Cisco SPA112 Support Question
Cisco SPA112 Support Question
Find answers below for this question about Cisco SPA112.Need a Cisco SPA112 manual? We have 2 online manuals for this item!
Question posted by Anonymous-102214 on March 9th, 2013
How Do You Do Speed Dail On Spa112.thx
The person who posted this question about this Cisco product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Cisco SPA112 Manual Pages
Administration Guide - Page 6
...open standard so there is an intelligent low-density Voice over broadband or high-speed Internet connections.
This chapter provides more information about the features of the product .... The ATA can be used with all ITSPs that enables carrier-class residential and business IP Telephony services delivered over IP (VoIP) gateway that support SIP. 1
Getting Started with the Cisco ...
Administration Guide - Page 7
... that you install your phone
• Optional: Uninterruptible Power Supply (UPS) to the Internet.
• An active Voice over IP (VoIP) account from an Internet Telephony Service Provider (ITSP). This account provides access to provide backup power
Cisco SPA100 Series Phone Adapters Administration Guide
7
Voice Lines
2
SPA122 2
-
1
1
2
Description
2 Port Phone Adapter...
Administration Guide - Page 9
This may include network and service provider data. Connect to restart the unit.
SPA112
1
SPA122
Feature RESET
PHONE 1, PHONE 2 (gray) ETHERNET (yellow) SPA122 Only INTERNET (blue)
Description Using a paperclip or similar object, press this button briefly to a broadband network ...
Administration Guide - Page 11
... Administration Guide
11 For more information, continue to Overview of the ATA. STEP 4 In the Address bar, enter the IP address of the ATA.
• SPA112: Use the built-in for most DSL service). Press the star key four times (****). Getting Started with limited access to hear the IP address.
•...
Administration Guide - Page 26
... require that you previously registered your Service Provider. If you register a MAC address in the navigation tree.
Configuring the Network
Advanced Settings
3
Field Flow Control
Speed Duplex
Description
Flow control is recommended to choose the appropriate mode for the traffic. Choose Enabled to enable this feature, or choose Disabled to abandon...
Administration Guide - Page 35
... input events (such as on/off hook or hook flash) Because the ATA uses the Session Initiation Protocol (SIP), it is equipped with most Internet Telephony Service Provider (ITSP) offerings. Configuring Voice
Getting Started with Voice Services
4
Understanding Voice Port Operations
The ATA allows calls to be custom provisioned within a wide...
Administration Guide - Page 36
... proxy server. Cisco SPA100 Series Phone Adapters Administration Guide
36 For more information, see Audio Configuration, page 104. SIP Proxy Redundancy
In typical commercial IP Telephony deployments, all calls are compatible and interoperable, but not identical.
These codecs provide the highest narrow-band voice quality and uses the most bandwidth of...
Administration Guide - Page 39
... configure the length of time allowed for impedance mismatch. For more digits are enabled by momentarily removing the voltage between the telephone and the IP Telephony gateway phone port can lead to near -end echo canceller that compensates for detection of a dialed string, and a short timeout, signaling that more information, see...
Administration Guide - Page 41
... gateway for T.38 with Voice Services
4
STEP 5 In the Audio Configuration section, enter the following steps:
STEP 1 Verify that your settings or click Cancel to a speed between two ATAs.
codec only: yes • Silence Supp Enable: no • Echo Canc Enable: no vad
Fax Troubleshooting If you are using modem passthrough...
Administration Guide - Page 84
... feature. Paging Code
Used for a conference call . Default setting: *16.
Enter the code for paging other clients in the group.
Default setting: *85.
Speed Dial Act Code Assigns a speed dial number. Default setting: *17.
Secure One Call Deact Code
Makes the next outbound call secure. (It is redundant if all outbound calls...
Administration Guide - Page 100
...Attended Call Transfer Service. Default setting: Yes
Enable VMWI Service (FSK) Default setting: Yes
Enable Speed Dial Service. See the Referral Services Codes parameter For more information. MWI is available only if ...Serv Three Way Conf Serv Attn Transfer Serv Unattn Transfer Serv MWI Serv VMWI Serv Speed Dial Serv Secure Call Serv
Referral Serv
Description
Enable Call Waiting Caller ID Service ...
Administration Guide - Page 109
...
Call Waiting on/off . Configuring Voice
Configuring Voice Settings
4
Field
Cfwd No Ans Delay
Description
Delay in sec before Call Forward No Answer triggers. Speed Dial Settings
Field Speed Dial 2-9
Description
Target phone number (or URL) assigned to forward a PSTN caller matching the Cfwd Sel x Caller parameter. Default setting: yes
Cisco SPA100...
Administration Guide - Page 115
SPA112: Web Access Management
Web access to the configuration utility is 80. For example, with the HTTPS protocol, a WAN IP address of the ATA, and the ...
Administration Guide - Page 126
... and received, the percentage of times to test connectivity between the ATA and a destination. STEP 3 Choose the number of packet loss, and the round-trip speed. Diagnostics
The ATA includes two built-in the log file.
Administration Guide - Page 139
You need a cable/DSL modem and a high-speed Internet connection. My modem does not have an Ethernet port, then it is case sensitive.
Connect your telephone line to the cable modem.
STEP 3 Start a ...
Quick Start Guide - Page 1
Quick Start Guide
Cisco SPA100 Series Analog Telephone Adapters
SPA112 Two Port Phone Adapter SPA122 ATA with Router
Package Contents • Analog Telephone Adapter • Ethernet Cable • Power Adapter • Quick Start Guide • Product CD-ROM
Quick Start Guide - Page 2
...; Ethernet cable to connect to your broadband network device • Phone to connect to your SPA112/122 • Phone cable to connect your phone • Optional: Uninterruptible Power Supply (UPS...Top Panel
2
Cisco SPA100 Series Analog Telephone Adapters Welcome
Thank you have the following models: • SPA112 Two-Port Phone Adapter: 2 FXS ports and 1 10/100 WAN
port. • SPA122 ATA...
Quick Start Guide - Page 5
... can connect your computer to the ETHERNET (Yellow) port of the ATA. STEP 4 In the Address bar, enter the IP address of the ATA.
• SPA112: Use the ATA's IVR or your router's configuration utility to establish your operating system. For more information, refer to obtain an IP address automatically. You...
Similar Questions
Info Pap2t&spa112
what is the difference between pap2t and SPA112
what is the difference between pap2t and SPA112
(Posted by asgherislam 11 years ago)
Hello Can I Get A Full Picture Of How To Set Up My New Spa112 At Home Please
(Posted by ojbarwary1972 11 years ago)
How To Setup Caller Id On Cisco Spa112
how to setup caller Id for sip calling on cisco spa112 ?
how to setup caller Id for sip calling on cisco spa112 ?
(Posted by sohag382 11 years ago)