Dewalt DW745 Support Question
Dewalt DW745 Support Question
Find answers below for this question about Dewalt DW745.Need a Dewalt DW745 manual? We have 1 online manual for this item!
Question posted by sjsbsmitty on August 18th, 2014
Having Problems With The Anti-kickback Sticking On The Throat Plate When Raisin
and lowering the saw blade.
Current Answers
Related Dewalt DW745 Manual Pages
Instruction Manual - Page 3
...reverse the plug.
Double Insulation
If saw is not permitted by the Canadian Electric Code. Tools built with this equipment has a....
Important Safety Instructions
• TO REDUCE THE RISK OF KICKBACK AND OTHER INJURIES, KEEP GUARDS IN PLACE and in Fig...if not avoided, will fit in a polarized outlet only one blade is used only until a properly grounded outlet can be grounded...
Instruction Manual - Page 4
... FREEHAND. • NEVER reach around or over saw is unintentionally contacted.
• CHECK FOR DAMAGED PARTS. A push stick is a wooden or non-metallic stick, usually homemade, that is damaged should be sure...to place your model. Also use of your saw -blade guard and splitter for every operation for your hands within six inches of the tool, a guard or other part that should ...
Instruction Manual - Page 5
... that the rip fence is used . Keep saw blade guard, splitter and anti-kickback teeth in loss of a push stick. The splitter must be in alignment with any...THROAT PLATE MUST BE IN PLACE AT ALL TIMES to prevent unauthorized use a special fixture. NEVER rip a work piece) unsupported so the spring of the board causes it to a wooden stick, usually homemade, that is equipped with a blade...
Instruction Manual - Page 6
... approved respiratory protection appropriate for proper dust removal. SAVE THESE INSTRUCTIONS FOR FUTURE USE
Specifications
15 AMP Miter Angle Bevel Angle Blade Size Max. Blade guard 4. Carefully unpack the table saw out, as those dust masks that parts have not
FIGURE 3 A. Blade D. Fence rails G. Rip fence rear latch S. Adjustable feet N. Handle Q. Anti-kickback teeth
V.
Instruction Manual - Page 7
... THE BLADE
1. If replacing the blade, remove the blade guard (D) and throat plate (X) prior to installing the new blade. (Refer to move it, change the blade with the opening (BB). 2.
Remove the throat plate (X) by snapping the latches onto the rails as necessary until the nut and washer are free of dust and
debris before installing.
6. ASSEMBLE YOUR SAW IN...
Instruction Manual - Page 8
... FOR ALL POSSIBLE CUTS. Check alignment after each change of throat plate drops into place. Replace the throat plate. However, the wing nut must be in the handle of the blade. To attach the push stick to the saw blade arbor to the power source or operating the saw, always inspect the guard and splitter for proper alignment and...
Instruction Manual - Page 9
...service center at extra cost.
Connecting Saw to Power Source
WARNING: To reduce the risk of the plywood to anchor the table saw . All DEWALT tools are provided in the switch for... bevel crosscutting instructions before connecting saw table.
CAUTION: To reduce the risk of personal injury, make sure the switch is a concern, the DW745 can be clamped onto the ...thin kerf blades.
Instruction Manual - Page 10
...:
1. Take a little time now to follow the steps
below to adjust your saw is still loose, tighten the
spring further. LL
4. Unlock the rail lock lever (W).
2. FIG. 19 W
BLADE ALIGNMENT ADJUSTMENT
(Blade Parallel to make sure blade does not
hit the throat plate, causing personal injury. Locate the black Allen locator screws
(OO) that those elements...
Instruction Manual - Page 11
... until the source has been located and the problem corrected.
NOTE: This saw is intended for ripping operations to reduce the risk of a thrown work piece can also drag the operator's hand back into the blade if the operator's hand is through the splitter and has engaged anti-kickback teeth.
2. It is recommended that the...
Instruction Manual - Page 12
... connecting the table saw , located on
the right-side panel. Check alignment after each change of bevel angle. It is not safe
to put between the fence and the blade.
1.
WARNING: NEVER use a length stop , raise the anti-kickback teeth on and allow the blade to make push sticks.
FIG. 27
2. Adjust the blade height so that...
Instruction Manual - Page 13
...Operation
To set -ups or when making repairs. FIG. 30
Dust Collection
Your table saw . Unplug the saw blade causing damage to
the guard and personal injury. Clean out the excess dust, and ...apply to normal wear or tool abuse. This warranty does not cover part failure due to accessories or damage caused where repairs have difficulty raising or lowering the blade, contact a DEWALT authorized
...
Instruction Manual - Page 44
...-shaped humps on the surface of pyramids on the handgrip; DEWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD 21286 (JAN07) Form No. 650150-00 DW745 Copyright © 2006, 2007 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the kit box configuration; the...
Similar Questions
Blade Spins Loose
Hi, The abrasive blade seems to spin loose when started up and that causes blade to wobble lose, I h...
Hi, The abrasive blade seems to spin loose when started up and that causes blade to wobble lose, I h...
(Posted by ton31684 2 years ago)
Dewalt Dcb101 Problem Pack Or Charger
My newest DCB101 charger isn't working anymore. I have two other for a total of three. Just tonight ...
My newest DCB101 charger isn't working anymore. I have two other for a total of three. Just tonight ...
(Posted by justinkristensen 8 years ago)
Dad Throat Plate
I would like to buy a dado throat plate for my saw can you give me a part number
I would like to buy a dado throat plate for my saw can you give me a part number
(Posted by kenhenshaw 10 years ago)
Dct410 Battery Or Charger Problem
Hello, I own a DCT410 inspection camera and either the battery (DCB120) or the charger (DCB100) is n...
Hello, I own a DCT410 inspection camera and either the battery (DCB120) or the charger (DCB100) is n...
(Posted by bryanbrodeur 10 years ago)