Frigidaire GLEQ2152ES Support Question
Frigidaire GLEQ2152ES Support Question
Find answers below for this question about Frigidaire GLEQ2152ES - Electric Dryer.Need a Frigidaire GLEQ2152ES manual? We have 4 online manuals for this item!
Question posted by carterchris575 on July 25th, 2015
Detergent Leaked On Control Panel
I took it all apart and wiped and blow dryer all of the detergent I could off... it is still coming on, but motor will not come on. The light is saying drying, but nothing.. help before my wife finds out
Current Answers
Related Frigidaire GLEQ2152ES Manual Pages
Use and Care Manual - Page 2
...help... Instructions...2-4 Drying Procedures...4 Features...5 Care and Cleaning...5-6 Common Drying Problems...6 Avoid...dryer may be followed to minimize the risk of fire or explosion or to reduce the chance of others .
This
Record Your Model and Serial Numbers
book contains valuable information about features for ease of use any electrical...you to light any appliance. •...
Use and Care Manual - Page 3
..., bedspreads or plastic sheets can become airtight chambers. • Keep laundry products out of aerosol into, on product labels. • Before the dryer is removed from electrical power cord. Note: The instructions appearing in inefficient drying and possible fire. You can occur. If your dryer. Some rubber materials, when heated, can cause serious injury, fire...
Use and Care Manual - Page 4
...Allow the drum to come to persons, read and follow fabric care labels and laundry product labels. Do ...light-colored items. Separate items that shed lint from the electrical supply before operating this Owner's
Guide. When the cycle ends, remove items immediately and hang or fold.
4 Failure to 1/2 full. Drying Procedures
Follow fabric care label instructions. Wait until the dryer...
Use and Care Manual - Page 5
...dryer interior, unplug the electrical power cord to be connected to the dryer. An excessive amount of lint build-up could occur. Do not tumble other items when using dryer-added fabric softener sheets. Select Timed Dry. Lint build-up . Dry... dryer interior. If lint screen is opened to dry items which causes longer drying times. Drying Rack (some models) A drum light will come on...
Use and Care Manual - Page 6
...dryer, place a strip of cardboard or thin fiberboard under the front leveling legs to prevent damage to complete drying. • Block knits into shape. They can damage the finish or controls...warm water and mild detergent. Shrinking
• ...laundry products on top of load
before starting the dryer...dryer to
electricity.
• Or, add a fabric softener sheet and
reduce static electricity...
Use and Care Manual - Page 7
... a scrap of the Foreign objects such as cycle ends. Electric dryer is clogged with lint. Dryer is restored.
The list includes common occurrences that are 2 house fuses in INSTALLATION INSTRUCTIONS.
Dryer should heat when utility service is overloaded. Drying procedures have not been met. Excessive wrinkling.
Drying temperature too high.
It may be necessary to a 208...
Technical Data Sheet - Page 1
... electronic control. If problem persists, replace electronic control. Clear code, exit mode and start dryer. Remove wires from dryer. CAUTION: DISCONNECT ELECTRICAL CURRENT ...control.
If button is free but code returns, replace electronic control. Dryer Tech Data Sheet
This information is intended for a number higher than nine. On good models, the five indicator lights of Drying...
Technical Data Sheet - Page 2
... Pause Cancel buttons simultaneously for six seconds. 3. heat source is pressed, all the cycle status LED's should light. Key test: a. e. Drying LED is lit. Dryer will flash. 1 O'clock: Drive motor runs; Position cycle selector to determine the control thermistor temperature reading. Immediately after, press and hold Pause Cancel and START buttons simultaneously for regular...
Installation Instructions - Page 2
...so the power supply cord is accessible when the dryer is equipped with a 15 amp. POWER SUPPLY CORD KIT -
Carpenter's level. 4. ELECTRICAL REQUIREMENTS
ELECTRIC Dryer
CIRCUIT - Individual 30 amp. POWER SUPPLY -... in the installed position. See ELECTRICAL CONNECTIONS for Installation: 1. NEMA 10-30R (3-wire) receptacle or NEMA 14-30R (4-wire) receptacle to light any appliance. · Do ...
Installation Instructions - Page 3
... to do so can create excessive drying times and fire hazards. Failure to the outside of insects and rodents. The dryer exhaust system MUST be exhausted into the laundry area.
Flexible Metal Duct
VENT HOOD...or metal foil duct, replace it must be used to come in the charts, the following are kept or stored. If the dryer is unacceptable.
3 EXHAUST SYSTEM REQUIREMENTS
Use only 4 inch...
Installation Instructions - Page 4
However, on electric dryers, exhausting can be to dripping water or outside weather
conditions. 2. Follow the instructions supplied with a maximum slope of 1 inch (2.54 cm). If codes allow, flexible metal tubing may be used , the more the dryer is used to connect your dryer to the gas supply line. The tubing MUST be used.
2. In...
Installation Instructions - Page 6
... (70.49cm) 28.5 to clear door handle (72.39cm)
2.375" (6.03cm)
(34.29cm) 13.5" To rear & base exhausts
27.0"
(68.58cm)
Stacked Dryer Installation Dimensions
(68.58cm) 27.0"
Electrical supply on rear of unit
28.25" to front of cabinet(71.76cm)
28.75" to clear knobs (73.03cm) 29.5" to clear...
Installation Instructions - Page 7
...control panel as a means to current Manufactured Home Construction & Safety Standard (which is a Federal Regulation Title 24 CFR-Part 32-80) or when such standard is designed so the door swing may need a plastic knife to the opposite side of the cabinet. FOAM SHIPPING PAD
The dryer...Kit No. 346764 is accomplished by transferring hinges to help pull out the plugs. Refer to the floor. ...
Installation Instructions - Page 8
... to reinstall the hinges. 11. Be careful to the dryer front panel. Remove the two hinges and reinstall the four screws. Open the dryer door. Retain the plugs for use later. Remove the ...it from each hinge first. Note the installation orientation of the door to help remove the plugs. Be careful to help remove the plugs. Install the plugs from Step 1 into the holes left...
Installation Instructions - Page 9
..., grounding will have longer drying times than operating on the appliance. This appliance MUST be grounded. For a permanently connected dryer: 1. A U.L. NOTE: Dryers operating on 208 volt power supply will reduce the risk of electrical shock by any movement of the cord, resulting in a risk of electrical shock. ELECTRICAL INSTALLATION
ELECTRIC Dryer
The following are specific requirements...
Installation Instructions - Page 10
...BLACK TIGHTEN
NUT
WHITE
TO THESE THREADS
NUT
STRAIN RELIEF MOUNTING BRACKET
STRAIN RELIEF MOUNTING B R A C K E T POWER CORD
POWER CORD
ELECTRICAL CONNECTIONS FOR 4-WIRE SYSTEM
ELECTRIC Dryer
ELECTRICAL CONNECTIONS FOR 3-WIRE SYSTEM
ELECTRIC Dryer
1. TYPICAL 4 CONDUCTOR
BLACK 240V WHITE NEUTRAL
3. Thread a U.L. TYPICAL 4 CONDUCTOR
RED 240V GREEN GROUND
4. Do not make a sharp bend...
Installation Instructions - Page 11
... switch will light, it is off . If the burner does not light within 45 seconds the first time the dryer is located inside the dryer console or under the top panel. NOTE: ...into the outlet.
4.
REPLACEMENT PARTS
If replacements parts are not meant to disconnection when servicing controls. Label all connections by a qualified gas technician.
2. Destroy the carton and plastic bags after...
Operating Instructions - Page 1
...helps reduce wrinkling and makes items easier to persons, read the IMPORTANT SAFETY INSTRUCTIONS in place.
3.
Drying time varies depending on items to delete an option.
Normal Select this Auto Dry... a dryer fabric softener sheet. A suitable drying temperature, dryness level and options will not light.
6....ventillation system, electrical voltage or gas pressure can also affect drying time. It...
Operating Instructions - Page 2
... wrinkle free, permanent press and lightweight fabrics.
Note: To prevent over-drying, not every dryness level is selected.
Dryer Features
Control To avoid having someone accidentally start or stop the dryer, press OPTIONS and SELECT at the end of the cycle. Status Lights The following indicators may be changed before hanging or ironing. Cycle Selection...
Operating Instructions - Page 3
... are available with the following cycles:
Estimated drying time *** Temperatures
High Medium-High
Medium Low...lightly and release. Press PAUSE/CANCEL twice.
ERROR CODE CHART
If the dryer stops, the status lights flash, the signal beeps and a code is based on normal
dryness level and factory settings. Consult the Error Code Chart below or the "Avoid Service Checklist" in the control panel...
Similar Questions
No Power To Control Panel.
I opened the door to check how dry my load was and now the dryer has no power to control panel.
I opened the door to check how dry my load was and now the dryer has no power to control panel.
(Posted by sfstrong1 6 years ago)
My Dryer Leq2152ee1 Will Not Start Lightnig Storm May Have Fried Control Panel
dryer 11
dryer 11
(Posted by fhdavisjr 7 years ago)
Give Me A Diagran Of Where Is The Fuse Locatedin A Frigidaire Electric Dryer
(Posted by 101robi 9 years ago)
How To Replace Belt For Gleq2152es0 Frigidaire Electric Dryer
(Posted by HBChodian 10 years ago)
Frigidaire Gleq2152es Electric Dryer Runs A While, Heats On Then Stops After 10m
(Posted by thespen691 13 years ago)