Bernina 800DL Support Question
Bernina 800DL Support Question
Find answers below for this question about Bernina 800DL.Need a Bernina 800DL manual? We have 1 online manual for this item!
Question posted by goings58 on November 4th, 2013
When Overlocking Heavier Fabrics (flannel, Corduroy) One Of The Threads Skip.
When this happens, it continues to overlock, but the "security" stitch just remains unstitched and pulls along with the fabric. Then I need to go to my sewing machine and restitch that area that was missed with the security stitch. The repair service says that nothing can be done. Is this common?
Current Answers
Related Bernina 800DL Manual Pages
Manual - Page 3
Model 800 I he various parts of the machine
14 15 16
1 Free-arm cover-plate 2 Needle-plate 3 Presser-foot 4 Needle-clamp 5 Thread guide
6 Face-plate
7 Lamp switch
8
8 Take-up lever
BERNINA'
01 9
9 Winder pre-tension 10 Thread tension and thread guide
11 Tension indicator window
17
12 Thread tension control wheel
13 Carrying handle
18
14...
Manual - Page 4
... cable and the BerninaInstruction manual. Press bulb upwards, turn it clockwise. Fit special plug on and off.
Pull out light cover sideways to supply
Warning! After inserting the special combination plug for connecting Bernina sewing machines. To insert bulb, turn anti-clockwise and draw downwards.
tr
0, 4
Electrical Connectior
Connecting to change the bulb...
Manual - Page 5
... hinged latch with the handwheel high enough so that
y
y~ -,. sewing machine 800. while those for darning are numbers 80, 90 and 100
. a
I
•ti f I and 80.
ti
Needle and thread table
Needle system 705 B
very fine fine
60
70
Mercerised sewing thread (3 ply)
50
Darning thread (2 ply)
50
30-50
medium 80
50
30
strong 90...
Manual - Page 6
... top position by the hinged r is full, the winding process stops automatically. Check-up: Pull end of thread. Inserting the 0000111
Place bobbin on . The winder ist then switched on winder spindle and ...thumb and forefinger of the left . Hold bobbin case in the direction of the arrow. Draw thread from the reel clockwise round the pre-tensioning device and from there - Then re-tighten knurled ...
Manual - Page 7
... ins.). Threading the machine.
The tension centering wheel (12) can be in pin. in center = Looser tension. Hold
needle thread loosely. Lowering the feed dog. For normal sewing turn knob...sewing the thread tension does not have to the
left hand through the needle hole. BERNINA
L4 I
the zigzag and straight stitch sign.
7 For certain types
of the tension disc. Pull both threads...
Manual - Page 8
... as a thread cutter. this advantage. The lever on !" The patented Bernina presser foot clamping lever permits quick and easy changes. The Bernina principle: "Just clip it on the presser foot bar is ready for each type of the lever at hand.
8
Changing the presser feet - The presser foot is secured and the machine is...
Manual - Page 9
... knob is out of the
material. depending on zigzag 18 allows the stitch
rately adjusted with the stitch length adjusting knob (19). by turning the knob to the right - while sewing but when the machine is
stationary only if the needle is vertical (stitch length ---- 40). I
9
The line on material and
higher the number, the...
Manual - Page 10
...Buttonholes
Buttonhole foot 033 Needle: 80-70 Thread: 30 or 50
For sewing a buttonhole, thread bottom cotton through hole in finger of ...bobbin case.
10
0 12 3 4 -18
0 123 4 17
Adjustment of the Buttonhole
Two mechanical spring settings have
been built-in the middle of the foot. Hold work in for the buttonhole: one stitch...
Manual - Page 11
...pull, place the work clockwise with right hand until cords are parallel. Do not lower the foot yet.
and lift foot. If not do one stitch by turning the hand wheel towards you, bringing the needle to sew the buttonhole with reinforcing cord
Set machine.... Continue sewing as for
tonhole on a remnant of the material to be used.
Lower foot so that when the sewing
easily...
Manual - Page 12
... hold hoop correctly Not like this. Thumb facing the frame (slightly bent) side of each row Frequent thread breaking - Then pulled back a little. Weftway.
2. Same way as when writing). -
Beginners may prefer the L or M movement. poor stitch (looping moved too quickly. Always work from left to the frame. How to darn correctly
Main...
Manual - Page 13
... hoop.
It is obvious here that the area to be darned is in the center. Wrong
Correct
With the right hand keep the area of free arm. Remembering the following points:... darning foot 285
Needle: 80-70 Thread: 50
Darning fine socks (also sleeves)
Stitch width:
0
Stitch length:
0
Needle position: center
Drop feed control: lowered
Darning fine socks
Pull work over ring (not ring over ...
Manual - Page 14
...duster. Lock the bridge
locking bridge together with the hook together with a small brush
If the machine has 'been standing in the bearings will cleaned as also can now be brought into position..... the needle plate on the arm-cover.
14 During sewing
pieces of oil
bobbin case. Remove After cleaning pour a few drops of thread and fluff collect under
the needle plate and around the hook...
Manual - Page 15
... causes:
a) Motor does not function properly
a) the bottom thread tension is damag- Thread has dried out due to authorized Bernina dealer); A bad uneven needle and needs repolishing (bring your machine to fingers).
3. The sewing machine should always be at the back);
whether:
needle plate).
c) the machine is blunt or crooked;
d) the needle is cleaned properly...
Similar Questions
I Have One Question About My Bernina Overlock, #4 Threa Always Broken When I Ser
(Posted by waimills1630 1 year ago)
Hi My Bernina 440qe Keeps Giving A Thread Break Beep When No Thread Has Broken.
I have checked the bobbin and can't see a problem, I can see the sensor spring moving up and down on...
I have checked the bobbin and can't see a problem, I can see the sensor spring moving up and down on...
(Posted by brendamcfall 4 years ago)
Bernette 66 Sewing Machine
How do I thread a Bernette 66 sewing machine?
How do I thread a Bernette 66 sewing machine?
(Posted by stringpam 8 years ago)
The Second Thread On My 800dl Overlocker Keeps Breaking. I Re Thread Then It S
I am frustrated at the 2nd thread constantly breaking. I re thread and it sews fine for about 1" the...
I am frustrated at the 2nd thread constantly breaking. I re thread and it sews fine for about 1" the...
(Posted by sueo78 10 years ago)