Frigidaire FEQ1442ES Support Question
Frigidaire FEQ1442ES Support Question
Find answers below for this question about Frigidaire FEQ1442ES - 27" Electric Dryer.Need a Frigidaire FEQ1442ES manual? We have 2 online manuals for this item!
Question posted by reman on September 10th, 2014
How To Find Thermal Fuse In Fridgedaire Dryer Number Feq1442es0
The person who posted this question about this Frigidaire product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Frigidaire FEQ1442ES Manual Pages
Installation Instructions - Page 2
... your gas supplier from
plug. ELECTRICAL REQUIREMENTS
ELECTRIC Dryer
CIRCUIT - POWER SUPPLY - 3 wire or 4-wire, 240 volt, single phase, 60 Hz, Alternating Current. See ELECTRICAL CONNECTIONS for Installation: 1. NEMA 10... laundry area.
All male duct pipe fittings MUST be performed by a qualified installer,
service agency or the gas supplier. POWER SUPPLY CORD - Number of your dryer....
Installation Instructions - Page 3
... (0 cm) 15" (38.1 cm)
60 sq. INSTALLATION IN RECESS OR CLOSET
1. Your dryer needs the space around it will obstruct the flow of 1/2 inch (1.27 cm) pipe. 3. The system back pressure MUST NOT be higher than
1/2 psig (3.45 kPa..., drapes, or
anything that is not plasticcoated. Read the measurement on electric dryers, exhausting can be to the right or left side of the cabinet or the...
Installation Instructions - Page 4
... to clear knobs (70.49cm) 28.5 to clear door handle (72.39cm)
2.375" (6.03cm)
(34.29cm) 13.5" To rear & base exhausts
27.0"
(68.58cm)
Stacked Dryer Installation Dimensions
(68.58cm) 27.0"
Electrical supply on rear of unit
28.25" to front of cabinet(71.76cm)
28.75" to clear knobs (73.03cm) 29.5" to...
Installation Instructions - Page 5
...mobile home structure.
3. REMOVE 4 SCREWS (ONE FROM EACH HINGE FIRST)
5 When installing a gas dryer into a mobile home, a provision must be reversed at any time without additional parts. Refer to pick...accomplished by transferring hinges to be made for Mobile Homes. Be careful not to the dryer front panel (see below).
Remove the four screws that will not support combustion. ...
Installation Instructions - Page 6
... handle screws and remove the handle by removing the door in the transition ring. 8. Align the handle holes in Step 4. 7. Open the dryer door. Be careful to the dryer front panel. Remove the screws from turning. Remove the four hinge hole plugs from the left by removing the handle screws in the...
Installation Instructions - Page 7
... and/or fire hazard. In the event of least resistance for proper grounding.
Some extension cords are in this time.
3.
For a grounded, cord-connected dryer: 1. ELECTRIC Dryer
TYPICAL 4 CONDUCTOR
TYPICAL 4 CONDUCTOR
BLACK WHITE
1. Reattach the strain relief mounting bracket to be cut or remove the grounding prong from the green ground screw ...
Installation Instructions - Page 8
...supply line to children.
Use duct tape to L.P. The dryer MUST be level and resting solid on the power at circuit breaker/fuse box before calling for gas leaks with rugs, bedspreads,...of liquefied gases on all joints. Connect a 1/2 inch (1.27 cm) I.D. If the burner does not light within 45 seconds the first time the dryer is resting solid on all four legs.
3. Pedestal A ...
Operating Instructions - Page 1
... place.
3. Cycle Selection
For best results, follow the fabric care label instructions on size and dampness of fire, electric shock or injury to dry cottons and blends with a no-iron finish. The dryer senses the moisture level of the cycle and periodically during Press Saver when the Cycle Signal option is made...
Operating Instructions - Page 2
...-drying, not every dryness level is started.
The Cycle Signal will not be able to a numbered setting. The load may be removed any load, turn the knob to select a cycle or ...not use heat to help reduce wrinkling. If a dryness level or option is selected. See the "Dryer Settings Chart" for wrinkle free, permanent press and lightweight fabrics. If changes are available in the ...
Operating Instructions - Page 3
...release.
Ventilation system clogged. Reduce load size. Disengage button. Dryer overloaded.
DRYER SETTINGS CHART
These temperatures, dryness levels and options are available... Estimated cycle duration is based on normal
dryness level and factory settings. ERROR CODE CHART
If the dryer stops, the status lights flash and the signal beeps, an error has occured. Make correction, then...
Similar Questions
Frigidaire Dryer Beeps Three Times And Wont Start
(Posted by smewaltja 9 years ago)
How To Change Fuse Frigidaire Dryer Gleq2152es1
(Posted by eeto 10 years ago)
Fridgidaire Electric Dryer Model Fase703lwo Not Starting
Our dryer is not starting and reads door open. An error code did appear however disappeard and has n...
Our dryer is not starting and reads door open. An error code did appear however disappeard and has n...
(Posted by juliemccleskey 11 years ago)
Frigidaire Dryer Feq1442es0 Won't Start. 3 Beeps 3 Light Flashes At Same Time.
Frigidaire Dryer FEQ1442ES0 will not start. Gives 3 beeps with indicater lights flashing at the same...
Frigidaire Dryer FEQ1442ES0 will not start. Gives 3 beeps with indicater lights flashing at the same...
(Posted by Spicer 11 years ago)
Dryer
My dryer will not heat up. I have brought the heating element in and had it tested and it was good s...
My dryer will not heat up. I have brought the heating element in and had it tested and it was good s...
(Posted by Briana07Serrato 13 years ago)