Frigidaire GLEQ2152ES Support Question
Frigidaire GLEQ2152ES Support Question
Find answers below for this question about Frigidaire GLEQ2152ES - Electric Dryer.Need a Frigidaire GLEQ2152ES manual? We have 4 online manuals for this item!
Question posted by trevorcoleneuman on May 2nd, 2013
Error Code E56
dryer will run for a few minutes then the timer will go away while it is still running and it wont heat up
Current Answers
Answer #1: Posted by OnlineOutreachSpecialist on May 3rd, 2013 7:31 AM
OnlineOutreachSpecialist
Member since:
March 30th, 2011 Points: 2,848,320
Member since:
March 30th, 2011 Points: 2,848,320
Good Morning trevorcoleneuman – Are you certain the error code is E56? Could it possibly be an E5B? If so, E5B typically indicates a heater fault issue. The dryer temperature reading of the control thermistor is not changing in a set amount of time. Try resetting the unit by either unplugging it or flipping the household circuit breaker to the off position. Wait roughly ten minutes and turn on the dryer. Select a normal cycle and verify if the dryer continues to display the error code. If resetting the power does not correct the issue, then I personally suggest contacting a professional to accurately proceed further.
Online Outreach Specialist
Related Frigidaire GLEQ2152ES Manual Pages
Use and Care Manual - Page 2
... potential negative consequences for the recycling of electrical and electronic equipment. You can happen if the instructions are found on the dryer • Operation
serial plate located of the...Number This Use and Care Guide provides general operating
instructions for ease of use any electrical switch; Always read and obey all instructions before using this manual must be preceded by...
Use and Care Manual - Page 3
...laundry or throw rugs against the front or back of the dryer. • Do not spray any type of children's reach. Children might use an adaptor plug or extension cord or remove grounding prong from electrical... materials, when heated, can occur. Fire hazard, overheating and damage to follow these Important Safety Instructions: • To reduce the risk of fire, electrical shock, or injury...
Use and Care Manual - Page 4
...Dryer heat may not have it inside . • Close the door and press Start to persons, read and follow fabric care labels and laundry product labels. Fill out the load with local codes. See Operating Instructions for drying. • Dry items of static electricity...Do not use any service or cleaning.
If the dryer is running open the door. A service technician must be exposed...
Use and Care Manual - Page 5
... not in warm, soapy water. Refer to avoid electrical shock hazards.
• Do not use any type spray cleanser when cleaning dryer interior. Leave space between items, but do not let items hang over time. Use only the Air Fluff/No Heat option for directions on the lint screen from noncolorfast fabrics, clean...
Use and Care Manual - Page 6
...8226; Leaving items in washer or dryer to
electricity.
• Or, add a fabric softener sheet and
reduce static electricity.
• Lint screen not clean
tumble without heat.
• Remove items when they...
6 Care and Cleaning con't
Do not store or place laundry products on top of dryer at medium or low heat for 5-10 minutes.
• Remove items immediately. Outside
• Clean the...
Use and Care Manual - Page 7
...be clogged or restricted. House fuse blown or circuit breaker tripped. Dryer runs but the heater will be at least 4 inches in INSTALLATION INSTRUCTIONS....Dryer should heat when utility service is not open . Lint screen is empty or there has been a utility interruption of the dryer feels too hot or smells hot.
High humidity. When in or plug may be loose.
POSSIBLE CAUSE
Electrical...
Technical Data Sheet - Page 1
... the first digit of the code and the START indicator light will pause for anything that cycle. The code is obtained by internal Watchdog timer. Example E24: The five ...ERROR CODES 1. Rotate the cycle selector knob to HIGH HEAT and touch START. The five indicator lights and the START indicator light start dryer. Problem with solid doors or door seal not correctly seated.
Clear code...
Technical Data Sheet - Page 2
...a digit display, the More Dry LED should be reset for six seconds or disconnect power from dryer. When the START key is pressed, all the cycle status LED's should be rotated to 12... key is pressed, all the cycle status LED's should light. heat source is pressed, all LED'S will flash. 1 O'clock: Drive motor runs; Drying LED is lit. Immediately after, press and hold the Select...
Installation Instructions - Page 2
...connectors with upturned ends or closed loop connectors and marked for use with clothes dryers.
See ELECTRICAL CONNECTIONS for Installation: 1. Rigid or flexible metal 4 inch (10.2 cm... 240 volt, single phase, 60 Hz, Alternating Current. ELECTRICAL REQUIREMENTS
ELECTRIC Dryer
CIRCUIT - POWER SUPPLY CORD KIT -
Duct tape. 6. The dryer is in your building. · Clear the room,...
Installation Instructions - Page 3
...in death, explosion, fire or burns. The following method must be exhausted into the laundry area.
Do not screen the exhaust ends of air. If the manometer reading is ...(30.5 cm) clearance between the
dryer and the point the exhaust connects to do so can result in operation.
Set the dryer timer and temperature to exhaust the dryer. To avoid restricting the outlet, maintain...
Installation Instructions - Page 4
...recess or
closet, MUST be solid with the National Fuel Gas Code, ANSI Z223.1 (latest edition).
4 Stainless steel or plastic-...electric dryers, exhausting can be installed immediately upstream of the gas supply connection to down drafts causing an increase in vent restriction. • Running the exhaust system through a roof may expose the exhaust
system to the dryer.
6. The dryer...
Installation Instructions - Page 5
inches (387.1 sq. inches (387.1 sq. cm)
CLOSET DOOR
0" (0 cm)
15" (38.1 cm)
1" (2.54 cm) 0" (0 cm)
5 This dryer MUST be exhausted outdoors.
5. The following illustrations show minimum clearance dimensions for sides, rear, and top. NOTE: Under counter and stack models - 0 inches (0 cm) for ...
Installation Instructions - Page 6
... (70.49cm) 28.5 to clear door handle (72.39cm)
2.375" (6.03cm)
(34.29cm) 13.5" To rear & base exhausts
27.0"
(68.58cm)
Stacked Dryer Installation Dimensions
(68.58cm) 27.0"
Electrical supply on rear of unit
28.25" to front of cabinet(71.76cm)
28.75" to clear knobs (73.03cm) 29.5" to clear...
Installation Instructions - Page 7
...Installation MUST conform to scratch the paint.
2.
"Solid door " Reversal Instructions:
1. Open the dryer door. Be careful not to current Manufactured Home Construction & Safety Standard (which is a Federal ...firmly before removing the last two screws.
3. UNPACKING
1. PACKING
REVERSING DOOR SWING
Your dryer is to the mobile home structure.
3. Install the four hinge hole plugs in ...
Installation Instructions - Page 8
...Install the door assembly on the left side of the door opening .
Be careful to the dryer front panel. Lay the door on the lens with the handle holes in Step 2. Note ...
Steps 4 & 5
Step 7 Retain the plugs for use later. Be careful to help remove the plugs. Open the dryer door. NOTE:
You may need a plastic knife to keep it 180°. Align the handle holes in Step 4. 9....
Installation Instructions - Page 9
...your protection against shock hazard and should be purchased, allowing some slack in this dryer. or an equipment grounding conductor must be properly grounded. Refer to be plugged directly... grounding conductor can melt, creating electrical shock and/or fire hazard. If the strain relief is equipped with all local codes and ordinances. GAS Dryer
This dryer is a copper wired power cord...
Installation Instructions - Page 10
...
NEUTRAL GROUND WIRE
RED
BLACK TIGHTEN
NUT
WHITE
TO THESE THREADS
NUT
STRAIN RELIEF MOUNTING BRACKET
STRAIN RELIEF MOUNTING B R A C K E T POWER CORD
POWER CORD
ELECTRICAL CONNECTIONS FOR 4-WIRE SYSTEM
ELECTRIC Dryer
ELECTRICAL CONNECTIONS FOR 3-WIRE SYSTEM
ELECTRIC Dryer
1. Attach the power cord neutral (center wire) conductor to the silver-colored center terminal on the back of the...
Installation Instructions - Page 11
...controls.
Label all wires prior to seal all other flammable vapors. Wiring errors can become airtight chambers causing suffocation. Children might use them for proper operation. The ...dryer for a connection. Place these instructions in your dryer, call 1-800-944-9044, or visit our website, www.frigidaire.com, for gas leaks with this happens, turn the timer to "OFF" and wait 5 minutes...
Operating Instructions - Page 1
...fold.
9. Auto Dry Applies to handle during unloading. The dryer senses the moisture level of the cycle and periodically during a ...has reached the selected dryness level, it tumbles through heated air.
Delicate Select this Auto Dry cycle for ...just a few items. It provides approximately 20 minutes of ventillation system, electrical voltage or gas pressure can also affect drying time...
Operating Instructions - Page 3
...:
Estimated drying time *** Temperatures
High Medium-High
Medium Low
No Heat Dryness Level
Towels 60 minutes
*
**
Normal Perm Press Delicate Quick 50 minutes 40 minutes 20 minutes 30 minutes
*
*
*
*
**
**
**
Bulky 45 minutes
*
Timed Dry 15 to remove softener sheet residue Clean out ventilation system. Consult the Error Code Chart below or the "Avoid Service Checklist" in the control...
Similar Questions
Error Code Ef2
my dryer has given me the error code of ef2. Can you tell me what that means
my dryer has given me the error code of ef2. Can you tell me what that means
(Posted by Btoddsfamily 7 years ago)
Give Me A Diagran Of Where Is The Fuse Locatedin A Frigidaire Electric Dryer
(Posted by 101robi 9 years ago)
Accessing Error Codes
I have a Frigidaire Affinity model FAQE7001LW0 serial number 4D11408250 mfg date 04/11. The indicato...
I have a Frigidaire Affinity model FAQE7001LW0 serial number 4D11408250 mfg date 04/11. The indicato...
(Posted by llyerly 10 years ago)
Frigidaire Gleq2152es Electric Dryer Runs A While, Heats On Then Stops After 10m
(Posted by thespen691 13 years ago)