Brother International JX2517 Support Question
Brother International JX2517 Support Question
Find answers below for this question about Brother International JX2517.Need a Brother International JX2517 manual? We have 2 online manuals for this item!
Question posted by stevensonrosemarie on June 19th, 2015
Underside Thread Tangled.
This was working until bobbin thread ran out. New bobbin thread comes thru single-hole side, from inside to outside [no instructions anywhere relating to whether bobbin sides are relevant]. Bobbin is threaded thru tension bar and tracked as per manual. Same needle and thread as before. Why is underside tangled?
Current Answers
Answer #1: Posted by waelsaidani1 on June 26th, 2015 5:08 AM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,777
Member since:
May 12th, 2013 Points: 19,501,777
Hello refer here for help: http://support.brother.com/g/b/faqend.aspx?c=au&lang=en&prod=hf_ns55eas&faqid=faqh00100036_001
Related Brother International JX2517 Manual Pages
Users Manual - English and Spanish - Page 4
...attachment 5
USING YOUR SEWING MACHINE 6 Connecting plugs 6 Main power and sewing light switch 7 Foot controller 7 Checking the needle 7 Replacing the needle 7 Changing the presser foot 8
THE CONTROLS 9 Pattern selection dial 9 Patterns and stitch names 9 Reverse sewing lever 10
THREADING THE MACHINE 11 Winding the bobbin 11 Lower threading 13 Lower threading (for the plug supplied...
Users Manual - English and Spanish - Page 5
... be purchased separately. Part Name
1 Darning Plate 2 Button sewing foot "M"
3 Walking Foot
4 Quilting Foot
5 1/4-inch Quilting Foot
Part Code
Americas Others
XC6063-021
XE2137-001
SA107
F034N: XC2165-002
SA129
F005N: XC1948-052
SA125
F001N: XC1944-052
No.
Part Name
1
Zigzag foot "J" (on machine)
2 Buttonhole foot "A"
3 Zipper foot "I"
4
Bobbin (One is on the...
Users Manual - English and Spanish - Page 6
... machine.
4 Thread take-up lever (Page 16)
5 Upper tension-control dial (Page 22) This controls the tension of the upper thread.
6 Thread cutter (Page 20) Pass the threads through the thread cutter to cut them.
7 Quick-set bobbin (Page 14, 17) (This is only available on certain models.)
8 Flat bed attachment with accessory compartment (Page 5)
9 Presser foot (Page 8)
0 Reverse sewing...
Users Manual - English and Spanish - Page 7
... the power cord are firmly inserted into the electrical outlet and the power supply jack on the machine.
● Do not insert the plug on the cord. b
a
Note
● If a power outage occurs while the sewing machine is in poor condition. ● Turn off the main power and remove the plug in a polarized...
Users Manual - English and Spanish - Page 8
... sewing machine needles for smooth sewing.
1 2
1 Turn on (toward the 'I' mark) 2 Turn off . Checking the needle
The sewing needle must always be used on the machine with a bent needle. The product code is mentioned on the machine rating plate.
■ Checking the needle correctly Put the flat side of any bent needles safely.
1
2
1 Parallel space 2 Level surface (bobbin...
Users Manual - English and Spanish - Page 9
...hole in line with the slot on what you want to change the presser foot. If you
(counterclockwise) so that the mark on the controller, the machine will have to sew... damaged.
With the flat side of the needle toward the 5 back of the sewing machine may be damaged.
3... machine before you may cause
accident or injury.
1 Use a screwdriver
• Do not use presser feet that the bar ...
Users Manual - English and Spanish - Page 10
...3.3 (3/16)
23, 30, 31, 33
9 If the presser
foot is in the correct place, the bar should snap in.
■ Presser foot installation orientation
1
2
1 Shank 2 Bar
THE CONTROLS
CAUTION
● If the presser foot is in either direction.
2
1
1 Pattern selection dial..., which may be damaged. KNOWING YOUR SEWING MACHINE
Lower the presser foot lever and fix the 5 presser foot onto the shank.
Users Manual - English and Spanish - Page 12
...-151). KNOWING YOUR SEWING MACHINE
THREADING THE MACHINE
Winding the bobbin
CAUTION
● We designed the bobbin that comes with this machine. Then, pass the thread around the pre-tension disk and pull the thread in completely.
11
CAUTION
● If the spool of 1 thread on this pin.
3 Bobbin
While holding the thread from other bobbins may tangle on the thread guide. If you...
Users Manual - English and Spanish - Page 13
... personal injury or damage to the machine.
CAUTION
● Not winding the bobbin properly may cause the thread tension to loosen, and may tangle around the bobbin. Pass the end of the thread through the hole
Trim the excess thread above the bobbin.
3 on the bobbin from the inside of the bobbin. 7 • Leave 1 cm (1/2 inch) of the thread, 6 gently press the foot controller...
Users Manual - English and Spanish - Page 14
... details on the foot controller and the machine starts to "Drawing up the lower thread before threading the lower thread.
• See page 11 for the details about bobbin winding. KNOWING YOUR SEWING MACHINE
Lower threading
Install the bobbin wound with your finger, and then
pass the thread through
the tension-adjusting spring of the thread comes
out from the cover toward you...
Users Manual - English and Spanish - Page 15
... (1 and 2).
While lightly holding down the bobbin 2 with a quick-set bobbin)
Replace the bobbin cover. When sewing gathers or darts, you to cut it may cause incorrect thread tension.
1
1 Tension-adjusting spring
14 Lower threading (for models equipped with your right hand as shown, guide the
thread through the tension-adjusting spring of the bobbin case, it with the cutter (3).
•...
Users Manual - English and Spanish - Page 16
...not correct, the thread may become tangled or the needle may tangle on the spool pin and cause the needle to "FABRIC, THREAD, AND NEEDLE COMBINATIONS" on the wheel
15 If the upper threading is not correctly raised, the sewing machine can not be threaded. KNOWING YOUR SEWING MACHINE
Upper threading
2
2
3 4
1 5
1 Spool pin 2 Thread guide (back) 3 Thread guide (front)
4 Thread take-up...
Users Manual - English and Spanish - Page 18
...them toward the back of
the machine under the presser foot.
1 2
1 Upper thread 2 Lower thread
17 When sewing gathers or darts, you can begin sewing immediately without cutting it there
without drawing up the bobbin thread. KNOWING YOUR SEWING MACHINE
Drawing up the lower thread
While lightly holding the end of the upper 1 thread, slowly turn the handwheel toward
you (counterclockwise...
Users Manual - English and Spanish - Page 21
... the starting point of the stitching. Raise the needle by pressing the reverse sewing lever.
While holding the end of the thread and 7 the fabric with your left side of the c machine, and then pass the threads through the thread cutter to cut them.
.
1
Sewing thick fabrics
■ If the fabric does not fit under the presser...
Users Manual - English and Spanish - Page 22
... stabilizer material under the fabric and sew it . When you change fabric or thread.
Note
● When you start to sew.
■ Correct tension Correct tension is possible.
21 Slide the flat bed attachment to the left to sew onto 2 the arm, and then sew from the top.
1
1 Stabilizer material or paper
Sewing stretch fabrics
First, baste the...
Users Manual - English and Spanish - Page 24
... (1/8)
3
Zigzag Stitch
1.5 (1/16) 3.3 (3/16)
We recommend that you sew using the Straight Stitch at the beginning and end of Zigzag Stitches. (This ...sewing. When sewing a Zigzag (Satin) Stitch, use the Zigzag (Satin) Stitch for top stitching and sewing lightweight fabrics. With the pattern selection dial, the Zigzag (Satin) Stitch (number 5) can use a slightly looser upper-thread tension...
Users Manual - English and Spanish - Page 37
...; The upper thread tension is scratched. sew. breaks.
Fit the spool properly.
-
15
6
The area around the hole in the thread.
Contact your retailer or the nearest authorized service center.
- The bobbin case is too tight. Replace the bobbin case.
authorized service center. You have not used a bobbin that has been Use a bobbin that is loose. for this machine.
11...
Users Manual - English and Spanish - Page 38
.... Wind the bobbin thread properly. Choose a thread and needle that are appropriate for this machine. Use a bobbin that are appropriate for this machine. Choose a thread and needle that has been designed for the type of fabric. Adjust the tension of the upper thread.
The area around the hole in the needle plate or the presser foot is tangled.
The thread is scratched...
Users Manual - English and Spanish - Page 39
... want to sew. Adjust the tension of stitch.
Correctly install the needle.
Remove the needle plate and clean the plate and the bobbin case. If the thread is tangled, for example, in the bobbin case, clean the bobbin case. If the thread is tangled. The thread is tangled in the bobbin case. The fabric does not feed.
How to sew. Remove the tangled thread. Remove...
Users Manual - English and Spanish - Page 40
... dial 9 Patterns 9 Presser foot changing 8
, Q
Quick-set bobbin 14 17
39
R Race cleaning 34 Reverse sewing lever 10
, S
Spool pin 11 15 Stitches
built-in 23 names 9 Straight stitching 23
T Thread cutter 20 Thread tension 21
, Threading lower 13 14 upper 15 Troubleshooting 36
U Upper tension control dial 22 Upper threading 15
Z Zigzag stitching 23 Zipper insertion 29
Similar Questions
How Do I Take Apart Brother Sewing Machine Jx2517. To Reattach The Belt?
(Posted by louisianajean 8 years ago)
Where Is A Parts Guide Or Service Manual For Brother Jx2517 Sewing Machine?
the inside of my brother JX2517 sewing machine broke. Its a plastic piece,gear, at end by the needle...
the inside of my brother JX2517 sewing machine broke. Its a plastic piece,gear, at end by the needle...
(Posted by Discogypsy 9 years ago)
Brother Sewing Machine Sq9050 What Type Bobbin
(Posted by Marbl 10 years ago)
Tension Adjustment On The Brother Sewing Machine #jx5217?
How do you adjust the tension on the Brother Sewine Machine #JX5217?
How do you adjust the tension on the Brother Sewine Machine #JX5217?
(Posted by flokay8 10 years ago)
Rating
Do you have any review or rating on brother jx2517 sewing machine.
Do you have any review or rating on brother jx2517 sewing machine.
(Posted by Moelimo53 10 years ago)