Honeywell RTH2310B Support Question
Honeywell RTH2310B Support Question
Find answers below for this question about Honeywell RTH2310B.Need a Honeywell RTH2310B manual? We have 1 online manual for this item!
Question posted by Dezzjul on March 8th, 2014
Honeywell Thermostat Indoor Temp Does Not Match Set Temp
The person who posted this question about this Honeywell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Honeywell RTH2310B Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-04
Owner's Manual - Page 2
... wires. 4) Mount the new wallplate. 5) Connect the wires. 6) If the wire labels don't match. 7) Specify the furnace type. 8) Install the batteries. 9) Install the thermostat. 10) Set the system.
Do you need assistance? Quick Installation Guide
Installation is Easy
Your new thermostat has been designed for fast and easy installation. We are here to help.
Owner's Manual - Page 3
... the following systems:
• Gas, oil or electric furnace • Central air conditioner • a hot water system with heat pumps or multi-stage systems.
2
This thermostat is not compatible with or without pump • a millivolt system • a central heating and cooling system
If you are not sure of your system type...
Owner's Manual - Page 4
... power off at the heating/cooling system.
2) Remove old thermostat, but leave wallplate with wires attached. Do not remove wallplate yet. Contact your old thermostat in the trash if it contains mercury in a sealed tube. MERCURY NOTICE: Do not put your local waste management authority for instructions regarding recycling and ...
Owner's Manual - Page 5
... the bare metal end of these wires with electrical tape, so it cannot touch and short other wires. RTH2310 Programmable Thermostat
3 Identify Wires
3.
Wrap the wires around a pencil to identify wires. Do not use non-connected wires.
Do ...wires are attached to a terminal marked C or C1, they will not be connected to your new thermostat. If any wires are not attached to your old...
Owner's Manual - Page 6
Quick Installation Guide
4 Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes). Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5 Insert plastic anchors.
Owner's Manual - Page 7
... if you have both R and Rc wires.
1) Match each labeled wire with the terminal having the same letter.
2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws.
3) Push any terminal on the thermostat, see next page.
6 If a wire does not match any excess wire back into the wall opening...
Owner's Manual - Page 8
If wires are connected to both Rh and Rc terminals, remove jumper (see diagram below. Do not use C, X or B. Quick Installation Guide
6 Connect Wires (less common wiring)
If a labeled wire does not match any terminal designation, see previous page).
7 Wrap bare end of wire with electrical tape.
Owner's Manual - Page 9
J2 jumper
HG Leave the jumper in this position if you have an electric furnace.
8
HE Place the jumper to the G terminal. RTH2310 Programmable Thermostat
7 Specify Furnace Type
6.
Set the Jumper J2, on the back of the thermostat, if you have connected a wire to this factory-set position if you have a gas or oil furnace.
Owner's Manual - Page 10
...;C).
9 Observe the
polarity. 3) Reinstall the battery cover. It is normal that the displayed temperature be higher than the ambient temperature if you are installed, the thermostat performs a series of tests for approximately 5 seconds. Quick Installation Guide
8 Install Batteries
7.
1) Pull out the battery cover. 2) Install the batteries as shown...
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
9 Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 12
...system switch to the next function, briefly press both and buttons simultaneously.
3) To change the setting, press the or button. Quick Installation Guide
10 System Setup
9.
1) Press both and ...12 min (alternate setting for 3 seconds to enter or exit the setup menu.
2) To advance to switch between the two parameters.
4 For optimal heating control, use the setting that matches your system as ...
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-04
Similar Questions
Indoor Temp And Setting Don't Match
I installed the round CT87K yesterday. I have an oil boiler with hot water baseboard heat. I got the...
I installed the round CT87K yesterday. I have an oil boiler with hot water baseboard heat. I got the...
(Posted by kcneill8 3 years ago)
How To Hold Temp Thermostat Rth2310b Manual
(Posted by demdigio 9 years ago)
How To Replace The Battery In A Honeywell Thermostat Rth2310b
(Posted by acedc 9 years ago)
Video Of How To Set A Honeywell Thermostat Rth2310b
(Posted by karaSnie 10 years ago)
