screws * NOTE: Strain relief cable connector must be installed. Not Included. Before Installation 1 Tools Needed. (Not supplied.) Estimated assembly time: ...

Owner's Manual - Page 6

Make sure all wiring connections are inside the box or under the wiring cover plate. Tape joints. A14 Fan Motor Night Light Light Black 2 Pin White White Red Night Light 3 Pin Black Light *Option *Option Fan & Main Light Together Ground Green A Bare Copper Black Main Switch 1 (AC In) White Red Switch 1 (AC In) Black Switch 2 (AC In) Connect wires...

Owner's Manual - Page 9

... 2 Pin White White Red Night Light 3 Pin Black Light *Option *Option Fan & Main Light Together Ground Green A Bare Copper Black Main Switch 1 (AC In) White Red Switch 1 (AC In) Black Switch 2 (AC In) Connect wires as shown. B20 B21 G H Install the wiring cover plate. Make sure all wiring connections are inside the box or under...

Owner's Manual - Page 11

... 09/09/2011 Mark position of your sheetrock. C13 Slide the mounting rails into brackets. Existing Construction - accessible from above C11 EXISTING FAN NO EXISTING FAN OR Remove an existing fan and check to mark position. C14 5/8 1/2 5/8 1/2 Position the correct depth mark at the bottom edge of the joist based on the thickness...

Owner's Manual - Page 13

... the strain relief screws. Make sure all wiring connections are inside the box or under the wiring cover plate. C22 Fan Motor Night Light Light Black 2 Pin White 3 Pin White Red Night Light Black Light *Option *Option Fan & Main Light Together Ground Green A Bare Copper Black Main Switch 1 (AC In) White Red Switch 1 (AC In) Black Switch 2 (AC...

Owner's Manual - Page 15

...-01 09/09/2011 Existing Construction - For supply connection, use wires suitable for at least 90º C (194º F). accessible only from below D11 EXISTING FAN D12 F Remove an existing fan and check to make sure the opening is large enough to be purchased. D15 Attach existing ducting to duct connector.

Owner's Manual - Page 16

... HANG FROM THE WIRING HARNESS. Make sure the wires are inside the box or under the wiring cover plate. D16 Fan Motor Night Light Light 2 Pin Black White White Red Night Light 3 Pin Black Light *Option *Option Fan & Main Light Together Ground Green A Bare Copper Black Main Switch 1 (AC In) White Red Switch 1 (AC In) Black Switch 2 (AC...

Owner's Manual - Page 18

... K M Position the strain relief bracket between the plugs as shown until it locks into slots. E7 Install 2 Max 60 watt A-15 bulbs (Not Included). Slide light fixture over posts. E5 Align posts A, B, C and D (stamped into motor housing) with slots on glass dome assembly with posts A, B, C and D (stamped into place.

Owner's Manual - Page 19

...power on, replace fuse, or reset breaker. • Check all plug connections to be sure they are extremely quiet. Trouble Shooting Problem: Fan does not come on. Solution: • Hunter Fan Bath Ventilators are secure....09/2011 Problem: Light does not come on , replace fuse, or reset breaker. • C heck all fasteners. • Check the glass to make sure it moves freely.

Owner's Manual - Page 20

... consumer purchaser of this Hunter bath exhaust fan: If any part of your Hunter bath exhaust fan (except for glass fixtures and light bulbs) fails at any time within five years after the date of sale to you due to a defect in material or workmanship, we will repair or, at our option, replace the defective part free...