Dewalt D28710 Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt D28710 manuals!
Problems with Dewalt D28710?
Ask a Question
Free Dewalt D28710 manuals!
Problems with Dewalt D28710?
Ask a Question
Most Recent Dewalt D28710 Questions
Blade Spins Loose
Hi, The abrasive blade seems to spin loose when started up and that causes blade to wobble lose, I h...
Hi, The abrasive blade seems to spin loose when started up and that causes blade to wobble lose, I h...
(Posted by ton31684 2 years ago)
Dewalt D28710 Videos
DeWalt D28710 355 mm CHOP SAW 2200 w
Duration: 1:48
Total Views: 32
Duration: 1:48
Total Views: 32
DEWALT D28710 14-Inch Abrasive Chop Saw
Duration: 1:26
Total Views: 153
Duration: 1:26
Total Views: 153
???????? ?? ????? DeWalt D28710 - 2200W
Duration: 2:39
Total Views: 2,490
Duration: 2:39
Total Views: 2,490
DeWALT D28710 - box opening
Duration: 4:35
Total Views: 696
Duration: 4:35
Total Views: 696
Popular Dewalt D28710 Manual Pages
Instruction Manual - Page 3
... operating product. Repair or replace damaged cords. Cluttered ... Safety Instructions
WARNING: Read all instructions listed ... Please read the manual and pay attention to...DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258).
CAUTION: WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS. An undersized cord will result in damp or wet locations, or expose them to install...
Instruction Manual - Page 4
... also be properly repaired or replaced.
• NEVER LEAVE TOOL RUNNING UNATTENDED. when changing accessories, such as blades, bits, cutters, and the like.
• REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is recommended. Before further use of power and overheating. TURN POWER OFF. Additional Safety Rules for Chop Saw
• Always wear...
Instruction Manual - Page 5
... brushes may ignite combustible materials.
• Do not use , noise from power sanding, sawing... abrasive wheel as a deburring grinder. WARNING: Some dust created by power sanding, sawing... Heavy-Duty 14" (355mm) Chop Saw:
FOR SAFE OPERATION READ THE INSTRUCTION MANUAL. CAUTION: ...CIRCULAR SAW BLADES OR ANY OTHER TOOTHED BLADES WITH THIS TOOL. WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS....
Instruction Manual - Page 8
...binding.
FIG. 4
QE
FORWARD
F
I H
WIDTH OF SPACER BLOCK
6
Material Clamping and Supporting
• Angles are best clamped and cut -off end should be level with deflector or ...the spark deflector (C) and then retighten screw. English
Standard Equipment
1 14" (355mm) metal cutting abrasive wheel 1 Wheel wrench 1 Instruction manual
To Carry (Fig. 1)
Fold down . Unlocking (Fig. 1)
To...
Instruction Manual - Page 9
... stop is set at the factory for a new 14" (355mm) wheel to remove clamping pressure.
Insert both fence bolts before making any adjustments or removing or installing attachments or .... Pull crank assembly out as far as spring, bar or C-clamps) will be pushed forward into supporting surface.
7
The fence (E) can be adjusted two ways: to change desired cutting angle and to...
Instruction Manual - Page 10
...CAUTION: Tool must be the thickness of the screws should be supported on
when replacing with the 8mm hex wrench (G).
L 8 Install the new abrasive wheel by hand until it has coasted to lock wheel. ... right-hand thread.
2.
Removal and Installation of the abrasive wheel with a new abrasive wheel. Do not make any adjustment while chop saw rests on stable, level, non-skid...
Instruction Manual - Page 11
... any adjustments or removing or installing attachments or accessories.
Place the chop saw at least once a week. Place boards tightly alongside and nail to do not overtighten).
FIG. 11
W
X
.2"
(6mm)
X
Brushes should be replaced. If replacing existing brush, maintain same orientation as shown in Figure 10 they should slide freely in these parts.
Use a cloth dampened only...
Instruction Manual - Page 12
...replacement.
10
If you are available at the factory to accessories or damage caused where repairs have other than those offered by DEWALT, have sufficient lubrication packed in Latin America.
This warranty does not cover part failure due to products sold in Latin America, see country specific... tested with this product, use of the chop saw. This warranty does not apply to last ...
Instruction Manual - Page 13
...2. Reduce number of tools
powered by authorized service center. 4. Glazed wheel. 2. Workpiece not clamped properly. See chart on page 2. 2. Have cord replaced by the generator. TOOL VIBRATES EXCESSIVELY DURING CUT
WHAT'S WRONG? 1. Damaged wheel. 3. BLADE DOES NOT COME UP TO SPEED
WHAT'S WRONG? 1. Tighten all mounting hardware. 2. TROUBLE! English
Troubleshooting Guide
TROUBLE!
Instruction Manual - Page 14
... flat against the base. Clamp workpiece securely. WHAT TO DO... 1. Check and adjust. See Material Clamping and
Supporting, page 6. MATERIAL MOVES DURING CUT WHAT'S WRONG? 1. Excessive force used to fence. 3. WHAT TO DO... 1. WHAT TO DO... 1. Vise too loose. 3. Push down slightly on page 7. 2. let the wheel do the work. 4. English
Troubleshooting Guide... TROUBLE!
Instruction Manual - Page 44
N096693
D28710
Copyright © 2011 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme, the "D" shaped air intake grill, the array of pyramids on
the handgrip, the kit box configuration, and the array of lozenge-shaped humps on the surface of the tool. DEWALT Industrial Tool...
Dewalt D28710 Reviews
We have not received any reviews for Dewalt yet.