Dell PowerConnect 6248 Support Question
Dell PowerConnect 6248 Support Question
Find answers below for this question about Dell PowerConnect 6248.Need a Dell PowerConnect 6248 manual? We have 5 online manuals for this item!
Question posted by kmabecyhens on July 31st, 2013
How To Save Configuration Settings On Dell Powerconnect 6248
The person who posted this question about this Dell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Dell PowerConnect 6248 Manual Pages
User's Guide - Page 19
....com. The topics covered in this product. 1
Introduction
This section describes the switch user-configurable features. The Dell PowerConnect 6224 switch supports 24 1000Base-T copper ports and 4 "combo" ports for RJ-45 or SFP interfaces.
The Dell PowerConnect 6248 supports 48 1000Base-T copper ports and 4 "combo" ports for RJ-45 or SFP interfaces. For a list of Service Features...
User's Guide - Page 74
...with Telnet, SSH, and so forth
74
Configuring Dell PowerConnect General Configuration Information
The PowerConnect 6200 Series switches are used to define the relationship of the switch to its unique network topology.
Other Configuration Requirements The following is required for downloading embedded software and configuring the switch: • ASCII terminal (or emulation) connected to...
User's Guide - Page 81
... in the basic initial configuration of a newly installed switch so that the initial administrator account be saved before rebooting. The wizard sets up . You may enter the system to make the switch manageable.
Configuring Dell PowerConnect
81 Configuration Overview
Before configuring the switch, obtain the following configuration on the switch:
• Establishes the initial...
User's Guide - Page 82
... you login until a configuration is disabled until you are allowed in the community string, their use is activated.
The next time the system reboots you return to run the set -up wizard. Although spaces are given another opportunity to configure security access for SNMPv3 (for the Easy Setup Wizard.
82
Configuring Dell PowerConnect Initially only SNMPv1...
User's Guide - Page 84
... manually configure the switch. Note: You can access the
SNMP, HTTP, and CLI interfaces. After you complete the wizard, the system is configured as follows: • SNMPv1/2c is enabled and the community string is set up as defined above.
If you like to run the setup wizard within 60 seconds)? [Y/N] y
Step 1:
84
Configuring Dell PowerConnect
Would...
User's Guide - Page 85
...can use Dell Network Manager or other accounts and change this account. For more information on setting up the initial SNMP version 2 account now.
You can :
o Set up an...********
Step 3:
Configuring Dell PowerConnect
85 o Return later and setup other SNMP accounts. (For more information on adding management systems, see the user documentation). To manage the switch using SNMP (...
User's Guide - Page 86
..., please select (Y) to save the configuration, and copy to the start-...switch. The IP address is the IP address you use to automatically request an IP address from the network DHCP server. 192.168.2.1 Please enter the IP subnet mask (A.B.C.D or /nn): 255.255.255.0 Step 4: Finally, set up configuration...Dell Easy Setup Wizard. console>
86
Configuring Dell PowerConnect To setup an IP address...
User's Guide - Page 88
... Telnet Password • Configuring an Initial HTTP Password • Configuring an Initial HTTPS Password
Modifying Switching Port Default Settings
When configuring/receiving IP addresses through DHCP and BOOTP, the configuration received from these servers includes the IP address, and may include subnet mask and default gateway.
88
Configuring Dell PowerConnect
There is used within...
User's Guide - Page 89
...• SwitchA# - SwitchA#configure
SwitchA(config)#exit
SwitchA#
The following table describes the switch port default settings. Port Default Settings
Function Port speed and mode ...blocking prevention Flow Control Back Pressure
Default Setting 1G Auto-negotiation Enabled On (Enabled) On Off
Configuring Dell PowerConnect
89 this by typing configure at the privileged EXEC mode.
•...
User's Guide - Page 91
... Dell PowerConnect
91 Data encryption is handled through the AAA (Authentication, Authorization, and Accounting) mechanism that manages user access rights, privileges, and management methods. The system is delivered with no default password configured; If a userdefined password is lost, a password recovery procedure can be set to enable access and configuration rights to the switch...
User's Guide - Page 94
... using XModem, which software version is currently running on the
switch.
94
Configuring Dell PowerConnect The following is an example of the information that the file...saved on the TFTP server (the .stk file). 3.
NOTE: You must be available on the network before downloading the software. Enter the command show version to verify which is a data transfer protocol for downloading switch...
User's Guide - Page 95
...image to start? (y/n) y
Configuring Dell PowerConnect
95
The following is an example of the information that appears:
console#copy tftp://10.254.24.64/pc62xxr0v34.stk image
Mode TFTP
Set TFTP Server IP 10.254....When the new image is downloaded, it is saved in the area allocated for the duration of the transfer Are you sure you want to the switch. The following is an example of the ...
User's Guide - Page 96
...Are you sure you want to continue? (y/n) 7. The following message displays:
console#reload
Management switch has unsaved changes. 5. Configuration Not Saved! Enter the command reload. The following message then displays.
console>show version to reboot the switch.
96
Configuring Dell PowerConnect Select the image for the next boot by entering the boot system command, the system...
User's Guide - Page 105
... for the purpose of switch when powered up - Using the RS-232 port, connect the switch to establish a remote network management connection with the following settings and select the appropriate COM port. ASCII terminal application (for example, Microsoft® Windows® HyperTerminal or Procomm
Plus™ Terminal) - Configuring Dell PowerConnect
105 Network adapter card -
User's Guide - Page 111
... %STP-I-PORTSTATUS: Port 1/xg1: STP status Forwarding
Configuring Dell PowerConnect
111
it is forwarding (after 30 seconds), as follows:
console>enable
console# 2. Ensure (on the serial console) that the interface status changed to "up" and that the STP status is set with the default settings. Are you sure you want to the switch, using a CAT5 Cable.
User's Guide - Page 112
...switch to the
interface, configure a static route.
Use the following command to set the IP address to DHCP and return to enter the Configuration mode as one of a remote network, and is a member of the switch...config)#username Dell password Dell1234 level 15
console(config)#ip http authentication local
console(config)#ip https authentication local
112
Configuring Dell PowerConnect a. ...
Release Notes - Page 4
...
PowerConnect 6224 PowerConnect 6248 PowerConnect 6224F PowerConnect 6224P PowerConnect 6248P
2
System Firmware Version 3.2.0.6
NOTE: OMNM 4.1 will not discover the switches running firmware version 2.x or earlier.
Firmware Downgrade
Downgrading from 3.2.0.6 to a previous release is currently running any version of 3.x.y.z firmware therefore users should save their configuration...
Release Notes - Page 19
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
Issues Resolved
The following is a list of updated time with timezone offset. WFB: Logging messages show running -config.
Missing RFC1213 MIB-2 SNMP Trap counter. Configured...
Set the unitMgrCfgFile -> dataChanged flag in the current firmware release. Process SET_ASSET_TAG event while in the web page.
Firmware missing no switch ...
Release Notes - Page 25
...modules as Ethernet ports.
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
RADIUS Accounting Servers
Title radius-server host acct
Description The switches do not support creating ...The switch remains in Interface Config Mode to set the number of the command to the Dell™ PowerConnect™ 6200 Series Systems CLI Reference Guide for 90 seconds.
Configurable Message...
Release Notes - Page 27
... other sessions.
If the configuration is saved and the switch is reset, the configuration is Read/Write capable.
TFTP gives no configuration changes have been made.
Once the timeout occurs, then the MOTD acknowledgement ends the connection and resumes processing of their configuration files. The user will not be able to save configuration changes even though no reason...
Similar Questions
How To Save Configuration Dell Powerconnect 2824
(Posted by smTomM 10 years ago)
How To Save Configuration On Dell Powerconnect 6248 Switch
(Posted by vgjayzi 10 years ago)
How To Set Powerconnect 6248 To Factory Default From Console Connection
(Posted by larrysm 10 years ago)
