Home » Canon » Printers » Canon PIXMA MG5420

Canon PIXMA MG5420 Support Question

Find answers below for this question about Canon PIXMA MG5420.
Need a Canon PIXMA MG5420 manual? We have 2 online manuals for this item!

Canon Overview Questions Manuals Reviews Videos Research

Question posted by kasshop on February 20th, 2015

How To Set The Default Paper Tray To The Bottom Tray?

Most times that I try to print an 8.5x11 document, the printer defaults to the upper photograph tray instead. How can I change the "default" to be the bottom full-size paper tray? This problem occurs even when the software (e.g., Pages) allows me to specify printing on the bottom tray. Aarrgghh

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by TechSupport101 on February 24th, 2015 8:10 AM

TechSupport101

Member since:
May 24th, 2013

Points: 12,171,325

90
points

Hi.

Go to the machine control panel.
Select Setting and Registration.
Select Function Setting.
Select Common Setting.
Select Paper Feed Setting.
Select Paper Drawer Auto Selection On/Off.
Select the desired tray function(Copy, Print, Access Stored Files, Receive/I-Fax, or Other).
Select the Tray incoming jobs are to pull from.
Select On.
Turn Off all other trays.
Press OK twice.
Select Close.

www.satechhelp.co.za

Related Canon PIXMA MG5420 Manual Pages

Setup Guide - Page 2

Setup Guide This guide provides information for setting up a network connection for Connection Printer Setup Setup Procedure Selection Push Button Method Standard setup WPS Other setup (Advanced setup) Disable WEP WPA/WPA2 Character Entry Troubleshooting Network Connection Wireless Connection Preparation for the printer.

Setup Guide - Page 3

.... • The configuration, router functions, setup procedures and security settings of the network device vary depending on . Change the security protocol for Connection Before Starting Wireless Connection Setup 1. b Printer Setup 1. Be sure to the "IEEE802.11 n only" mode, WEP or TKIP cannot be lit. Network Connection Wireless Connection a Preparation for your device to...

Setup Guide - Page 4

...-Fi Protected Setup). * If the Push Button Method screen is enabled. 2. Use the or button (A) to the Network by Entering the Access Point's Settings Directly on the printer When you are unsure if your access point or router supports this technology, press the Stop button. Push Button Method → d-A Select the most...

Setup Guide - Page 5

For details on the printer within 2 minutes. When the left screen appears, press the OK button. d-A Push Button Method d Connection Using WPS 1. Press the OK button on ... The (blue) Wi-Fi lamp on the access point. The network connection setup is now complete. Press and hold the WPS button on the printer ﬂashes while searching for or connecting to the access point manual. 2.

Setup Guide - Page 6

..., then press the OK button. 4. Character entry is case-sensitive. 9. Character entry is case-sensitive. 7. One of the screens below will be displayed on the printer. 5. Enter the network password (WEP key or passphrase). The network connection setup is correct. Press the OK button. 6. Make sure that the network password is...

Setup Guide - Page 7

... button method. 4. The network connection setup is now complete. Press the OK button. 3. Press the OK button. 6. d-C WPS d Connection Using WPS 1. For details on the printer ﬂashes while searching for or connecting to the access point manual. 7. Press and hold the WPS button on the...

Setup Guide - Page 11

... You can enter the characters when the keyboard is displayed on the printer. Follow the procedure below. 1. You can enter the characters when the keyboard is case sensitive so press the center Function button (A) accordingly to switch between lower case, upper case and numeric characters. 2. Use the buttons (B) to select a character from...

Setup Guide - Page 12

...name in the Select access point screen. "WPA/WPA2 Enterprise" is not supported on this printer. • For details on how to the manual supplied with the access point or ...to change the security protocol (encryption standard) and configure wireless connection settings again. If the problem is not resolved, there may be entered on the printer directly. • If "WPA/WPA2 Enterprise" is set ...

Setup Guide - Page 14

...the access point, refer to change the settings of the printer. 1. Select LAN settings > Confirm LAN settings > WLAN setting list to display WLAN setup...change settings so that the WEP key entered for the access point is not resolved, there may be accepted. Press the HOME button. 2. Select Device settings, then press the OK button. 4. Press the HOME button (A). 2. If the problem...

Setup Guide - Page 15

... press the right Function button. 3. If the problem is not resolved, there may be accepted. See also the sections below: • If the access point is configured to communicate using IEEE802.11n standard only and encryption is set to check or change the settings of the printer. 1. See also the sections below to check the...

Setup Guide - Page 17

...occurs. For details on only one access point.  Failed to the manual supplied with the access point or contact its manufacturer.  Timeout error. The screen appears when WPS setup was not completed within a specified time...on how to check the settings of the access point, refer to connect. Check the access point settings, then configure WPS settings again. If the network ...

Setup Guide - Page 18

... IEEE802.11b? If the problem is not resolved, there may be entered on the printer directly. • If "WPA/WPA2 Enterprise" is set as the security protocol (encryption... standard) on how to the manual supplied with the access point or contact its manufacturer. For details on the access point, change...

Setup Guide - Page 20

... LAN settings > WLAN setting list to the access point. For details on how to check or change the WEP key number of the access point, refer to check the MAC address of the access point can be other causes. Follow the procedure below : • If the DHCP function of the printer directly. If the problem...

Setup Guide - Page 21

... the OK button. 3. Follow the on how to check or change the settings of the access point, refer to proceed with the access point or contact its manufacturer. Press the HOME button (A). 2. To specify the IP address of the printer and configure wireless connection settings again. Select IP address, then press the OK button...

Setup Guide - Page 22

... resolved, there may be other causes. Press the HOME button. 2.  WPA/WPA2  Failed to connect to check the MAC address of the printer. 1. If the problem is Not Displayed Automatically Refer to change settings so that the passphrase entered for the access point is not resolved, there may be accepted. If the...