Hoover U5753 Support Question
Hoover U5753 Support Question
Find answers below for this question about Hoover U5753.Need a Hoover U5753 manual? We have 1 online manual for this item!
Question posted by djweeks on July 4th, 2013
Power Switch
How do you replace the power switch. The new switch we received for this model has two black wires and the original plugs in.
Current Answers
Related Hoover U5753 Manual Pages
Manual - Page 2
...To unplug, grasp the plug, not the cord. Your cleaner is model and has serial number...Replacing Agitator Brush Roll ......11 Replacing Power Hand Tool
Agitator Brush Roll 12 Replacing Belt 10-11 Replacing Power Hand Tool Belt ..12 Replacing Edge Groomers 11 Replacing...Authorized Hoover Warranty Service Dealer (Depot).
• Use vacuum cleaner only for warranty service of your HOOVER product....
Manual - Page 3
... missing.
Continued § 3 If you should happen to need assistance during assembly or operation, call:
Visit us on cleaner) D. Powered hand tool (some models)
Note: The white switch lock above the ON/OFF switch aids in our Consumer Response Center.
Assembling cleaner
This cleaner was inspected and packaged carefully before disposing of service outlet...
Manual - Page 4
... storage area. Remove powered hand tool (some models). Open tool cover on back of handle.
Dispose of handle.
Make sure that the switch is in the OFF position.
1-5
1-6
C D
Slide handle section onto back of switch lock. If switch lock has come off during assembly, make sure switch is in OFF position (down) before plugging into holes on...
Manual - Page 5
... reduce the risk of your cleaner from room to
*Some models only
operating or low positions.
15. If the plug does not fit fully in rear wand.
25 14. ON-OFF switch
Plug cord into electrical outlet. To turn cleaner OFF, push switch down.
2-2
2-3
2-4
Transporting cleaner
To move your cleaner has three positions; Hose
22...
Manual - Page 6
... Bare Floor
D
C
Carpet height adjustment
The cleaning of carpet and rugs takes place at the nozzle (C). To decrease the feature's sensitivity to dirt, set the switch (B) to the "HI" position.
• At other end or edge.
Move cleaner back to start again, lower nozzle, and use only forward strokes.
6
this means...
Manual - Page 7
...2-15
O
P
Extra reach hose*
Push ON/OFF switch to OFF position. Twist wand or tool slightly to tighten or loosen the connection. Do not submerge powered hand tool in place.
2-14
I
J
K
L
...will continue to rotate. To reattach, align hinges of stairs. *some models
Stair cleaning
Use the hose and powered hand tool* or furniture nozzle for upholstered furniture, draperies, mattresses, clothing,...
Manual - Page 8
... the left to empty
It is in place. Tap side of the dirt cup as described in "How to remove from the HEPA cartridge filter.
3-4 F
G
Replace dirt cup lid.
CAUTION: Very fine materials, such as proper use if preferred. Push latch (F) to empty
Disconnect cleaner from entering the HEPA cartridge filter...
Manual - Page 9
... outlet. The pre-filter (C) can be cleaned by tapping either of dirt cup. Allow pre-filter to replace this filter, ask for HOOVER part No. 38762008.
3-13
L
Cleaning final filter
The final filter assists.... DO NOT rinse HEPA cartridge filter with a "breakaway" feature which allows it is felt.
Replace lid and return cup to snap free if it to cleaner (Fig. 3-4). Make sure the white...
Manual - Page 10
.... 3-17), removing agitator (Fig. 3-18), and lifting agitator shield (Fig. 3-20).
3.
What to replace
Disconnect cleaner from electrical outlet.
2. When purchasing a new belt, ask for the effective operation of socket. Replacing lens
Reposition lens and secure with your cleaner.
Replace belt if it is important for HOOVER part No. 38528033.
3-17
A
How to buy...
Manual - Page 11
... and 4 Phillips head screws. Continue following directions in "The belt" section beginning with 4 Phillips head screws.
11
3-19 B
3-20
3-21 F
C
D
Installing new belt With lettering on outside of the nozzle, should be replaced when they appear worn. E
D
Replacing agitator brush roll
Insert agitator through belt and place belt in "The belt" section to...
Manual - Page 12
... bottom plate (A).
3-28
3-29
B
3-27
D
C
3. Replace with new belt. Unscrew the two Phillips screws and remove belt guard (B). ...replace 1.
Remove tool from turbine pulley (F). Powered hand tool
Belt replacement Inspecting the belt
The powered hand tool belt is designed to ensure that it is not normally replaced. Powered hand tool
(some models only)
Agitator brush roll replacement...
Manual - Page 13
... cause Possible solution
• Not firmly plugged in • Plug unit in firmly
• No voltage ...Powered hand tool (some models) brush roll won 't pick up
Possible cause Possible solution
• Broken or worn belt • Replace belt
• Agitator brush roll worn • Replace...under "Vacuum Cleaners - Refer to motor bearings.
Other performance factors include Hose Power (ASTM...
Manual - Page 14
...Fig. 3-20) and remove any blockage. 2. C. Disconnect powered hand tool from turbine channel (D). Warranty service can only ... • Belt broken or stretched • Replace agitator brush roll belt as described in a ...blockages continuing with the Owner's Manual against original defects in the U.S.A., phone 1-800-... occurs during tool use (some models only):
4-3 D
1. Remove bottom plate,...
Manual - Page 36
HOOVER y
®son marcas registradas
HOOVER et
®sont des marques déposées
HOOVER and
® are registered trademarks
3-04 U5753-/65-/67-/69-900
Printed in Mexico
56511-C19
Similar Questions
I Need A Replacement Front Wheel For My Hoover Model # Uh71214
(Posted by mangle1255 8 months ago)
How To Disassemble To Replace Power Switch On Hoover Elite Rewind Uh 71003
(Posted by Anneormsby125 4 years ago)
Replacement Dirt Cup Canister For Hoover Model Bh53110
where can I buy a new dirt cup canister for my Hoover cordless stck vac?
where can I buy a new dirt cup canister for my Hoover cordless stck vac?
(Posted by elizabethacquisto 5 years ago)
Replace Power Switch On Hoover Floormate Fh40030?
My Hoover Floormate FH40030 won't turn on. It worked perfectly 2 days ago. It turned off normally. N...
My Hoover Floormate FH40030 won't turn on. It worked perfectly 2 days ago. It turned off normally. N...
(Posted by local210 10 years ago)
No Suction In Power Head
hoover 5753-955 Wind Tunnel. no suction in our power head. The hand nozzle has good suction. Belt i...
hoover 5753-955 Wind Tunnel. no suction in our power head. The hand nozzle has good suction. Belt i...
(Posted by taschajasper 12 years ago)