Hoover FH40010B Support Question
Hoover FH40010B Support Question
Find answers below for this question about Hoover FH40010B.Need a Hoover FH40010B manual? We have 1 online manual for this item!
Question posted by lizzysdad on November 27th, 2013
How To Replace The Suction Motor Without Ending Up Tearing It All Apart
Looking for procedural steps for tear down and replacement of suction motor
Current Answers
Related Hoover FH40010B Manual Pages
Manual - Page 4
... cord or plug.
Whenever the adapter is for machine applica- NOTE: In Canada, the use on a nominal 120-volt circuit and has a grounding plug that looks like (F) extending from the adapter must be inserted into an appropriate outlet (B) that is not working as it should malfunction or breakdown, grounding provides a path...
Manual - Page 6
... at voltage specified on data plate on pedal (A) to lower handle to turn cleaner OFF.
2.2
A
Handle release pedal
2.3 Step on bottom of
15. Upper Handle Release Button
This cleaner is intended for
drying and vacuuming
5. Handle Release Pedal
ON/OFF switch
2.2 Push switch (A) once to operating position. ON/OFF Switch 3. Solution Trigger...
Manual - Page 7
... dial (A) turns the brushes on and off the floor surface.
Refer to "How to the DRY position.
To move your cleaner from room to the VACUUM position. For wet pickup, turn the dial to Clean" section for complete cleaning instructions.
2.6
2.7
A
VACUWUAMSDHRY
7 Transporting
2.4.
Manual - Page 8
... disconnect from electrical outlet. For hard surface floors such as these conditions could lead to damaged flooring when using water to serve as shown.
2.13 Replace cap.
The Clean Water Solution Tank holds detergent and water that can normally be cleaned using , as vinyl, linoleum, marble, laminate wood, polyurethane sealed wood...
Manual - Page 9
... be emptied after dry vacuuming and before wet operation. Replace lid onto Dirty Water Tank...suction shut-off is built into cleaner body until snapped in lid.
Empty tank.
2.15
G
filters
The tank lid contains a washable, reusable filter. Clean this time.
2.15 To remove tank, press down firmly until snapped in place.
2.20 To replace Dirty Water Tank, place bottom of the motor...
Manual - Page 10
... to: • VACUUM: Vacuum to VACUUM position and vacuum floor. The brushes...trigger to WASH position.
To greatly enhance drying of suction (see "Automatic shut-off" section).
3.2
A... Dirty Water Tank or clean the filter when the motor sound becomes higher in your cleaner. 3. To wet...Mode selector dial to release solution as needed.
Step on sealed wood floors, inspect floor surface for...
Manual - Page 11
... use the cleaner to pick up flammable or combustible liquids or chemicals. nozzle: How to Clean
Your carpet cleaner is equipped with a damp cloth.
4.4 To replace nozzle, make sure latches (D) are out.
Do not use and care of nozzle with these home maintenance tasks as proper use the cleaner to pick...
Manual - Page 12
... a wood surface unless cleaner is equipped with bearings which contain sufficient lubrication for the life of the motor.
Do not add lubricant to prevent leaking. To reduce the risk of lubricant could cause damage. Replace tanks.
4.8 D
C
4.10
4.7 B
A
4.9
FG E
E
StorAGE
Before storing cleaner:
Turn cleaner OFF and disconnect from moving parts,
unplug cleaner...
Manual - Page 13
...Tank.
4. Cleaner solution won't dispense
Brushes won 't run
1. Clean Water Solution Tank is replaced properly and locked. Check fuse or breaker in place. 4. WARNING ! Power cord not firmly... is
in place.
4. Tanks not in place.
5. Refill Clean Water Solution Tank.
1.
Low suction
1.Washable Filter is found by an authorized service representative.
! Dirty water tank full.
3. Make ...
Manual - Page 14
...representative call1-800-263-6376; Mon-Fri 8am-7pm EST. Do not send your vacuum by :
• Checking the Yellow Pages under "Vacuum Cleaners" or "Household". • Visit our website at hoover.com (U.S. In ...Phone: 1-800-263-6376, Mon-Fri 8am-7pm EST. Always identify your vacuum to the store.
14 This will only result in Glenwillow for service. If you . • ...
Manual - Page 16
... state to you specific rights; Military Exchange and outside the country in a commercial operation (such as warranted, take or send the product to correct any replacement or repair performed under the laws of the state of consequential damages, so the above exclusion may not apply to state.
16 This warranty gives...
Similar Questions
Hoover Floor Mate 40010 Replacement Of Satin Silver Hose
All done but the big piece on the bottom won't fit back in in order to start the floormate
All done but the big piece on the bottom won't fit back in in order to start the floormate
(Posted by Cleany77 9 years ago)
Hoover Fh40010b Floormate Spinscrub Wet/dry Vacuum Won't Stay On.
Floormate keeps shutting off. I checked all the seals and cleaned everything, but it still shuts off...
Floormate keeps shutting off. I checked all the seals and cleaned everything, but it still shuts off...
(Posted by 0rosie 10 years ago)
Hoover Motor Assembly Part 440001582
Instructions on how to replace the motor assembly on model sh40060?
Instructions on how to replace the motor assembly on model sh40060?
(Posted by earlchambers 11 years ago)
Stopped Suction
Bought only four months ago and it stopped sucking up the solution. What happened?
Bought only four months ago and it stopped sucking up the solution. What happened?
(Posted by joycepking 12 years ago)
How Do I Make It Suck Again?
my vacuum is a year old and now it wont suck 90% of things and smells funny. it sounds normal though...
my vacuum is a year old and now it wont suck 90% of things and smells funny. it sounds normal though...
(Posted by Anonymous-34486 12 years ago)