Honeywell RTH2310 Support Question
Honeywell RTH2310 Support Question
Find answers below for this question about Honeywell RTH2310.Need a Honeywell RTH2310 manual? We have 1 online manual for this item!
Question posted by buddy2004 on August 29th, 2012
How To Change A Battery In A 7 Day Programable Thermostat
The person who posted this question about this Honeywell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Honeywell RTH2310 Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-02
Owner's Manual - Page 2
... in the following pages.
Identify your system type. Remove your old thermostat. Identify the wires. Mount the new wallplate. Connect the... Install the batteries. Install the thermostat. Set the system.
Do you need assistance? Quick Installation Guide
Installation is Easy
Your new thermostat has been designed for ...
Owner's Manual - Page 3
RTH2310 Programmable Thermostat
Identify System Type
1. This thermostat is compatible with the following systems:
• Gas, oil or electric furnace • Central air conditioner • a hot water system with heat pumps or multi-stage systems.
2 This thermostat is not compatible with or without pump • a millivolt system • a central heating and cooling system
...
Owner's Manual - Page 4
... waste management authority for instructions regarding recycling and proper disposal.
3 Contact your old thermostat in the trash if it contains mercury in a sealed tube. Quick Installation Guide
Remove Old Thermostat
2.
1) Turn power off at the heating/cooling system.
2) Remove old thermostat, but leave wallplate with wires attached. Do not remove wallplate yet.
Owner's Manual - Page 5
... electrical tape, so it cannot touch and short other wires. Do not use non-connected wires. If any wires are not attached to your new thermostat. Disconnect wires and remove the old wallplate only after all wires are attached to a terminal marked C or C1, they will not be connected to your...
Owner's Manual - Page 6
Quick Installation Guide
Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes). Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5 Insert plastic anchors.
Owner's Manual - Page 7
If a wire does not match any excess wire back into the wall opening. Labels don't match? RTH2310 Programmable Thermostat
Connect Wires (typical wiring) 5.
Remove jumper if you have both R and Rc wires.
1) Match each labeled wire with the terminal having the same letter.
2) ...
Owner's Manual - Page 9
HE Place the jumper to this factory-set position if you have an electric furnace.
8 RTH2310 Programmable Thermostat
Specify Furnace Type
6. Set the Jumper J2, on the back of the thermostat, if you have a gas or oil furnace.
J2 jumper
HG Leave the jumper in this position if you have connected a wire to the G terminal.
Owner's Manual - Page 10
.... You will display the ambient temperature once it is normal that the displayed temperature be higher than the ambient temperature if you are installed, the thermostat performs a series of tests for approximately 5 seconds. Quick Installation Guide
Install Batteries
7.
1) Pull out the battery cover. 2) Install the batteries as shown. Observe the
polarity. 3) Reinstall the...
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 12
... min (alternate setting for 3 seconds to enter or exit the setup menu.
2) To advance to the next function, briefly press both and buttons simultaneously.
3) To change the setting, press the or button. DISPLAY
DESCRIPTION
OPTIONS 1
Temperature display
°C or °F
Time display
12 h or 24 h
Early Start 2
On or Off
Heating...
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-02
Similar Questions
How To Change Batteries On A Honeywell Thermostat Rth110b
(Posted by pjSnicke 10 years ago)
Nearly Blank Screen
My Honeywell screen is fading, we've changed batteries still nearly blank screen, think the model is...
My Honeywell screen is fading, we've changed batteries still nearly blank screen, think the model is...
(Posted by Karenanderson1234 10 years ago)
How To Change Battery In The T8775c Thermostat?
(Posted by sherriblixt 12 years ago)
I Changed My Batteries With Fresh New Ones. Now My Backlit Display Is Not Visibl
Is there a reset button?
Is there a reset button?
(Posted by cdavies 12 years ago)