Home » Garmin » Marine GPS » Garmin GSD 26

Garmin GSD 26 Support Question

Find answers below for this question about Garmin GSD 26.
Need a Garmin GSD 26 manual? We have 1 online manual for this item!

Garmin Overview Questions Manuals Reviews Videos Research

Question posted by Ebiliosa on December 19th, 2016

Wiring Problem Gsd 26 Sounder

when removing the cover of a GSD 26 to connect the transducer wires, you will see two srewed wire connections below the terminal blocks. On the installation instruction there is a black wire crimped to one of them. Where is that black wire going. ?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by Troubleshooter101 on December 19th, 2016 10:22 PM

This answer was accepted by the poster of the original question.

Troubleshooter101

Member since:
September 30th, 2015

Points: 2,927,030

1,100
points

Check this link below it has all the installation instructions you need.

http://www.thehulltruth.com/marine-electronics-forum/776976-problem-wiring-garmin-gsd-26-sounder.html

Thanks

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Troublshooter101

Related Garmin GSD 26 Manual Pages

Installation Instructions - Page 1

... mounting surface, using the sounder as you from the GSD 24/26. Proper transducer selection and installation are not using the selected mounting hardware. GSD 24/26 Installation notice The GSD 24/26 must carefully plan the GSD 24/26 sounder installation. 1 Select a mounting location (page 1). 2 Mount the sounder (page 1). 3 Connect the sounder to the Garmin Marine Network and to power (page...

Installation Instructions - Page 2

... of the cables. Preparing the Cable 1 Remove the terminal block lid from the sounder with a #2 Phillips screwdriver. When routing cables through one of the large cord grips ➋ on the housing, and pull it into place. 5 After the cable is located on your chartplotter. Refer to the GSD 24 Transducer Adaptor Installation Instructions included in . (32 mm) paddle...

Installation Instructions - Page 3

... Temperature and XID Note: The temperature and XID wires can be connected at either location. Transducer Wiring Diagrams You can use these diagrams to identify the connection points for your transducer model in the wiring color tables on the GSD 26 terminal block. If you are connecting two single-element transducers, connect the second transducer to one of the connector. SHIELD LOW FREQ...

Installation Instructions - Page 4

... Garmin 50/200 Airmar B117 depth only + - Outer Shield Black Bare Black Bare Black Bare Black Bare Black Bare Black Bare Black Bare Black Bare Black Bare Black Bare NA Bare Black Bare Black Bare Blue Bare Black Bare 4 GSD 24/26 Installation Instructions XID must be connected to help identify wire functions on the same side. ** Yellow before 11/2010 High...

Installation Instructions - Page 5

... Red Red/Green Red Red Blink Speed Slow Slow Fast Very Fast Solid Status Sounder is connected to a chartplotter and is connected to the chartplotter and this product. FCC Compliance This device complies with Industry Canada Standard RSS-210. GSD 24/26 Installation Instructions 5 Sounder is required as to the accuracy or completeness of the original sales receipt...

Installation Instructions - Page 6

...Australian Purchases: Our goods come with guarantees that cannot be excluded under Garmin's Marine Warranty Policy. © 2011 Garmin Ltd. You are trademarks of this ...warranty period and additional terms and conditions. Dynacolor™, GMS™, and GSD™ are also entitled to change or improve its subsidiaries, registered in the...covered under the Australian Consumer Law.