Craftsman 21500 Support Question
Craftsman 21500 Support Question
Find answers below for this question about Craftsman 21500 - Oscillating Spindle Sander.Need a Craftsman 21500 manual? We have 1 online manual for this item!
Question posted by sherm54806 on March 10th, 2015
Are All Parts Available For The 21500?
The Sears 351 215000 Drum Sander is not available anymore. Are all of the parts available?
Current Answers
Answer #1: Posted by TechSupport101 on March 11th, 2015 9:48 AM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,305
Member since:
May 24th, 2013 Points: 12,171,305
The parts for the tool does not appear offered anywhere else apart from Sears but you can complete and submit the contact form here http://www.craftsman.com/cscontactus/nb-100000000227055 for possible redirection to your nearest authorised Craftman service center that may just be able to help you with the issue.
Related Craftsman 21500 Manual Pages
Operation Manual - Page 1
SAFETY
ASSEMBLY
OPERATION
MAINTENANCE
Operator's Manual
Oscillating Spindle
SANDER Model No.
351.215000
CAUTION: Read and follow
all Safety Rules and Operating Instructions before First Use of this manual with tool. www.sears.com/craftsman
25759.00 Draft (01/22/08)
PARTS LIST
ESPAÑOL Keep this Product.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Operation Manual - Page 2
...tool's operation, application and
specific limitations. • Use recommended accessories (refer to a complete stop. • Do not overreach. Sears... should be available for commercial ...tool until it was not designed. • Disconnect tool when changing sanding drum. • Avoid accidental start-up. Your risk from the date of moving parts and sanding surfaces. • Never leave tool...
Operation Manual - Page 3
...and 3″)
D
E
A
B C
Figure 1 - Unpacking Sander
ASSEMBLY
Refer to loosen.
MOUNT SANDER Refer to order replacement parts. There must seat on sleeve securely so that neither operators nor bystanders will not spin loose on a workbench or a tool stand (see Recommended Accessories, page 9) using the tool.
• Sander can be installed on spindle. Knob must be enough room...
Operation Manual - Page 4
...all drums, inserts and washers. A temporary 3-prong to 2-prong grounding adapter (see Figure 7) is available for connecting plugs to whether the tool is properly grounded.
• This tool ... accordance with National Electric Code and local codes and ordinances. POWER SOURCE WARNING: Do not connect sander to prevent unauthorized use a 3-prong to Figures 6, 7 and 8, pages 4 and 5. Properly...
Operation Manual - Page 5
... stores or catalog. Up to 25 ft 18 25 to the up to fit Sears wet/dry vacuums.
SPECIFICATIONS Spindle diameter Drum diameters 1″, 1½″, 2″ and 3″ Drum length 4½″ Spindle stroke 1″ Spindle oscillation 30 SPM Spindle speed 1725 RPM Table diameter 18″ Table height 14½″ Dust port diameter 2.086″...
Operation Manual - Page 6
...drums clean. The sander can be turned off but cannot be locked from unauthorized use by locking the switch. To lock the switch:
• Turn the switch to repair motor may prevent the spindle from oscillating completely, causing damage to clean painted parts, rubber parts... grease to use of dust. KEEP TOOL IN REPAIR • If power cord is available at the ON position, the switch can...
Operation Manual - Page 7
... loose
Wood burns while sanding; Damaged or loose oscillating
mechanism
Excessive noise Note: Normally operating sander does make some noise
Spindle and motor not aligned properly
CORRECTIVE ACTION 1. Replace capacitor 1. Install correct fuses or circuit breakers
1. Request a voltage check from the power company
Reduce load on drum
1. Correct the low line voltage conditions 3. Reduce...
Operation Manual - Page 9
...PARTS LIST FOR SANDER
KEY NO.
1 2
3
4
5
6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
PART..., 80, & 120 grit) 9 - 24142
PARTS LIST
9
Knob
1
Drum Washer
1
(set of 5: ¾″, 1″, 1½″...Seal
1
6003ZZ Ball Bearing*
1
Bearing Retainer
1
Spindle
1
5-0.8mm Fiber Hex Nut*
1
Bushing (...Standard hardware item available locally Δ...
Operation Manual - Page 12
...sears.com www.sears.ca
Our Home
For repair of carry-in your nearest
Sears Parts & Repair Service Center
1-800-488-1222 (U.S.A.)
www.sears.com
1-800-469-4663 (Canada)
www.sears.ca
To purchase a protection agreement on a product serviced by Sears...pour service en français:
1-800-LE-FOYERMC
(1-800-533-6937) www.sears.ca
® Registered Trademark / TM Trademark / SM Service Mark of home ...
Similar Questions
Looking For Parts List Or Repair Instructions For The Magazine For Brad Nail
hex screw came loose at top of magazine, need exploded parts list/diagram
hex screw came loose at top of magazine, need exploded parts list/diagram
(Posted by ajgiv99 3 years ago)
Engine Replacement For A 1955 Craftsman 131.8250.
I have an old craftsman lawn mower 1955, MN 131.8250 and would like to replace the engine. The old o...
I have an old craftsman lawn mower 1955, MN 131.8250 and would like to replace the engine. The old o...
(Posted by jkinney6 8 years ago)
Replacement Part
I have an older craftsman garage door opener. The wall push button does not work and the part is not...
I have an older craftsman garage door opener. The wall push button does not work and the part is not...
(Posted by hleblanc 8 years ago)
Is This Sander Still Available For Purchase?
(Posted by pkrusac 10 years ago)
Replacement Parts Available For Sears Compressor 28 75116?
Drive train parts and repair instructions needed for model 28 75116 compressor
Drive train parts and repair instructions needed for model 28 75116 compressor
(Posted by randallcole 13 years ago)