Humax IR-ACE Support Question
Humax IR-ACE Support Question
Find answers below for this question about Humax IR-ACE.Need a Humax IR-ACE manual? We have 1 online manual for this item!
Question posted by jeff07 on June 12th, 2012
Humax Ir-ace Ii Dvb Mpeg2 Digital Wont Acquire Galaxy 17 @ 91w With 71% Signal?
The person who posted this question about this Humax product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Humax IR-ACE Manual Pages
User Manual - Page 3
.... Do not stand the STB on top of the STB must comply with SABS 061. CONNECTION TO THE SATELLITE DISH LNB : Disconnect the STB from the satellite dish.
EARTHING
: The LNB cable MUST BE EARTHED.
GB2 Please read the following safety precautions carefully. MAINS SUPPLY : 90 - 250 V AC 50/60 Hz
OVERLOADING...
User Manual - Page 4
...held responsible for any problems caused by the orientation of software versions other than HUMAX official software will void the manufacturer's warranty.
It is tuned. • Transponder An automatic device that receives, amplifies and retransmits a signal on a different frequency. This includes a satellite dish and a broadband antenna. • Forward Error Correction (FEC) An error control...
User Manual - Page 5
...
connector. 2. GB4 Do the same for example analogue) to the digital receiver or several antennae via . Loop Via If you have two or more fixed antennae or LNBs, you can connect either a single satellite antenna directly to the common antenna equipment receiver that has satellite signals.
4. Connect one end of a Coaxial cable to the LNB OUT...
User Manual - Page 6
GB5 Over The Air (OTA) is found at the HUMAX website - The latest news and releases on software versions may be received). 5. Software Upgradeing The HUMAX digital set-top box is a highly sophisticated product-incorporating one used by "beaming" the latest software versions over the air via satellite systems. Note that OTA is recommended that users...
User Manual - Page 8
... LED light goes on when in TV mode. PUse to volume up .
RADIO LED (YELLOW) The LED light goes on when in RADIO mode. V+ (Model IR-ACE M only) Use to change services up .
(STANDBY) Press to volume down . V - (Model IR-ACE M only) Use to switch between TV and Radio modes.
User Manual - Page 9
STB Connections
Rear Panel
IR-ACE IR-ACE M
GB8
User Manual - Page 10
AUDIO OUTPUT Audio signal from your TV doesn't have a RCA/Cinch Jack, use to VCR or TV. GB9 RF OUT If your STB to connect an antenna. RS-232C Use when connecting to connect a terrestrial antenna. RF IN Use to your TV.
LNB IN Use to VCR or TV. VIDEO OUTPUT Video signal from your STB to connect your PC.
User Manual - Page 11
.../TV system. With a Hi-fi System 1. If your TV doesn't have a RCA/Cinch socket, connect one end of the following set-ups:
Note: STB model IR-ACE shown; Connect one end of the STB to the LINE, AUX, SPARE OR EXTRA input sockets on your TV. STB Connections
There are the same...
User Manual - Page 12
... cable from the LNB of your motorised system(DiSEqC 1.2 Motor)
to the LNB IN socket on your VCR. 3. Note: STB model IR-ACE shown; connections are the same for model IR-ACE.
GB11 Connect one end of a RCA/Cinch cable to the RCA/Cinch connector on the STB
and the other end to a RCA...
User Manual - Page 14
... note : The design of the Remote Control Unit may be used to change services (up/down) and increase or decrease the audio volume (left/right).
17 EXIT
Press to return to select a Service Alphabet in the Service List. GB13 This button functions in the same way as the BLUE button icon...
User Manual - Page 15
... press thei ( ) button. Press the button to return to the
service attributes. • Progressive Signal Quality bar. Service Part
The service information is situated on the left side of the I-Plate and ...not displayed and cannot return to from the following items:
• Current Time, Dolby Digital Symbol if there is an available Dolby service.
• Service name, Service Number, icon...
User Manual - Page 17
...the current service, proceed as follows: 1.
Subtitle If there is encoded by Dolby Digital, the Dolby Digital Symbol will appear in the list of supported subtitle
languages. 3. Function Guide
Soundtrack ... is preserved regardless of the change ,
or the EXIT ( ) button to decode the Dolby Digital audio. Press the OK ( ) button to confirm the change of supported audio
languages. 3. Press...
User Manual - Page 25
... Parental Guidance Rating is possible to verify it is given as follows: 1. Main Menu Guide
2. Parental Control In the Parental Control menu, it .
When four digits
have been entered, the cursor will automatically be moved to the New PIN code menu. 4. Select the Censorship classification item using the
button. 4. When four...
User Manual - Page 41
... all services belonging to the transponder list column using the button. 4. Press the RED button to mark the transponder name. 5. Move the cursor to the satellite and the transponder. GB40 It will also delete all services belonging to
the transponder. • Sort the services according to the...
User Manual - Page 42
... can be supported, one of LNB in the signal line. It can also be set on "High". It can assign up to each antenna.
The LNB voltage may drop too low to supply power to the LNB due to each antenna.
The available satellite names supplied by the user with the "User...
User Manual - Page 45
...as parameters. To obtain the updated information, please consult the HUMAX web site. Antenna Alternative Specifies the satellite in which the automatic search will be performed.
If this ... Automatic Search may take a long time to search all the parameters according to the satellite information. 3. Activate the Automatic Search menu. 2. Set all the services, depending on...
User Manual - Page 46
...via the Main menu. 2.
GB45 To receive the information, proceed as follows: 1.
Signal Detection The Signal Detection menu supplies information on OTA availability....satellite as : • Information on the Software version, • Information on the Hardware version, • Information on the signal level of the current locked TP, • Information on signal level and signal...
User Manual - Page 51
... the
buttons to find .
When you exit the menu.
14. You should register a signal once. During the move your East Limit. This is the satellite's position. If there two or more different positions register a
signal, then you must access the Satellite Settings menu. Use the
buttons to display the
Service Searching menu.
2. If you...
User Manual - Page 57
...Irdeto Embedded
1 Slot Smart card
Tuner & Channel
Input Connector Frequency Range Input Impedance Signal Level IF IF Band width LNB Power & Polarisation
22 KHz Tone DiSEqC Control ... stream specification MPEG-2 MP@ML 15 Mbit/s Max 4:3, 16:9 720 x 576 MPEG/MusiCam Layer I & II Single channel/Dual channel/Joint stereo/Stereo 32, 44,1 and 48 KHz
Memory
Main Processor Flash Memory Graphic(MPEG...
User Manual - Page 58
...D)
Weight (Net) Operating Temp Storage Temp Storage Humidity
260 x 50 x 182 mm (IR-ACE) 310 x 60 x 225 mm (IR-ACE M) Around 3.0 kg 0°C to + 45°C -10°C to EUTELSAT. The...(Non-Condensing)
• You can use a special antenna switch with the picture quality of digital TV programmes.
When changing ASTRA1 to EUTELSAT, for example, a DiSEqC command is a protective ...
Similar Questions
Sw Update For Satellite Receiver Humax Ir Ace Ii
Looking for the assistance how to do manually the soft ware update for my receiver HUMAX IR-ACE II.W...
Looking for the assistance how to do manually the soft ware update for my receiver HUMAX IR-ACE II.W...
(Posted by rlotfi 9 years ago)
Humax Dvb Ir Ace Ii
how can i restore channels on my humax dvb ir ace II
how can i restore channels on my humax dvb ir ace II
(Posted by fati143 10 years ago)
How Can I Update The Softwae Of Humax Ir-ace Ii (silver) To The Latest Versions
(Posted by aboamjad 11 years ago)
How Can I Watch Sabc Tv On Humax Ir-ace Ii
what is the code to watch SABC TV of South Africa which is on free to air
what is the code to watch SABC TV of South Africa which is on free to air
(Posted by rpmharawa 12 years ago)