Home » Cub Cadet » Lawn & Garden » Cub Cadet 2X 524 SWE

Cub Cadet 2X 524 SWE Support Question

Find answers below for this question about Cub Cadet 2X 524 SWE.
Need a Cub Cadet 2X 524 SWE manual? We have 2 online manuals for this item!

Cub Cadet Overview Questions Manuals Reviews Videos Research

Question posted by foxthg on June 29th, 2016

Csv 050 Can't Pull Cord.

can't pull cord to start. Jammed. No movement whatsoever. Used twice.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by Odin on June 29th, 2016 5:04 PM

This answer was accepted by the poster of the original question.

Odin

Member since:
April 10th, 2010

Points: 41,236,690

1,090
points

Although you didn't provide a purchase date, it seems likely that your purchase is covered by both the merchant's return policy and the manufacturer's warranty. You didn't disclose the merchant, so you'll have to look into that course on your own. Regarding warranty service, see the contact information here: https://www.contacthelp.com/Cub%20Cadet/customer-service.

Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.

Related Cub Cadet 2X 524 SWE Manual Pages

1X 221 HP Warranty Information - Page 1

...or limitations may also have a separate one (1) year from defects in addition to use the product. Replacement parts that vary in materials or workmanship. Cub Cadet shall not...or consequential loss or damage including, without limitation, expenses incurred for substitute or replacement lawn care services or for a particular purpose, applies after the applicable period of express ...

2X 524 WE Operator's Manual - Page 1

... IN PERSONAL INJURY. Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty Operator's Manual Two Stage Snow Thrower - 524 WE, 524 SWE, 526 SWE, 528 SWE & 530 SWE WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE.

2X 524 WE Operator's Manual - Page 2

... be necessary, should you how to safely and easily set up and operating your complete satisfaction at all times. If applicable, the power testing information used to establish the power rating of printing. Please read this page. It instructs you seek technical support via our web site, Customer Support Department, or...

2X 524 WE Operator's Manual - Page 3

...machine and disengage them quickly. 3. Let engine and machine adjust to outdoor temperature before starting to comply with all doormats, newspapers, sleds, boards, wires and other foreign objects,... operation. Do not wear jewelry, long scarves or other reproductive harm. Use a grounded three-wire extension cord and receptacle for ordering replacement parts. 2. Read and follow all machines...

2X 524 WE Operator's Manual - Page 4

... under the influence of ignition. 8. Extinguish all moving parts have stopped before starting engine, pull cord slowly until the auger/impeller comes to cool at too fast of your clothes... 5. Gasoline is a safety device. Allow engine to a complete stop engine before refueling. Always use a nozzle lock-open flame, spark or pilot light 14. If situations occur which can let ...

2X 524 WE Operator's Manual - Page 5

... and disengage properly and adjust, if necessary. "Use of auger/impeller. 10. Prior to storing, run machine a few minutes to prevent unintended starting. 3. Never store the machine or fuel container...avoid serious injury or death, do not modify engine in accidents, injuries or death. Never use a clean-out tool, not your hand to improper performance and compromise safety!" 6. Refer to...

2X 524 WE Operator's Manual - Page 6

... a poorly ventilated area. WARNING- WARNING- WARNING-THROWN OBJECTS This machine may appear on this manual and on the machine before refueling. ELECTRICAL SHOCK Do not use of inlet and discharge openings while machine is running . HOT SURFACE Engine parts, especially the muffler, become extremely hot during operation. Allow engine and muffler...

2X 524 WE Operator's Manual - Page 9

... 3-10. Assembly & Set-Up 9 Make sure to achieve further engagement of the chute control rod into the pinion gear. Figure 3-9 NOTE: The second hole is used to line up with your other hand to the left of the dash panel with wing nut, clevis pin, and bow-tie cotter pin arrow...

2X 524 WE Operator's Manual - Page 10

... a gravel surface, keep the skid shoes in position for recommended pressure. See Figure 3-13. Refer to operate the snow thrower on the auger housing. • Use a middle or lower position when the area to be cleared is uneven, such as necessary. Refer to operating the snow thrower. NOTE: Equal tire pressure...

2X 524 WE Operator's Manual - Page 11

... the engine. See Figure 3-14. Pivot the chute upward or downward before releasing the auger control. Section 3 - Perform all instructions below. In a well-ventilated area, start engine. Chute Assembly NOTE: Upper chutes on the left side of rotating, immediately return to the Engine Operator's Manual packed with 4-Way Chute Control are...

2X 524 WE Operator's Manual - Page 12

...Set-Up & Assembly section. When engaged, the augers rotate and draw snow into the auger housing is started. 12 Skid Shoes Position the skid shoes based on gravel or crushed rock surfaces. Controls and Features Drive ... illustrated in the right side of the handle panel and is used to determine ground speed and direction of travel. Shift Lever The shift lever is located in Figure 4-1.

2X 524 WE Operator's Manual - Page 13

...system. To turn left. The drive control also locks the auger control so that you wear gloves when using the heated grip. Failure to do so will remain engaged. CAUTION: Operate the snow thrower in increased wear... against the handle to stop. Release to engage the augers and start snow throwing action. If the auger control is recommended that you are located on the right handle.

2X 524 WE Operator's Manual - Page 14

...the joy-stick to the right or to the rear of the auger housing, reinsert the key and start the snow thrower's engine. The chute directional control is located on the left side of the dash...pivot the joy-stick forward or backward. 14 Section 4 - Stop the engine. Controls and Features Never use your hands to safely clean the chute assembly and chute opening: 1. The chute clean-out tool is ...

2X 524 WE Operator's Manual - Page 15

... foreign object or ice jam, the snow thrower is recommended that the pins may shear. To Engage Drive 1. Squeeze the drive control against the left handle. To Engage Augers To engage the augers and start throwing snow, squeeze the ... Equipped) CAUTION: It is designed so that you wear gloves when using the heated grip. See Figure 5-2. To activate the heated grips, move the switch found on...

2X 524 WE Operator's Manual - Page 16

... both wheels. Auger Shaft At least once a season, remove the shear pins from the auger shaft. Spray lubricant inside of carriage bolts are subject to use the other edge To remove skid shoes: 1. Shave Plate and Skid Shoes The shave plate and skid shoes on this machine have two wear edges...

2X 524 WE Operator's Manual - Page 18

... 18 Section 6 - Chute Control Rod To adjust the chute control rod, proceed as follows: 1. Pull out the chute control rod until the hole in it lines up " position, the cable should NOT ... adjustment of the engine and the snow thrower. Store in an unventilated area, rustproof the machine using a light oil or silicone to verify proper adjustment has been achieved. Clean the exterior of the...

2X 524 WE Operator's Manual - Page 21

Stop Bolt Friction Wheel Removal (524 WE) If the snow thrower fails to drive with the drive control engaged, and performing ...Slip the drive belt off the pulley and between the friction wheel disc and friction wheel. Friction Wheel Inspection (524 SWE, 526 SWE, 528 SWE & 530 SWE) If the snow thrower fails to drive with the drive control engaged, and performing the drive control cable adjustment...

2X 524 WE Operator's Manual - Page 23

.... 2. Remove object from gas cap. Refer to CHOKE position. 2. Extension cord not connected (when using electric start button, on engine. 1. Engine not primed. 5. Connect and tighten spark... shear pin(s). 1. Friction wheel worn. 1. Troubleshooting 8 Problem Cause Remedy Engine fails to start Engine running on CHOKE. 2. Prime engine as directed in fuel system. 4. Refer to ...

2X 524 WE Operator's Manual - Page 25

... & Accessories 10 The following attachments and accessories are available for your snow thrower for information regarding price and availability. Model Number Description 929-0071A Extension Cord, 110V 753-05762A Heated Grips* OEM-390-679 Drift Cutter Kit OEM-390-995 Snow Thrower Protective Cover 490-241-0013 Snow Thrower Auger and...

2X 524 WE Operator's Manual - Page 28

...substitute or replacement lawn care services or for a period of one (1) year from the installation or use of original retail purchase or lease. Cub Cadet LLC, P.O. For non-commercial use: Cub Cadet ... in accordance with the Operator's Manual furnished with respect to new merchandise purchased and used in the United States, its possessions and territories, and by MTD Products Limited with...