Honeywell CT3200 Support Question
Honeywell CT3200 Support Question
Find answers below for this question about Honeywell CT3200.Need a Honeywell CT3200 manual? We have 1 online manual for this item!
Question posted by sdceasyg on August 7th, 2014
Honeywell Thermostat Ct3200- Cooling Does Not Come On
The person who posted this question about this Honeywell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by BusterDoogen on August 24th, 2014 1:44 PM
BusterDoogen
Member since:
October 30th, 2011 Points: 28,565,407
Member since:
October 30th, 2011 Points: 28,565,407
Cooling does not come on • Check that the System switch is set to Cool.
• Check the system fuse or circuit breaker and replace or reset if necessary.
• Check for correct wiring and good connections.
• If display is blank or says “bAt Lo,” install fresh batteries.
• The thermostat has a built-in time delay on cooling. Allow 5-10 minutes after changing setting before air conditioner starts.
• If temperature setting is lower than room temperature and SYSTEM ON arrow is displayed, thermostat is operating correctly. Contact ac contractor.
I hope this is helpful to you!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you
Related Honeywell CT3200 Manual Pages
Owner's Manual - Page 1
... our home expert Web site at www.honeywell.com/yourhome or call Honeywell Customer Relations at 1-800-468-1502. MagicStat® CT3200 Programmable Thermostat
Installation and Programming Instructions
Weekday/Weekend (5-day/2-day) Programmable Heat and/or Cool Low Voltage (20 to 30 Vac) Thermostat and Mounting Plate Model CT3200
Welcome to the world of Contents
Installation
2
Programming...
Owner's Manual - Page 2
... waste management authority for instructions regarding recycling and the proper disposal of thermostat is right for your heating/cooling system. Multistage Heat Pump Heating and cooling are produced from the same outdoor unit (compressor) with the CT3200, the table recommends an alternate Honeywell model. Steam A steam boiler with more than one stage. Compatible Alternate with...
Owner's Manual - Page 3
Make sure that your new thermostat. IMPORTANT: To avoid damaging the compressor in the air conditioner, do not operate the cooling system when the temperature outdoors is ... your heating and cooling systems are working properly. Gather the needed tools and supplies listed below 50°F (10°C).
69-0653-6
INSTALLATION 3
If there is below . Honeywell recommends Energizer®...
Owner's Manual - Page 4
... now look like Fig. 4.
69-0653-6 Unscrew and remove the old thermostat's mounting plate from falling back into the wall. Inspect the old thermostat wiring. Disconnect the wires from the old thermostat and wrap the wires around a pencil to the heating/cooling system, either at the furnace or at the fuse/circuit breaker panel...
Owner's Manual - Page 5
... (Fig. 6). e. f.
d.
Position the mounting plate on the wall and should look like Fig. 7.
69-0653-6
Y
G Rc
RW
M20128
INSTALLATION 5 Separate the mounting plate from the thermostat using a coin, as shown in drywall, gently tap the anchors that were provided into each of the mounting plate's screw holes. c. g. Install the mounting plate...
Owner's Manual - Page 6
... SWITCH POSITION
D
WARM AIR A-IN B-IN
F
FURNACE
HOT WATER A-OUT B-IN
F
BOILER 1 TURN
ELECTRIC A-IN B-OUT
E
FURNACE
1 TURN
W Y G
R
Rc
FUEL SWITCH
M20145
IMPORTANT: Setting your thermostat correctly for your heating system uses: F-gas or oil, or E-electricity.
To install the batteries, see the instructions that your type of heating system allows...
Owner's Manual - Page 7
...WIRE VISIBLE HERE
M20126
INSTALLATION 7 Using the labels on the wires, match the letter of your old thermostat wire with an efficiency rating under 90%. (The furnace efficiency rating should be on the back of ... each wire beneath its matching terminal (Fig 10). Type of your new thermostat.
Heating System Table Note: Setting the screw "out one turn" means turning the screw 360° counter...
Owner's Manual - Page 8
... tabs at the top of the thermostat and heating/cooling system. Replace the battery door. The flashing continues until you begin to program the thermostat. You are installed correctly, the digital display flashes all entries once, then begins to flash a default time and the current temperature (Fig. 14). Honeywell recommends using Energizer® batteries...
Owner's Manual - Page 9
...to the clock terminals marked C or C1.
Wires that are not connected to the old thermostat If there are extra wires that are not used during the installation of a heat pump or...page 4 at step 2e.
c.
Three thermostat wires If you have a three-wire heating-only system and cannot operate the fan using electrical tape to the heating/cooling system is most likely a variation of...
Owner's Manual - Page 10
Remove the jumper before wiring the R and Rc terminals.
Power Power for cooling Heat
Cooling
Fan Changeover in cool (O terminal) or changeover in 5-wire systems.
10 INSTALLATION
69-0653-6 You have a multistage heating/cooling system. Five wires connected to the old thermostat Your new thermostat has a factory-installed metal jumper between R and Rc terminals in heat (B terminal...
Owner's Manual - Page 11
... clock/Day
Ahead
Warmer
Run Program
2
Set Schedule
Back
Cooler
Hold Temp
1
Fan
Auto On
System
Cool Off Heat
Descriptions
1 Fan switch-Selects automatic fan operation or fan on
(page 17)
9
2 Set Schedule-Puts the thermostat into programming
10
mode (page 14)
11
3 Set Clock/Day-Sets the clock and day (page...
Owner's Manual - Page 12
... (Fig. 19).
Learn about the programming features
Your 3200 thermostat allows you to program schedules for both a heating season and a cooling season. • During the heating season, you can set... higher and the energy-saving temperature lower. • The reverse is true during the cooling season-the normal room temperature will want to two program periods for the weekends (Saturday...
Owner's Manual - Page 13
...
LEAVE RETURN
SLEEP
Description
The time when you get up and get ready to leave your thermostat, it will remain in effect until you decide not to program weekend schedules, the temperature ... is programmed for the weekday SLEEP schedule will automatically control heating at 68°F (20°C), and cooling at 78°F (26°C), 24 hours a day. You can set the system at a comfortable...
Owner's Manual - Page 15
... j. k.
Press
again to set
the program. to display a blank schedule for your cooling schedule.
Write in the times and temperatures that you want to start the program.
until... Sunday WAKE temperature by pressing
or
until the desired temperature
j. Press (Fig. 23).
Cooling Schedule
Suggested Settings
Weekday (Mon-Fri)
Weekend (Sat-Sun)
Program period
Time Temp Time...
Owner's Manual - Page 16
...;C) below room
temperature. Repeat steps 3c. b.
Press
until the setting is changed, the thermostat may delay up to 5 minutes before turning on the air conditioner. Set the System switch to COOL, and the Fan switch to AUTO.
Your cooling system and fan should start and the fan should run after a short delay. c. Set...
Owner's Manual - Page 17
... (Fig. 16 page 11) control the operation of the thermostat.
69-0653-6
OPERATION 17 Auto is 10°F (6°C) above room
temperature. The fan runs continuously. Operation Change the clock for more efficient air cleaning. Press
until the correct time is displayed. The cooling system and fan should stop. A two-speed fan...
Owner's Manual - Page 18
... before leaving to prevent the system from shutting down due to reprogram. Switch System
Setting Result Cool The thermostat controls your heating system. Replace the batteries
As the batteries run low, your thermostat shows the following in the thermostat. Press on the left side of battery power in the digital display:
If you will...
Owner's Manual - Page 19
....
Override the program settings
Note: Make sure the System switch is set to either HEAT or COOL before the
next scheduled program period, press
. To cancel the temporary change is reached.
a.
... next scheduled program
period is temporary (Fig. 27). The heating/cooling schedule that the change before making any changes to the schedule. until the desired temperature is displayed (...
Owner's Manual - Page 21
...batteries backwards for the period in question. The display should come on .
• Check the program times for five to reset the thermostat. The setting range is operating correctly. See page 18 ...shows flashing or steady "bAt Lo"
Temperature change occurs at the wrong times
Heating will not come on
Then...
• Make sure the batteries are correct. Reprogram if necessary.
• ...
Owner's Manual - Page 22
... Cooling will not come on cooling. The thermostat has a built-in the wall behind the mounting plate with Canadian Radio Interference Regulations, CRC c.1374.
22 FREQUENTLY ASKED QUESTIONS
69-0653-6
Be aware that might adversely affect thermostat operation. Customer assistance For all questions concerning this thermostat, please read and follow the instructions. If you call Honeywell...
Similar Questions
Where Is Reset Button Honeywell Thermostat Ct3200 Manual
(Posted by Camce 9 years ago)
How To Prgram The Thermostat To Cool It Is A Honeywell Ct 3200
(Posted by Peminn 9 years ago)
