Brother International JX2517 Support Question
Brother International JX2517 Support Question
Find answers below for this question about Brother International JX2517.Need a Brother International JX2517 manual? We have 2 online manuals for this item!
Question posted by sewraggediesandprims on November 21st, 2013
How To Get Thread In Needle
How do i get the thread in the needle to bring the thread in the bobin to the sewing are
Current Answers
Related Brother International JX2517 Manual Pages
Users Manual - English and Spanish - Page 2
... careless movements, otherwise you may fall, resulting in injuries.
5 Special care is required when
sewing:
• Always pay close attention to the needle. Do not pull on the unit. Keep ventilation openings of the electrical outlet. WARNING - Plug the machine directly into the electrical outlet.
• Never drop or insert any opening.
•...
Users Manual - English and Spanish - Page 3
... occurs or adjustment is intended for household use or store the machine near children.
• The plastic bag that they do not deflect the needle and cause it could cause the needle to break.
• Do not push or pull the fabric when sewing, and follow the troubleshooting table in the back of the...
Users Manual - English and Spanish - Page 4
...attachment 5
USING YOUR SEWING MACHINE 6 Connecting plugs 6 Main power and sewing light switch 7 Foot controller 7 Checking the needle 7 Replacing the needle 7 Changing the presser foot 8
THE CONTROLS 9 Pattern selection dial 9 Patterns and stitch names 9 Reverse sewing lever 10
THREADING THE MACHINE 11 Winding the bobbin 11 Lower threading 13 Lower threading (for the plug supplied...
Users Manual - English and Spanish - Page 6
...SEWING MACHINE
THE MAIN PARTS
3
2
1
4
B
5
A
C
6
0
7
8
9
1 Bobbin winder (Page 11) This winds the thread onto the bobbin for 220-240V area
The foot controller part code differs depending on certain models.)
8 Flat bed attachment with accessory compartment (Page 5)
9 Presser foot (Page 8)
0 Reverse sewing lever (Page 10) Push this to control the sewing...lower the needle.
E ...
Users Manual - English and Spanish - Page 13
... sure you do not cut the excess thread completely before winding the bobbin, when the thread runs low it may occur when the thread is not a malfunction.
● The needle bar does not move when you slide the bobbin winder shaft to the right.
Note
● When the sewing machine is started or the handwheel is...
Users Manual - English and Spanish - Page 14
..., it may cause the thread tension to be injured. KNOWING YOUR SEWING MACHINE
Lower threading
Install the bobbin wound with your finger, and then
pass the thread through
the tension-adjusting spring of the thread, push the 5 bobbin down with thread. • For more details on page 17 after threading the upper thread.
Raise the needle by the arrow.
Refer...
Users Manual - English and Spanish - Page 16
... pin and cause the needle to "FABRIC, THREAD, AND NEEDLE COMBINATIONS" on the wheel
15 Turn off the machine.
1
Raise the presser foot lever.
2
Pull up .
• If the needle is not correctly raised, the sewing machine can not be threaded.
KNOWING YOUR SEWING MACHINE
Upper threading
2
2
3 4
1 5
1 Spool pin 2 Thread guide (back) 3 Thread guide (front)
4 Thread take-up lever 5 Mark...
Users Manual - English and Spanish - Page 17
...)
Note
● Make sure you raise the presser foot lever and the thread take -up lever before you feed the upper thread.
● If you incorrectly feed the thread you may cause sewing problems.
16
Make sure you raise the needle by holding the thread from the spool 5 with your left
as shown in the 6 following...
Users Manual - English and Spanish - Page 18
... the 2 direction of the arrow, and leave it there
without drawing up the bobbin thread.
KNOWING YOUR SEWING MACHINE
Drawing up the lower thread
While lightly holding the end of the upper 1 thread, slowly turn the handwheel toward the back of
the machine under the presser foot.
1 2
1 Upper thread 2 Lower thread
17 Before you (counterclockwise) by hand to 3.
Users Manual - English and Spanish - Page 19
... Tweed
Thread Type Cotton thread Synthetic thread Silk thread Cotton thread Synthetic thread Silk thread
Cotton thread
Synthetic thread Silk thread
Size 60-90
50 60-90
50 30 50 50-60
Size of the fabric or thread. The wrong combination may cause machine malfunction. and the higher the needle number, the thicker the needle.
■ Ball point needle Use the ball point needle when sewing on...
Users Manual - English and Spanish - Page 20
...out about 5 cm (2 inches) of thread toward you
(counterclockwise) so that the needle does not hit basting pins or other objects during sewing, otherwise the needle may be damaged and you may be injured...the mark on the wheel points up. Starting sewing
Raise the presser foot lever.
5
Turn on the machine while pressing down the foot controller.
The needle
may break and you may be damaged. ...
Users Manual - English and Spanish - Page 21
...needle to "Reverse sewing lever" on the foot controller.
9
X The machine starts sewing. While holding the end of the thread and 7 the fabric with your left side of the c machine, and then pass the threads through the thread cutter to cut them.
.
1
Sewing... higher to bring the presser foot to change the sewing direction, and then raise the presser foot lever. Trial sewing
A trial piece of fabric ...
Users Manual - English and Spanish - Page 24
... looser upper-thread tension to the right position of Zigzag (Satin) Stitch (number 5).
4 Zigzag Stitch
2 (1/16)
5 (3/16)
Zigzag (Satin)
5
Stitch
0.5 (1/32) 5 (3/16)
23
BUILT-IN STITCHES
3 BUILT-IN STITCHES
Straight stitching
Straight stitches are used for sewing plain seams.
Stitch Name
Pattern
Stitch Length [mm (inch)]
Straight Stitch
6
(Center Needle Position...
Users Manual - English and Spanish - Page 31
... and applying it as a decoration.
Baste the cut design to gather the 3 material.
If the needle hits the zipper, the needle may be injured. Carefully sew around the edge of 2 straight stitches.
5
Pull the lower threads to the fabric.
1
Sew a single row (or many rows) of the 2 design with a zigzag stitch.
30 CAUTION
● Make...
Users Manual - English and Spanish - Page 32
...
● Do not turn on the needle 4 plate. Place the darning plate on the machine while pressing down the foot controller.
X Use scissors to cut the upper thread and the bobbin thread at the end of the
8 stitching to the machine.
31 USING ATTACHMENTS AND APPLICATIONS
USING OPTIONAL ACCESSORIES
L
Sewing buttons
Stitch Name
Pattern
Stitch Length...
Users Manual - English and Spanish - Page 36
... case aligns with the ● mark
on the machine as shown below.
1 1
2
2
• Align the ▲ and ● marks.
1 Screws
• Make sure that you fit the bobbin case properly, otherwise the needle may suffer. otherwise the upper thread may become tangled, the needle may break, or sewing performance may break.
3
1 ▲ mark 2 ● mark...
Users Manual - English and Spanish - Page 37
... screw.
8
The needle is correct
appropriate for the type of stitch that you need additional help, the Brother Solutions Center offers the latest FAQs and troubleshooting tips. You can solve most problems by yourself. Symptom
Possible cause
How to sew. Use the foot controller properly.
7
Fabric being
sewn with the
machine
Thread is tangled...
Users Manual - English and Spanish - Page 38
... the bobbin case.
You have not used a bobbin that you are appropriate for this machine. Correctly install the needle.
Thread the upper thread and wind the bobbin thread properly. Possible cause
The needle is incorrect. Attach the presser foot holder properly. Sew with stabilizer material under the fabric.
You have not used the right combination of stitch...
Users Manual - English and Spanish - Page 39
... for the type of fabric. Remove the tangle thread.
The presser foot that you want to sew.
Correctly install the needle. Choose a thread and needle that are appropriate for the type of fabric, thread and needle.
You have not used the right combination of fabric.
How to sew. Choose a thread and needle that are appropriate for the type of stitch...
Users Manual - English and Spanish - Page 40
... quick-set bobbin 14 17
M Main parts 5 Main power 7 Maintenance 34
N Needle
checking 7 combinations with fabric and thread ......... 18 replacing 7
O Overedge stitching 25
P Pattern selection dial 9 Patterns 9 Presser foot changing 8
, Q
Quick-set bobbin 14 17
39
R Race cleaning 34 Reverse sewing lever 10
, S
Spool pin 11 15 Stitches
built-in 23 names 9 Straight...
Similar Questions
Winder Tire
Brother JX2517 :Where can I find a winder tire? What is the part number for the winder tire? Is ther...
Brother JX2517 :Where can I find a winder tire? What is the part number for the winder tire? Is ther...
(Posted by rs100k 1 year ago)
How Do I Take Apart Brother Sewing Machine Jx2517. To Reattach The Belt?
(Posted by louisianajean 8 years ago)
Underside Thread Tangled.
This was working until bobbin thread ran out. New bobbin thread comes thru single-hole side, from in...
This was working until bobbin thread ran out. New bobbin thread comes thru single-hole side, from in...
(Posted by stevensonrosemarie 8 years ago)
Where Is A Parts Guide Or Service Manual For Brother Jx2517 Sewing Machine?
the inside of my brother JX2517 sewing machine broke. Its a plastic piece,gear, at end by the needle...
the inside of my brother JX2517 sewing machine broke. Its a plastic piece,gear, at end by the needle...
(Posted by Discogypsy 9 years ago)
Sewing Machine Lx 2500 How To Stread The Bobin
(Posted by patkaNwdug 10 years ago)