Home » Honeywell » Thermostats » Honeywell CT3200

Honeywell CT3200 Support Question

Find answers below for this question about Honeywell CT3200.
Need a Honeywell CT3200 manual? We have 1 online manual for this item!

Honeywell Overview Questions Manuals Reviews Videos Research

Question posted by nvazSOMET on July 25th, 2014

Installed New Honeywell Thermostat Now Furnace Will Not Come On Unless You Run

the hot water

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Honeywell CT3200 Manual Pages

Owner's Manual - Page 1

... savings with your home, keeping you have any questions about using this thermostat, visit our home expert Web site at www.honeywell.com/yourhome or call Honeywell Customer Relations at 1-800-468-1502. If you comfortable while saving energy. MagicStat® CT3200 Programmable Thermostat Installation and Programming Instructions Weekday/Weekend (5-day/2-day) Programmable Heat and/or...

Owner's Manual - Page 2

... include warm air furnaces and hot water. Steam A steam boiler with more than one stage. Multistage Conventional A heating or cooling system with radiator heat. model Yes No CT1950 for instructions regarding recycling and the proper disposal of thermostat is not compatible with CT3200? Heating/Cooling System Conventional Single stage systems that the CT3200 is the right...

Owner's Manual - Page 3

Prepare for installation a. Carefully unpack your heating and cooling systems are working properly. Make sure that your new thermostat. Honeywell recommends Energizer® • Wire cutter/stripper or sharp knife batteries. • Level • Screwdriver • Electrical tape • Hand or power drill with either ...

Owner's Manual - Page 4

... wrap the wires around a pencil to the heating/cooling system, either at the furnace or at the fuse/circuit breaker panel. Remove the old thermostat Fig. 2 Fig. 3 M20140 Fig. 4 M19086 WIRES THROUGH WALL OPENING 4 INSTALLATION M20133 a. d. If the wiring meets any of the following conditions, see the wiring cross reference table on the...

Owner's Manual - Page 5

...and tighten the mounting screws. Check your progress The mounting plate is now mounted on the wall. Step 3. Install the mounting plate Fig. 5 M20139 Fig. 6 M20129 Fig. 7 a. c. b. d. Remove the mounting plate and...none of the mounting plate's screw holes. Separate the mounting plate from the thermostat using a coin, as shown in drywall, gently tap the anchors that were provided into ...

Owner's Manual - Page 6

... HOT WATER A-OUT B-IN F BOILER 1 TURN ELECTRIC A-IN B-OUT E FURNACE 1 TURN W Y G R Rc FUEL SWITCH M20145 IMPORTANT: Setting your thermostat correctly for your heating system uses: F-gas or oil, or E-electricity. Note: These screws are factory-set your new thermostat for your type of the thermostat to maintain accurate temperature control, minimize swings in degrees Fahrenheit...

Owner's Manual - Page 7

... the old wires to the new thermostat. c. Loosen the terminal screws and slip each wire beneath its matching terminal (Fig 10). Securely tighten the terminals. 69-0653-6 END OF WIRE VISIBLE HERE M20126 INSTALLATION 7 b. Hold the thermostat as a 90% or greater AFUE (Average Fuel Utilization Efficiency) unit Hot water boiler Electric furnace Screws A and B Use factory setting...

Owner's Manual - Page 8

Honeywell recommends using Energizer® batteries. Install the batteries. Go to latch the bottom of the case to page 12. 69-0653-6 Align the tabs at the top of the thermostat with the tabs at the top of the thermostat and heating/cooling system. Install the batteries Fig. 13 Fig. 14 M1719C REMOVING BATTERY DOOR 8 INSTALLATION M20131...

Owner's Manual - Page 9

... electrical circuit. d. f. Wrap the wires separately, using electrical tape to avoid damaging your old thermostat, do not connect to the old thermostat If there are extra wires that are not used during the installation of the new thermostat. c. Continue with the installation as instructed on page 4, step 2e. Locate the wires that do not label them...

Owner's Manual - Page 10

... (Y2). You have a single stage heat pump or zoning system. You have a multistage heating/cooling system. Fig. 15 JUMPER (FACTORY- Old thermostat terminal Connect to wire the new thermostat. Five wires connected to the old thermostat Your new thermostat has a factory-installed metal jumper between R and Rc terminals in heat (B terminal). See page 2 for an alternate...

Owner's Manual - Page 11

...1 Fan switch-Selects automatic fan operation or fan on (page 17) 9 2 Set Schedule-Puts the thermostat into programming 10 mode (page 14) 11 3 Set Clock/Day-Sets the clock and day (page ...page 19) 11 Temp Warmer and Cooler-Sets the temperature warmer and cooler (page 14) 12 Run Program-Returns thermostat to normal operating mode 13 Hold Temp-Holds a selected temperature (page 19) 14 System switch...

Owner's Manual - Page 12

Press and hold or until the current time is displayed. Learn about the programming features Your 3200 thermostat allows you will be lower and the energy-saving temperature higher. Fig. 17 b. The time is displayed (Fig. 18). Press once. The program periods are ...

Owner's Manual - Page 13

... programmed for this period. You can set up and get up an energy-saving temperature for this period. If you decide not to program your thermostat, it will remain in effect until you are regularly away from home. Program period WAKE LEAVE RETURN SLEEP Description The time when you get ready...

Owner's Manual - Page 16

... setting is 10°F (6°C) below room temperature. Press until the setting is changed, the thermostat may delay up to 5 minutes before turning on the air conditioner. Press until the setting is 10...Set the System switch to HEAT, and the Fan switch to COOL. Your heating system should run after a short delay. Set the System switch to AUTO. through 3k. Your heating system ...

Owner's Manual - Page 17

...fan runs continuously. Set the System switch to OFF and the Fan switch to the G terminal on the bottom of the thermostat faceplate (Fig. 16 page 11) control the operation of the thermostat. ...then set the System switch. A two-speed fan usually runs on high with the air conditioner and on automatically with the furnace. The time is displayed. Press and hold or until ...

Owner's Manual - Page 18

.... If you will not have to reprogram. Switch System Setting Result Cool The thermostat controls your heating system. Steady "bAt Lo" Blank display Almost dead Replace the batteries immediately. b. d. Note: If you insert the new batteries within the month. e. c. Install the new batteries. Note: If "bAt Lo" continues to display after replacing the batteries...

Owner's Manual - Page 21

... the batteries backwards for five to reset the thermostat. Reprogram if necessary. • Check that the AM and PM indications are fresh and installed correctly. • Set the System switch to come on . • You have reached the temperature limit. replace them backwards for the furnace to heat up and the fan to OFF...

Owner's Manual - Page 22

... under the battery cover) • Type of heating/cooling system (hot water, warm air, oil, gas, etc.) • Number of the thermostat as instructed on • • • • • • The house is too warm or too cool • • The furnace cycles too frequently • or the system cycle length is too...

Owner's Manual - Page 23

...limitation may have any time during the warranty period, the product is defective or malfunctions, Honeywell shall repair or replace it is defective, (i) return it, with proof of purchase (...or limitation of incidental or consequential damages, so this warranty, please write our Customer Relations Center, Honeywell Inc., 1885 Douglas Dr. N., Golden Valley, MN 55422-3992, or call 1-800-468-...

Owner's Manual - Page 24

Home and Building Control Honeywell 1985 Douglas Drive North Golden Valley, MN 55422 69-0653-6 Rev. 9-01 Home and Building Control Honeywell Limited-Honeywell Limitée 35 Dynamic Drive Scarborough, Ontario M1V 4Z9 Printed in the U.S.A. www.honeywell.com/yourhome