Honeywell CT3200 Support Question
Honeywell CT3200 Support Question
Find answers below for this question about Honeywell CT3200.Need a Honeywell CT3200 manual? We have 1 online manual for this item!
Question posted by Camce on September 13th, 2014
Where Is Reset Button Honeywell Thermostat Ct3200 Manual
The person who posted this question about this Honeywell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Honeywell CT3200 Manual Pages
Owner's Manual - Page 1
... Customer Relations at 1-800-468-1502. Registered Trademark Copyright © 2001 Honeywell • All Rights Reserved
69- 0653- 6 Your new thermostat will automatically control the temperature in your new Honeywell MagicStat® Programmable Thermostat. MagicStat® CT3200 Programmable Thermostat
Installation and Programming Instructions
Weekday/Weekend (5-day/2-day) Programmable Heat and...
Owner's Manual - Page 2
... local waste management authority for instructions regarding recycling and the proper disposal of thermostat is right for your system is the right thermostat for
240 volts
No
CT3600
No
CT3600
No
CT3611
No
See your heating/cooling system.
Multistage Conventional A heating or cooling system with the CT3200, the table recommends an alternate Honeywell model.
Owner's Manual - Page 3
...°C).
69-0653-6
INSTALLATION 3 Required tools and supplies
Optional tools
• Two AA alkaline batteries. Make sure that your new thermostat. Carefully unpack your heating and cooling systems are working properly. Honeywell recommends Energizer® • Wire cutter/stripper or sharp knife
batteries.
• Level
• Screwdriver
• Electrical tape
• Hand...
Owner's Manual - Page 4
... it .
Disconnect the wires from the old thermostat and wrap the wires around a pencil to on page 9. • The old thermostat is a clock thermostat with the letter of the following conditions, see... wires attached to C or C1 terminals. • The old thermostat has 3 wires. • There are 5 wires connected to the old thermostat. • There are extra wires that are not connected to the...
Owner's Manual - Page 5
... wall. Position the mounting plate on the wall and should look like Fig. 7.
69-0653-6
Y
G Rc
RW
M20128
INSTALLATION 5
f. Separate the mounting plate from the thermostat using a coin, as shown in drywall, gently tap the anchors that were provided into each of the drilled holes or anchors (Fig. 6). d. If installing in...
Owner's Manual - Page 6
... system allows it to display the temperature in degrees Celsius (°C), adjust screw C out one turn.
Step 4. b. Note: These screws are factory-set your new thermostat for your type of fuel that begin on the next page to display the temperature in the temperature of heating system. c. F POSITION
FUEL SWITCH
F
E
C
ADJUST...
Owner's Manual - Page 7
...
Fig. 9
G Y W
R
Fig. 10
5/16 in Fig. 9. b. Loosen the terminal screws and slip each wire beneath its matching terminal (Fig 10). Hold the thermostat as a 90% or greater AFUE (Average Fuel Utilization Efficiency) unit Hot water boiler
Electric furnace
Screws A and B
Use factory setting A-leave in B-leave in
A-out ...
Owner's Manual - Page 8
...to flash a default time and the current temperature (Fig. 14). Go to program the thermostat. Install the batteries
Fig. 13
Fig. 14
M1719C
REMOVING BATTERY DOOR
8 INSTALLATION
M20131
IMPORTANT...progress When the batteries are now ready to latch the bottom of the thermostat (Fig. 12). Honeywell recommends using Energizer® batteries. Using a coin, open the battery door as marked inside ...
Owner's Manual - Page 9
... the wires. As you have three wires for installation assistance.
Wrap the wires separately, using the fan ON switch, the 3200 thermostat will not interfere with the operation of the new thermostat.
You will not interfere with the installation as instructed on page 4, step 2e.
Continue with the operation of the new...
Owner's Manual - Page 10
... (W2, H2) or second stage cooling (Y2). Remove the jumper before wiring the R and Rc terminals.
Power Power for an alternate thermostat model. Old thermostat terminal
Connect to wire the new thermostat. See page 2 for cooling Heat
Cooling
Fan Changeover in cool (O terminal) or changeover in 5-wire systems.
10 INSTALLATION
69-0653-6
Transformer...
Owner's Manual - Page 11
...1 Fan switch-Selects automatic fan operation or fan on
(page 17)
9
2 Set Schedule-Puts the thermostat into programming
10
mode (page 14)
11
3 Set Clock/Day-Sets the clock and day (page ...11 Temp Warmer and Cooler-Sets the temperature warmer and cooler (page 14)
12 Run Program-Returns thermostat to normal operating mode
13 Hold Temp-Holds a selected temperature (page 19) 14 System switch-Selects...
Owner's Manual - Page 12
...
displayed.
The program periods are
displayed (Fig. 19). Press and hold
or
until the current time is
displayed.
Learn about the programming features
Your 3200 thermostat allows you to two program periods for the weekends (Saturday and Sunday).
The day is true during the cooling season-the normal room temperature will...
Owner's Manual - Page 13
The time between returning home and going to program your thermostat, it will remain in effect until you get up and get ready to program times and... you are regularly away from home. You can set any higher than 45°F (7°C). • When pressing the buttons, use the ball of sharp fingernails or pencil points
can set up an energy-saving temperature for this period. The time ...
Owner's Manual - Page 16
... system and fan should shut off. e. Set the System switch to HEAT, and the Fan switch to COOL. Press
until the setting is changed, the thermostat may delay up to 5 minutes before turning on the air conditioner. This delay protects the compressor.
16 PROGRAMMING
Fig. 25
Fig. 26
69-0653-6 c. Check...
Owner's Manual - Page 17
... furnace. c.
f. Set the Fan and System switches
The switches on low with the air conditioner and on the bottom of the thermostat faceplate (Fig. 16 page 11) control the operation of the thermostat.
69-0653-6
OPERATION 17
Auto is 10°F (6°C) above room
temperature.
Press
until the correct time is displayed.
Owner's Manual - Page 18
... the batteries before leaving to prevent the system from shutting down due to reprogram the thermostat.
Make sure that the positive and negative terminals are : You should:
Flashing "bAt... operating. Install the new batteries. Replace the batteries
As the batteries run low, your thermostat shows the following in the OFF position. Steady "bAt Lo" Blank display
Almost dead Replace...
Owner's Manual - Page 21
...to come on before checking
for the furnace to heat up and the fan to reset the thermostat. Replace the batteries correctly. Be sure that the System switch is set the System... temperature setting is higher than the current room temperature and
the SYSTEM ON arrow is displayed, the thermostat is 45°F-88°F (7°C-31°C).
• The batteries are correct. The display...
Owner's Manual - Page 22
... and replace or reset if necessary. Check for instructions. If the temperature setting is lower than the current room temperature and the SYSTEM ON arrow is displayed, the thermostat is blank or ...Adjust the screws on the back of wires connected to the thermostat
NOTICE: This equipment is normal for assistance. If you call Honeywell Customer Relations at 1-800-468-1502, Monday-Friday, 7:...
Owner's Manual - Page 23
...the product was caused by the consumer. THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF... Central Time.
MN10-3860 1885 Douglas Drive North Golden Valley, MN 55422-3992
Honeywell Canada: Honeywell Limited/Honeywell Limitée 35 Dynamic Drive Scarborough, Ontario M1V 4Z9
This warranty does not ...
Owner's Manual - Page 24
www.honeywell.com/yourhome Home and Building Control Honeywell 1985 Douglas Drive North Golden Valley, MN 55422
69-0653-6 Rev. 9-01
Home and Building Control Honeywell Limited-Honeywell Limitée 35 Dynamic Drive Scarborough, Ontario M1V 4Z9
Printed in the U.S.A.
Similar Questions
How To Reset Your Thermostat
I'm having a problem with my thermostat it's got cooling off heat an only working on E M Heat would ...
I'm having a problem with my thermostat it's got cooling off heat an only working on E M Heat would ...
(Posted by Quintinmoore48 3 years ago)
Honeywell Thermostat Ct3200- Cooling Does Not Come On
(Posted by sdceasyg 9 years ago)
Magicstat Ct3200 Programmable Thermostat How To Switch To Celsius
(Posted by f1fKE 10 years ago)