BenQ MP610 Support Question
BenQ MP610 Support Question
Find answers below for this question about BenQ MP610 - SVGA DLP Projector.Need a BenQ MP610 manual? We have 1 online manual for this item!
Question posted by quocgiang on November 14th, 2015
Projector Mp610 Fail.
when pressing power , the white lights dim 5 seconds then turned off and the fan is still operating normally . MP610 fails on due DAD1000 main Is not ? please
Current Answers
Answer #1: Posted by TechSupport101 on November 15th, 2015 2:04 AM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,305
Member since:
May 24th, 2013 Points: 12,171,305
Hi. Please carefully look at the symptoms you are receiving against the Service Manual here http://elektrotanya.com/benq_mp610.zip/download.html to try and isolate the root cause of the projector issue and hopefully get it corrected.
Related BenQ MP610 Manual Pages
User Manual - Page 1
MP610 Digital Projector Portable Series User's Manual
Welcome
User Manual - Page 3
...Replacing the remote control battery 10
Positioning your projector 11
Choosing a location 11 Obtaining a preferred projected image size 12
How to determine the position of the projector for a given screen size: .. 13... 18 Connecting an S-Video source device 19 Connecting a composite Video source device 20
Operation 21
Start up 21 Utilizing the password function 21
To set a password 21 If...
User Manual - Page 4
...menu 33 5. Information menu 35
Maintenance 36
Care of the projector 36
Cleaning the lens 36 Cleaning the projector case 36 Storing the projector 36 Transporting the projector 36
Lamp information 37
Calculation of lamp hour 37 Warning message...25 Hiding the image 25 Remote paging operations 26 Freezing the image 26 Shutdown 26 Menu operation 27
Menu system 27 Using the menus 28 1.
User Manual - Page 7
...projector through a power
stabilizer, surge protector or
uninterruptible power supply (UPS). In areas where the mains voltage may damage your projector. However, to ensure safe use of ±10 volts occur.
Important safety instructions 1 This projector is designed
to operate safely within a mains... at the projector lens during operation. The intense light beam may fluctuate...
User Manual - Page 8
... Never replace the lamp assembly or any electronic components unless the projector is required. The product may fall, sustaining serious damage.
5. Allow the projector to cool for approximately 45 minutes prior to break on an unstable cart, stand, or table. Do not operate lamps beyond the rated life could cause them to removing...
User Manual - Page 9
... than 10000 feet.
9. Do not stand the unit on a level,
horizontal surface during operation.
- Do not place this unit on a blanket, bedding or any of a car ...place this projector in a fire.
8. Important safety instructions 3 Allow at angle of air around the projector.
- Locations near the projector.
-
Doing so may contaminate optical components, shortening the projector's life...
User Manual - Page 10
... on the projector or place 13. Do not block the projection lens with any objects upon it is under operation as this could cause the objects to become wet, disconnect it to have the projector serviced.
4 Important safety instructions Safety Instructions (Continued)
10.
To temporarily turn off the lamp, press Blank on the projector or remote...
User Manual - Page 11
...Multi-language on the ambient lighting conditions, selected input source contrast/brightness settings, and is normal and expected behavior. Introduction
Projector features
The projector integrates high-performance optical ... Switchable normal and Economic modes to reduce the power consumption • Built-in speaker provides mixed mono audio when an audio input is connected • Powerful AV ...
User Manual - Page 12
...Power cord
Cleaning cloth
4. Component Video to video equipment. Carefully unpack and verify that you have all of these items are missing, please contact your region, and may differ from those illustrated. Projector... a PC and to VGA (D-sub) adaptor cable
5. Shipping contents
The projector is shipped with battery
VGA cable
USB cable
Optional accessories
1.
RS232 connector
...
User Manual - Page 14
....)
Turns the projector on page 41 for more information.)
Indicates the status of the lamp. Lights up or flashes when the projector is selected, there are several picture setup options available. 4. You can press any... signal is under operation. 9. 3 Left 10. Power indicator light (Refer to "Start up" on page 21 and "Shutdown" on page 41 for more information.)
Lights up or flashes ...
User Manual - Page 27
... a wall socket. Turn on the projector or remote control to search for information. Press and hold (for 2 seconds) the Power button on page 28 for input signals.
You can be inconvenienced if you activate the password functionality and subsequently forget the password. If the frequency/ resolution of the input signal exceeds the projector's operating range, you will...
User Manual - Page 28
...BenQ service center to cancel.
22 Operation To change number
the password.
Press Up 5 to try again or press Down 6 to decode the number. Press Auto to the
previous screen and ...menu and go to
Setting > Change Password.
2. Press Down 6 to cancel the
Password Setup Do you can retry by turning off the projector (by pressing Power) and start again, or if you forget the ...
User Manual - Page 29
... control. Fine-tuning the image size and clarity
1.
To adjust the projector:
1. The strong light from the lamp may need using the zoom ring.
Operation 23 i. Press Down 6 to cancel the set-up the projector while pressing the front adjuster button, then slowly lower the projector. The screen will be displayed at the bottom right of Frequency...
User Manual - Page 30
..., besides adjusting the height of the image. Keystone
0
Keystone
+6
24 Operation Press 3 Left/ Right 4 on the remote control or 3. Go to
Picture
--> Keystone and adjust the values by pressing Left 3/ Right 4 on the projector or
2. Press Right 4 on the projector or Left 3/ Right 4on the remote control.
Press Right4 to correct keystoning at the top of the...
User Manual - Page 32
... an image is frozen. The Power indicator light flashes orange and the lamp shuts down, the fans continue to cool down. Connect the projector to your display software program (on a connected PC) which responds to using this function.
Press Power a second time to freeze the image. Press Power and a prompt message appears. Disconnect the power cord from the wall socket...
User Manual - Page 43
... of lamp hour
When the projector is in operation, the duration (by hours) of that in normal mode. That is normally run with the Lamp indicator lighting up after turning the power back on page 41. The following Lamp warning displays will remind you may explode. The lamp has been in operation for 40 seconds. The lamp MUST be...
User Manual - Page 47
...is under normal operation. -
If you try to cool down as it will shutdown again. Light
Status & Description
Power Temp Lamp
Lamp events
O
-
-
- Please contact your dealer
for assistance.
1.
The projector is flashing during powering up. - Or
2. Please contact your dealer for assistance. The projector has shutdown automatically. The projector needs 90 seconds to...
User Manual - Page 50
... the signal cable is out of the lens using the focus ring.
Adjust the focus of power. Turn the video source on and check that it is still attached to turn the projector on the projector, and plug the power cord into the power outlet.
Attempting to the lens. Wait until the cooling down process has completed.
User Manual - Page 51
Specifications
Projector specifications
All specifications are subject to 23.5 mm 200W lamp
Electrical
Power supply Power consumption
...Operating temperature Operating relative humidity Operating altitude
0°C ~ 40°C at 0°C-23°C
Specifications 45 General
Product name Model name
Digital Projector MP610
Optical
Resolution Display system Lens F/Number Lamp
800 x 600 SVGA...
User Manual - Page 54
Important: The above warranty shall be void if the customer fails to operate the product in accordance with any warranty claim. For other... in-between 0°C and 40°C, altitude lower than 10000 feet, and avoiding to operate the projector in material and workmanship, under normal usage and storage. Warranty
Limited Warranty
BenQ warrants this product is found to be defective within...
Similar Questions
I Have A Benq Projector Mp610. I Lost My Password And Now I Cannot Use My Projec
I have a BenQ Projector MP610. I lost my password and now i cannot use my projector. I get the code:...
I have a BenQ Projector MP610. I lost my password and now i cannot use my projector. I get the code:...
(Posted by jasurbekj 10 years ago)
Replacing The Lamp In My Benq Mp 610 Dlp Projector
how can i replace the lamp inmy projector
how can i replace the lamp inmy projector
(Posted by martyahill 11 years ago)
Where Is Cmos Battery Located For Mp610 Benq Projector?
(Posted by joezira 11 years ago)
At Projector Powered(green Light) On The Start Up Logo Is Not Projected???
At power sources verified okay, lens cap removed, but at projector powered on the projector does not...
At power sources verified okay, lens cap removed, but at projector powered on the projector does not...
(Posted by pmoka 13 years ago)
Benq Mp511 Projector Model Fails. Vertical Lines Like Bars
my projector vertical lines appear glossy. svga-signal or no signal. If this is the main logic board...
my projector vertical lines appear glossy. svga-signal or no signal. If this is the main logic board...
(Posted by aislas8a 13 years ago)