Hitachi NR83A2 Support Question

Find answers below for this question about Hitachi NR83A2 - 3.25" Full Head Framing Strip Nailer.
Need a Hitachi NR83A2 manual? We have 2 online manuals for this item!

Hitachi Overview Questions Manuals Reviews Videos Research

Question posted by norcaladams77 on August 23rd, 2015

Ribbon Spring

How do I installed a ribbon spring in a Hitachinr83a2 nail gun

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by techyagent on August 25th, 2015 10:37 AM

This answer was accepted by the poster of the original question.

techyagent

Member since:
June 17th, 2014

Points: 4,799,790

1,090
points

To install a ribbon spring you have to click here

Thanks

Techygirl

Related Hitachi NR83A2 Manual Pages

Instruction Manual - Page 3

... next, pull the trigger to continue driving nails. - 3 - First, pull the trigger; EXPLANATION OF THE NAILING ACTION OF THE HITACHI NAILER ⅜ SINGLE ACTUATION MECHANISM (SINGLE SEQUENTIAL... a nail will not be avoided by recognizing a potentially hazardous situation before operating or maintaining this Manual. English IMPORTANT SAFETY INFORMATION Read and understand tool labels and...

Instruction Manual - Page 4

...contains fasteners or not. Respect the Nailer as the Nailer can lead to protect your head from loud noise. ALWAYS WEAR EAR AND HEAD PROTECTION. Always wear head protection to the requirements of American ... OPERATION." (pages 13 - 14) 6. NEVER POINT TOOL AT YOURSELF OR OTHERS IN WORK AREA. Never carry the Nailer with the Nailer. OPERATORS AND OTHERS IN WORK AREA MUST WEAR SAFETY ...

Instruction Manual - Page 5

... loading fasteners into and through or away from the firing head. Never place your hands or feet closer than 8 inches... with the Nailer at too steep of an angle; PLACE NAILER PROPERLY ON WORKPIECE. This Hitachi nailer includes a nailing operation switching ... 14. English SAFETY - Avoid the risk of unnecessary tools, debris, furniture, etc. 10. Lock the storage area. 9....

Instruction Manual - Page 6

... and personnel performing maintenance. 2. STAY ALERT. Use common sense. and do not drop the Nailer or strike the Nailer against hard surfaces; English SAFETY - Continued WARNING 25. NEVER USE NAILER WHICH IS DEFECTIVE OR OPERATING ABNORMALLY. DISCONNECT AIR HOSE FROM NAILER WHEN: 1) doing . and 6) handing it immediately and arrange for better and safer performance. 34...

Instruction Manual - Page 7

...ACTUATION MECHANISM (Switching device: upward position) CONTACT ACTUATION MECHANISM (Switching device: downward position) Piston Piston O-Ring Driver Blade Nose Adjuster [ ] Only NR83A2 (with depth adjustment) Push Lever Valve part Trigger Switching Device Valve Bush Body Cap Air Plug (Sold separetely) Ribbon Spring Stop Lever Nail Feeder Magazine Assembly Outlet (Firing Head) - 7 -

Instruction Manual - Page 8

... driven with this Nailer. Plastic-collated strip nails Full-head nails Min. .286" (7 mm) Max. .3" (7.6 mm) 2" (50 mm) 3-1/4" (83 mm) .113" (2.9 mm) .131" (3.3 mm) ACCESSORIES WARNING ⅷ Accessories other nails can lead to serious injuries. The use only the genuine HITACHI nails for M5 screw 1 - 8 - Only nails shown in the Table below can result in tool malfunction and/or...

Instruction Manual - Page 9

...Sequential Actuation Mechanism kit (Sequential Trip Mechanism kit) (Code No. 884069) ⅜ Pneumatic Tool Lubricant .8 oz. (25 cc) oil feeder (Code No. 877153) 4 oz. (120 cc) oil feeder (Code...Nailer and extend the Nailer life. These units should always be installed as a power source for safe operation of the maximum pressure produced in compressed air. Use Hitachi pneumatic tool...

Instruction Manual - Page 10

... 4.5 kgf/cm2). 2 Remove all nails from the Nailer. 3 Connect the air hose and free-fire (blank-fire) the Nailer. CAUTION ⅷ Do not free-fire the Nailer at 100 psi driving 30 nails per minute Amount of Hitachi pneumatic tool lubricant into the air plug on the Nailer twice a day. TESTING THE NAILER DANGER ⅷ Operators and others...

Instruction Manual - Page 11

... psi (8.3 bar 8.5 kgf/cm2). The correct air pressure is observed, you may load nails in the Nailer. With the Nailer off the workpiece, pull the trigger. Next, point the nailer downward, pull the trigger and then wait in the Nailer. Using the Nailer at recommended operating pressure 70 - 120 psi (4.9 - 8.3 bar 5 - 8.5 kgf/cm2) according to the...

Instruction Manual - Page 12

... it latches. Stop Lever Nail Feeder The Nailer is set under the nail stopper of nail feeder. Tail Nail Nail Stopper Magazine (3) Press the stop lever and slide the nail feeder forward until it contacts the nail strip. NAILER OPERATION Read section titled "SAFETY"(pages 4 - 6). Two strips can be loaded at least 5 nails remaining. ⅷ Set heads of tail nail is now ready to...

Instruction Manual - Page 13

... ricochet and hurt someone . ⅷ Never drive nails from firing head when using. ⅷ Do not drive nails on the workpiece with Nailer at the same time. next, pull the trigger to drive the nail. METHODS OF OPERATION This Nailer is equipped with this Hitachi nailer will drive a nail each time the push lever is not in the...

Instruction Manual - Page 14

...the push lever will not operate properly.) 2 Pull the trigger with the Nailer off the trigger except during a nail driving operation. Valve Bush Switching Device 1 Downward position WARNING ⅷ Keep...8567; Some types of loaded nails can spark out of Hitachi pneumatic tool lubricant into the air plug on the air compressor tank to drive a nail. 4 Move the Nailer along the workpiece with a...

Instruction Manual - Page 15

... depth, be sure that: 1) the air pressure to the Nailer remains constant (regulator is installed and working properly), and 2) the Nailer is reached for the adjuster. - 15 - ADJUSTING THE NAILING DEPTH [Only NR83A2 (with depth adjustment)] WARNING ⅷ Disconnect the air hose from the nailer before turning the adjuster. English Perform a nailing test. 5 DISCONNECT AIR HOSE FROM...

Instruction Manual - Page 16

WARNING ⅷ Disconnect air hose and remove all nails from normal use. Maintenance chart (See page 17) 5. Storing ⅜ When not in use , the Nailer should be stored in a warm and dry place. B: Code No. C: No. MODIFICATIONS: Hitachi Power Tools are subject to incorporate the latest technological advancements. code numbers and/or design) may...

Instruction Manual - Page 17

... air hose. Slow to normal flow. Intermittent feed. CHECK METHOD Check for proper nails. Check function of filter with Hitachi pneumatic tool lubricant. Ribbon spring weakend or damaged? Check for a jam. Check for replacement. Check inside diameter of lubricant into the Nailer. Increase air pressure. (Do not exceed 120 psi (8.3 bar 8.5 kgf/cm2).) Use Hitachi...

Parts List - Page 2

... 1 7 877-328 EXHAUST PIECE 1 8 877-854 GASKET (C) 1 9 884-110 EXHAUST VALVE (ORANGE) 1 10 877-307 HEAD CAP AND GASKET SET 1 INCLUD. 8 11 877-368 O-RING (1AP-48) 1 12 877-323 PISTON 1 13 877-316...CYLINDER RING 1 20 877-321 CYLINDER SPRING 1 21 877-322 BASE WASHER 1 22 877-310 CYLINDER GUIDE 1 23 877-327 GASKET (G) 1 24 884-069 WARNING LABEL 1 25 883-506 BODY ASS'Y 1 INCLUD...

Parts List - Page 3

... 1 TRIGGER VALVE BUSHING 1 TRIGGER PLUNGER 1 PLUNGER O-RING 1 ROLL PIN D3X30 (10 PCS.) 1 VALVE SLEEVE (A) 1 O-RING (S-7) 1 PLUNGER O-RING 1 WASHER M5 (10 PCS.) 1 PLUNGER (B) SPRING 1 PLUNGER (B) 1 NAIL FEEDER 1 RIBBON SPRING 1 NEEDLE ROLLER 1 NYLON NUT M4 1 SPRING WASHER M4 (10 PCS.) 1 NYLON NUT M5 1 SPRING WASHER M5 (10 PCS.) 1 MAGAZINE 1 SLEEVE 1 HEX.

Parts List - Page 4

... 5MM 503 944-458 HEX. DESCRIPTION 601 881-768 GRIP TAPE (A) 602 880-407 TAPE 603 877-153 PNEUMATIC TOOL LUBRICANT (30CC) 604 874-042 PNEUMATIC TOOL LUBRICANT (120CC) 605 876-212 PNEUMATIC TOOL LUBRICANT (1L) 606 317-918 GREASE (ATTOLUB NO.2) 500G NO. DESCRIPTION 501 872-422 HEX. CODE NO. USED 1 1 1 1 1 1 REMARKS...