GE NX-148E Support Question
GE NX-148E Support Question
Find answers below for this question about GE NX-148E - Security NetworX LCD Keypad.Need a GE NX-148E manual? We have 1 online manual for this item!
Question posted by carldoucette on August 10th, 2011
What Will Happen If 2 Keypads Have The Same Number As Its Identification?
we had a system that was set in 2 partitions and 5 keypads entered as follows
1-1
2-1
3-1
1-2
2-2
Would this cause bus errors?
Current Answers
Related GE NX-148E Manual Pages
User Manual - Page 2
... battery condition.
5 FUNCTION KEYS
The door (not shown) is detachable and can be applied on the keypad door for the Emergency Activation keys that are programmed to work with your system.
COMMERCIAL FIRE SYSTEM LCD KEYPAD
Model NX-148E-CF
READY light is "on" when the system is ready to arm, flashes if ready to...
User Manual - Page 5
EVENT LOG 25 EMERGENCY EVACUATION PLANS 27
NX-148E-CF
3 TABLE OF CONTENTS
GLOSSARY OF TERMS 4 UNDERSTANDING THE LIGHTS 6 KEYPAD FUNCTIONS 7
Arming Your System In The "... Of The LCD 17 Setting The System Clock 18 Using The Door Chime Feature 18 PARTITIONED SYSTEMS OPERATION 19 Lights In Partitioning Master Mode 19 Displays In The Partitioning Master Mode 19 KEYPAD CONTROL TONES ...
User Manual - Page 6
...INSTALLING COMPANY.
4
NX-148E-CF FAILURE TO DO SO COULD RESULT IN THE SECURITY SYSTEM NOT WORKING PROPERLY. READ THE ENTIRE MANUAL AND, IF POSSIBLE, PRACTICE ON THE KEYPAD CONTROL WHILE YOUR ... the status of an alarm event. 5.
YOU SHOULD BE AWARE OF THE FOLLOWING FACTS WHEN PREPARING A SAFETY/SECURITY PLAN FOR YOUR HOME/BUSINESS.
1. Your system should be Disarmed using a 4 or 6 digit ...
User Manual - Page 7
...security system by pressing either User Codes (relating to a person) or Function Codes (a toggle switch to turn specific functions on the keypad control (for Entry/Exit doors, or grants a delay to allow someone to enter...Code:
A master arm/disarm code that has been programmed by the installing company. Partitioned System: A system divided into multiple areas in reporting to arm or disarm the...
User Manual - Page 8
....
Entering a code followed by pressing the [STAY] key when the system is armed.
6
NX-148E-CF...LCD display will flash if the system has a low battery condition. Bypass Light
The bypass light is "on .
The armed light is "off " when the system is not ready to arm because of the exit delay as a warning that a fire zone is in this keypad's partition is bypassed. It will cause...
User Manual - Page 10
...secure. Ready light must be on or flashing. NOTE: If any zone (s) have an entry delay. If the power light is enabled, if you have an entry
System Armed Instant
delay.
8
NX-148E...corresponding to arm
Step 2
Enter your 4 or 6 digit user code. (Optional, if programmed.) If "Auto Bypass" is enabled, all interior zones will illuminate if any zone(s) are as follows:
Step 1
Close all ...
User Manual - Page 11
...and will allow the user to turn on the LCD display. Type code to leave the building. ... duration of the designated Entry/Exit doors, the keypad control will stop. The system can be created if...security system. This feature is now DISARMED.
If all designated interior zones.
The "Instant" message will extinguish. Step 1 Step 2
Enter a valid user code. The security...
User Manual - Page 12
... LCD prompts for zone 112.)
Step 5 Step 6 Step 7
Press the [BYPASS] key again.
Press the [BYPASS] key again OR press # to bypass, use the following:
Step 1 Press the [BYPASS] key. If a code is entered followed by the [CANCEL] key during an abort delay time. Entering a code followed by the [CANCEL] key while this viewing mode.
10
NX-148E...
User Manual - Page 14
...security system will scroll automatically. NOTE: Some Panic/Hold-Up alarms are installer level functions.
Hint: If you can activate the auxiliary alarm by the function number...programmed, you already know the function numbers simply press [r] followed by pressing the Emergency Activation [... 90=Log Review
91=View Settings 97=Set Date/Time
12
NX-148E-CF Auxiliary Key - Each time...
User Manual - Page 15
...Keypad is performed, enter a user code to lower tones. to adjust the keypad Lower tone
º
sounder to silence the siren.
Step 2 If the siren test is now in which case a test signal will be sent. NX148E-CF
13
SETTING THE KEYPAD... alarm memory. Step 2
The LCD Screen will display the zone status.
VIEW ZONE STATUS
Step 1 Press r • . The LCD
Screen will perform a battery test...
User Manual - Page 16
... turn the X-10 device "On" or press the - The LCD keypad is pressed.
Step 2 Press any other function mode before attempting to "Select Light Number 0 - 9".
to switch between the two languages programmed in your keypad. Step 2 Repeat Step 1 to revert to control. Step 2 Enter the number of the display it will prompt you to control up...
User Manual - Page 17
....
The LCD keypad will now prompt you for that individual.
Assign user codes before assigning authority levels.
Step 3 Enter the 2-digit user number. The LCD will display the current code for a user number.
Step 2
Enter [master code]. NOTE: For partitioned systems, if you must have access to all partitions, or at least all of the partitions to users by following chart...
User Manual - Page 18
...function is not already disarmed. Enter your installer.
16
NX-148E-CF Wait a few minutes and repeat step 2 to the prompt for the next user code. If the keypad still beeps after repeated attempts, ... a partition, press the partition number on the LCD screen, press the [r] key until you entered in Step 3.
Open / Close Rprt? Master code? Step 5 Press [r] to save the data. The LCD will...
User Manual - Page 20
... will toggle the chime feature on/off and produce a momentary ding-dong sound.
18
NX-148E-CF Each press of week, date, month, and year. scroll keys to the minutes...Enter r 9 7 . Step 3 Use the • - If the chime is turned on , the chime light will be illuminated. Step 5 Repeat Steps 3 and 4 until the entire time and date are set.
The LCD Screen will prompt for a code. Step 2 Enter...
User Manual - Page 21
...NX-8 control panel. NOTE: r 1 will flash if the system has a low standby battery condition.
It will temporarily access the Master Mode. DISPLAYS IN THE PARTITIONING MASTER MODE
ARMED and READY STATUS
The LCD screen will be displayed from your partitioning... code is not " partitioned. NX148E-CF
19 PARTITIONED SYSTEMS OPERATION
This system is " is entered followed by using the screen ...
User Manual - Page 22
... arm/disarm authority for possible conditions. ARMING AND DISARMING MULTIPLE PARTITIONS
To arm/disarm multiple partitions, enter a code that are Ready, and Area 5 is disarmed. Refer to the following display will arm it.
To arm all interior zones in the exit delay. The following section.
20
NX-148E-CF For example: If Area 4 is armed, [r] [4] will appear...
User Manual - Page 23
... with the word "Area #". The word "System" will affect this feature.
The following is selected. To operate an individual area, enter the number of this individual partition only. To exit this code will now operate as a single area keypad. All keys and functions entered will be silenced by this screen, press [#]. OPERATING INDIVIDUAL AREAS IN THE...
User Manual - Page 24
... change when entering a code to indicate telephone line fault if selected. The arm/disarm state of the following reasons:
Beeps for the 'CHIME" feature.
Sounds a continuous tone during an exit delay; Pulses when a FIRE zone has a trouble condition. Pulses when one or more of your installer if a trouble condition exists.
22
NX-148E-CF
User Manual - Page 26
... applicable to the control. A wireless device has a low battery. Press [r] to identify the zone.
24
NX-148E-CF A zone is experiencing some form of trouble on . Press [r] to identify the tampered zone.
An ... identify the zone. A zone is not reporting to all controls.)
An expansion device or keypad is not on the bell or siren circuit.
Press [r] to identify the zone.
Expansion...
User Manual - Page 27
... or speaker tamper has been detected.
Close
Reports user number, date, time and partition of a power supply has occurred.
Zone Lost
A wireless or multiplexed zone device is not reporting to the control.
Old events will be pushed out as new ones enter the log. Exit Error
Entry/Exit zone was armed.
Recent Close An...
Similar Questions
Nx-148e Lcd Keypad How To Change Master Code
(Posted by Loriljahan 9 years ago)
How To Get Rid Of Function Errors On A Nx-148e Lcd Keypad
(Posted by brmn 10 years ago)
Where Can I Buy A Swing Down Door Replacement For A Ge Nx-148e Lcd Keypad?
I have owned the security system since 2007. It appears to not have changed by looking at the new on...
I have owned the security system since 2007. It appears to not have changed by looking at the new on...
(Posted by btestrake 10 years ago)
Where Is The Battery Located In My Nx-148e Lcd Alarm System
(Posted by PraGoodCh 10 years ago)
Ge Networx Nx 148e Security System
Just bought a foreclosed home & it has two security system panels, one on each level. I do not k...
Just bought a foreclosed home & it has two security system panels, one on each level. I do not k...
(Posted by Meadowsa 10 years ago)