Frigidaire FTF530FS Support Question
Frigidaire FTF530FS Support Question
Find answers below for this question about Frigidaire FTF530FS - 27" Front-Load Washer.Need a Frigidaire FTF530FS manual? We have 3 online manuals for this item!
Question posted by delDenni on February 1st, 2014
Frigidaire Ftf530fs1 Dryer Wont Start
The person who posted this question about this Frigidaire product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by OnlineOutreachSpecialist on February 25th, 2014 7:12 AM
OnlineOutreachSpecialist
Member since:
March 30th, 2011 Points: 2,848,320
Member since:
March 30th, 2011 Points: 2,848,320
Hi delDenni! I see on your post you are having a difficult time with a dryer not starting but you have attached your question to a Frigidaire frontload washer (model # FTF530FS). In both cases, there are common things to check before contacting a service provider. First, Make sure that the door is latching completely; there could be an issue with the door strike. Check to make sure that the knob is set to the desired setting. Next, ensure the plug is secure; sometimes an off-balanced load can unplug the washer. Check the house fuse or circuit breaker to ensure it has not blown or tripped without notice. Make sure the electrical outlet is not overloaded; the dryer should be the only item on its circuit. Last, double-check the water supply to confirm it is on. If all of these suggestions pan out and the problem still persists, think about what may have happened prior to this occurrence. For instance, did you notice any error codes, odors, or other strange functions prior to this issue? If you are still having these issues and can think of anything in particular, please feel free to reconnect. Hope this helps!
~Best Regards~
Online Outreach Specialist
Related Frigidaire FTF530FS Manual Pages
Wiring Diagram (All Languages) - Page 1
...repair a major appliance may cause tub rotation to the washer. IMPORTANT
If grounding wires, screws or clips used to complete a path to the start -up.
• Extremely low water pressure may ...background of the speed control unit. Remove the 6 pin plug from Electrical Supply Before Servicing Washer.
If good, and motor does not run go to the Heavy Wash position of electric shock...
Wiring Diagram (All Languages) - Page 2
... complete a path to their original position and properly fastened.
DIAGNOSTIC STRIP CIRCUITS
PART NO. 134968300 A MOTOR
12T TIMER
14C TIMER
* TIMER CONTACTS SHOWN
AT THE START OF THE REGULAR WASH CYCLE.
* 1C
* 3C * 5C * 7C
1B TIMER
3B TIMER
5B TIMER
7B TIMER
C10.4 (T1) C6.4 (GND)
C10.2 (A)
C10.1 (B)
C10.6 (C)
C10...
Wiring Diagram (All Languages) - Page 5
NO LOAD, START POSITION OF PERMANENT PRESS
WHITE SIDE
1 I 11231241
3 I I PI I
5
I H 1118 1
7
N I
1115 1
9
I e ll I
11
I Fi l l
13
15 TC B D
BLACK SIDE
I I 1 2 11 0
I ISO I
2
ILiM~9 4• 17 4
I - 4,1110 6
1 115 ...
Installation Instructions (All Languages) - Page 1
... est impossible de joindre la compagnie de gaz, appeler les pompiers.
Installation Instructions
Full Size Tumble Action Washers
Notice d'installation
Machine à laver par culbutage
Before beginning installation, carefully read these instructions near the washer after installation for future reference. REMARQUE: L'alimentation électrique de la laveuse doit respecter les codes et...
Installation Instructions (All Languages) - Page 2
...60
OUTLET RECEPTACLE - per foot (1.27 cm per square inch (maximum unbalance pressure, hot vs. Check with the National Electrical Codes, ANSI/NFPA 70 (latest edition). CONTENTS
SUBJECT
PAGE
Pre-Installation Requirements 2
Electrical Requirement 2
Grounding Requirement 2
Water Supply Requirements 2
Drain Requirements 2
Location Of Your Washer 2
Unpacking 2-3
Rough-In Dimensions...
Installation Instructions (All Languages) - Page 3
... and the base. Kit is required.
3 Remove the following from an authorized parts distributor. *Custom sized countertop is available from the back side of the washer until free, then pull it out.
10. Remove the large styrofoam block located under counter* installation is to be transported at a later date, the shipping...
Installation Instructions (All Languages) - Page 4
...Frigidaire Company Authorized Parts Distributor nearest you time and money. 9. Turn on and check for play. They contain valuable and helpful information that may occur. Place these connections.
4. INSTALLATION
Leveling the Washer... tightly by properly leveling the washer.
1. Place in a laundry tub or standpipe and secure with the washer in this washer are needed for future reference...
Operating Instructions (Operating Instructions) - Page 1
... time you may see water in your washer Use and Care Guide. Add laundry load to restart the washer.
9. Sort laundry into loads that can be completely closed , the Door Lock Indicator lights up when the washer starts, and turns off at the end of each load.
7. Push in U. A.
8. P/N 134576700 (0506) Start the washer by closing the door and pulling out...
Operating Instructions (Operating Instructions) - Page 2
... provides up when the cycle selector knob is no need to select a water level because the washer automatically adjusts the water level to LOUD. This determines water temperatures for basic fabric types. Note... effective at the end of the cycle. The Cycle Signal is turned to 17 minutes of wash load.
P/N 134576700 (0506)
A signal will not sound at the end of the cycle.
Regular Cycle...
Similar Questions
Wont Start Wash Cycle?
when start wash cycle, machine will spin drum back n forth but will not fill with water, then as tim...
when start wash cycle, machine will spin drum back n forth but will not fill with water, then as tim...
(Posted by Jeffgoode1 2 years ago)
Front Load Dryer Wont Spin
(Posted by dmycolbe 9 years ago)
Frigidaire Ftf530fs Wont Start
(Posted by Airmakher 10 years ago)
Washer Dryer Combo, Washer Won't Agitate, Dryer Wont Heat Up
(Posted by sakparr25 10 years ago)
Frigidaire Affinity Wont Start,
error code e91 replaced user interface,control board still wont start. does beep but no lights. will...
error code e91 replaced user interface,control board still wont start. does beep but no lights. will...
(Posted by bullyboyzz 11 years ago)