Hunter 23566 Support Question
Hunter 23566 Support Question
Find answers below for this question about Hunter 23566.Need a Hunter 23566 manual? We have 4 online manuals for this item!
Question posted by bobwinton on March 7th, 2014
The Rubber Grommets Are Installed In The Holes In The Fan That Are Then Secured
to the fan blade arm with screws that go thru the grommet.
Current Answers
Related Hunter 23566 Manual Pages
Installation Guide - Page 1
...box is secured to recess the bottom of the outlet box a minimum of the fan and ...Installing the Ceiling Plate.
Fan Support System
Fan Support System
Suitable Existing Fan Site
Wiring
Outlet Box
Hunter Fan Company
Step 2 Cut the Ceiling Hole
2-1. For instructions to install your fan manual and begin with the rotating fan blades during normal operation.
• e fan blades...
Owner's Manual - Page 2
... bend the blade attachment system when installing, balancing, or cleaning the fan. We appreciate the opportunity to supply you complete instructions for installing and operating your fan. Save these...before installing your fan, disconnect the power by turning off position, securely fasten a prominent warning device, such as a tag, to the service panel. • is fan is installation and...
Owner's Manual - Page 3
... performance of three ways, depending on ceiling height and your Hunter fan, use the accessories, follow the instructions included with each product. Installer's Choice and Optional Accessories
Understanding Mounting and Installer's Choice®
Hunter's patented 3-position mounting system provides you can install your Hunter fan in one of your preference: Low Profile, Standard, or Angle...
Owner's Manual - Page 4
... the following tools for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. Proper ceiling fan location and attachment to the motor or fan blades.
If any shipping damage to the building structure are essential for any parts are installing more than
one fan, keep the fan blades and
blade irons (if applicable) in the...
Owner's Manual - Page 5
... wood screws and pass the screws through the hole in the middle of the threaded screw holes in the ceiling plate with the slots and holes on...Fan Company Note: e ceiling gasket should be flush against the ceiling.
2-6. 2 • Installing the Ceiling Plate
CAUTION: To avoid possible electrical shock, before installing your fan, disconnect the power by turning off position, securely...
Owner's Manual - Page 6
.... 3 • Assembling and Hanging the Fan
Steps 3-1 - 3-2
Adapter Steps 3-7 - 3-8 Low Profile Screw Motor Housing
6
Alignment Hole
Step 3-9
WARNING: Fan may fall if not assembled as directed in the housing. 3-7. To assemble fan to install the pipe and ball assembly. Hunter Fan Company
42701-01 • 01/25/06 Securely retighten the set screw on the pipe will still be...
Owner's Manual - Page 7
... or wire strands are not included. Push all wires and wire nuts into the outlet box.
4 • Wiring the Fan
Wire Nut Single Switch Wiring
7
42701-01 • 01/25/06
Hunter Fan Company
Select an acceptable general-use a qualified electrician. Wall switches are visible after making connections. All wiring must be...
Owner's Manual - Page 8
.... 5-2. Insert and tighten the mounting screws securely.
Note: If necessary, lift the side of the gasket to insert the screws into the mounting holes on the
ceiling plate. 5-3. Align the holes in the canopy with the mounting holes on the ceiling plate. Mounting Screw
8
Hunter Fan Company
42701-01 • 01/25/06 5 • Installing the Canopy
Steps 5-1- 5-3
Canopy...
Owner's Manual - Page 9
...Hunter Fan Company Your fan may appear slightly loose after screws are installed in the motor to a blade iron using three blade assembly screws. Attach each blade, insert one blade mounting screw through the blade iron, and attach lightly to the fan).
6-1. If you used grommets, the blades may include blade grommets.
If your fan has grommets, insert them by hand into the holes...
Owner's Manual - Page 10
... using a mild detergent and a slightly dampened cloth. Slide the reversing switch on electrical power to prevent scratching. Restart fan. Turn on the fan to a complete stop. Ceiling fans work best by blowing air downward (counterclockwise blade rotation) in
10
the same manner as they will distribute the warmer air trapped at the ceiling around...
Owner's Manual - Page 11
... switch is properly seated. Loosen canopy, check all the blades. Tighten the blade bracket screws until snug. 2. If so, replace all connections according to the "Wiring the Fan" section. 3. If your fan wobbles when operating, use the enclosed balancing kit and instructions to see if the blade is on , replace fuse, or reset breaker. 2. Turn power...
Parts Guide - Page 1
... Chain
76 Pull Chain Pendant
28 Switch Housing
29 Switch Housing Cover
Hardware (Drawn to Scale)
75 Balancing Kit 44 Blade Iron Set
Wood Screw Wood Screw
8 Set Screw
100 Locking Screw
40 Housing Cover Screw
Wire Nut
Flat Washer
Blade Iron Armature Screw
67 Blade Assembly Screw
62 Canopy Screw
71 Isolator
R If parts are included in
your Instruction Manual. 2.
Parts Guide - Page 2
...Kit Assembly (Not Shown)
74
Light Kit Adapter
76
Pull Chain Pendant
78
Pull Chain
150
Globe / Shade (Not Shown)
* Hardware Kit
47
Screw, Blade Iron Armature
67
Blade Assembly Screw
70
Wire Nut
75
Balancing Kit
Model # Asm. Dwg. #
Finish Qnty
1 1 1 1 1 1 3 2 2 4 4 3 ... 63755-03-247 03482-05-247 05172-01-000 07570-01-000
23566 92535-02
White Part #
83525-01-000 83521-01-132 74254-01...
Similar Questions
I Need Rubber Grommets For A Model 28681 To Secure Blades.
I had to search for a white grommet and hope that they were the right part for the ... for a Hunter ...
I had to search for a white grommet and hope that they were the right part for the ... for a Hunter ...
(Posted by Omprakash1 3 years ago)
I Need Rubber Grommets For A Model 28681 To Secure Blades.
I need the rubber grommets for model 28681 to secure the blades.
I need the rubber grommets for model 28681 to secure the blades.
(Posted by mgregan05 3 years ago)
How Do I Install My Fan Without The Light Kit?
how do I install my fan without the light kit
how do I install my fan without the light kit
(Posted by Mgdel634 7 years ago)
Where Can I Purchase Rubber Grommets For My Hunter Fan?
(Posted by bobwinton 10 years ago)
Can I Install This Fan Without The Light Kit?
Can I purchase a cap to cover the light kit mount so this fan can be installed without the light kit...
Can I purchase a cap to cover the light kit mount so this fan can be installed without the light kit...
(Posted by evadwest 10 years ago)