ZyXEL omni.net Plus Support and Manuals
Get Help and Manuals for this ZyXEL item
This item is in your list!
View All Support Options Below
Free ZyXEL omni.net Plus manuals!
Problems with ZyXEL omni.net Plus?
Ask a Question
Free ZyXEL omni.net Plus manuals!
Problems with ZyXEL omni.net Plus?
Ask a Question
Popular ZyXEL omni.net Plus Manual Pages
Quick Start Guide - Page 3
...free disk space for the driver and software. • A computer with COM (Communication) ports.
3 Hardware Installation
3 Omni 56K Plus Modem Quick Start Guide
1 Introduction
Models included in this guide at the time of free disk space for the driver and software. • A USB-equipped computer with a functioning USB controller.
2.2 COM Plus
To install the COM Plus you will need the following...
Quick Start Guide - Page 7
... restart your computer, then plug the USB cable back in again. Plug and Play Installation Screens for Windows 2000 are similar.
7 If no installation wizard starts, you may go to the manual installation section to install your driver manually or unplug the USB cable and plug it in . Omni 56K Plus Modem Quick Start Guide
Figure 4 Rear Panel Connections
4 Software Installation
4.1 USB Plus
Follow...
Quick Start Guide - Page 9
... of your system as well as shown, click the Modems tab and the Add button.
9 Omni 56K Plus Modem Quick Start Guide 4. Windows 98 SE/Me: Select
The updated driver (Recommended) and click Next to enter Control
Panel. Click Start, select Settings to continue.
5. Manual Installation Screens for Windows 2000 are shown here. 1. Click Next to complete the...
Quick Start Guide - Page 13
... for your dial-up networking connection. Click Finish to setup your dial-up Networking
Use the connection wizard to finish
installing the software.
10. After the ZyXEL Omni 56K COM Plus modem has been installed successfully, click Finish.
5 Dial-up connection after you . Omni 56K Plus Modem Quick Start Guide 9. Windows 98SE/Me: Click Start, Programs, Accessories,
Communications...
Quick Start Guide - Page 17
... the software driver.
Check for the modem and install the driver. Connect the modem to the modem. Windows does not auto-detect the USB connection to another computer. Carefully follow the instructions to search for possible hardware conflicts. If ZyXEL OMNI 56K USB Plus is properly connected to the USB port on -screen instructions to uninstall and reinstall the software driver. Plug...
Quick Start Guide - Page 18
... wire. Carefully follow the instructions to uninstall and reinstall the software driver.
Check the telephone wire (use it to the phone jack with COM ports or try using a different RS-232 cable).
If the error persists, you should contact your computer and the modem power switch are on . If ZyXEL OMNI 56K COM Plus is receiving sufficient power...
User Guide - Page 8
... is documented in the package. This manual may also be included.
• "Enter" means for improvement to techwriters@zyxel.com.tw or send regular mail to the Omni 56K USB Plus and/or Omni 56K COM Plus modems as the Omni 56K Plus. Certifications Refer to install your purchase of networking terms and additional support documentation.
Earlier versions may refer to...
User Guide - Page 11
... port interface and the Omni 56K USB Plus uses Universal Serial Bus (USB) connection to install the modem. Support Fax class 1, class 2 and class 2.0 command set. The rate selection depends on the line quality, and server side configuration.
1.2 Main Features
ZyXEL fifth generation data pump with auto fall-forward and fall-back. Models included in this series...
User Guide - Page 17
... will start sending data again to the modem.
V.42 supports both MNP and V.42 error control protocols. The Omni 56K Plus modems support both LAPM and MNP4. A V.42 handshaking will try MNP4. Specifications and Function Description
2-5 When the modem's transmission buffer is a bi-directional flow control. On the computer software side, when the receiving buffer of the modem...
User Guide - Page 18
...), commonly called station.
If you are two kinds of phone service that supports it is about 50 % more efficient.
2.5.7 Repeat Dial
The modem will cycle dial through the four numbers stored in other is used with the phone company. Omni 56K Plus Series User's Guide
2.5.6 Data Compression
In the modem, the data compression is disabled...
User Guide - Page 22
...computer fax software of storage required. A maximum of this time limit, the line will be changed, the modem requires the supervisor password... message announcement.
2.7.1 Voice IS-101 Command Set
Please refer to the Voice command sets in Chapter 4.
2.7.2 4-bit Voice Data ...Specifications and Function Description Omni 56K Plus Series User's Guide
Before the security type or level ...
User Guide - Page 35
Omni 56K Plus Series User's Guide
COMMAND *Dn *En *Gn
*HS *Hn *In *Pn *Qn
Table 4-4 Extended AT* Command Sets
OPTIONS
FUNCTION & DESCRIPTION
REF.
*C3
8-bit character length
n=0-3
Set default dial pointer at location 'n.' S29
*D0 *
(See also S35.4 and S38.0)
Modem error control negotiation.
If call back security is disabled, the modem will disconnect the line...
User Guide - Page 40
... CSI. Report session negotiation parameters response; Receive error on phase D hang up code. Report the non-standard facilities command frame. Report the non-standard setup frame response.
4-12
Command Sets procedure interrupt requested.
Facsimile connection response. refer to +FDCC=.... Omni 56K Plus Series User's Guide
Table 4-9 Supported Commands (per TIA PN2388 8/20/90...
User Guide - Page 42
... are not reported. tpr=1:Transmitter parameters are not reported.
4-14
Command Sets nsr= 0:Non-standard frames are reported. idr=1: ID Strings are not reported. Omni 56K Plus Series User's Guide
Table 4-11 Service Class 2.0 Commands
COMMAND
DESCRIPTION Page Width
Page Length
Data Compression Format
Error Correction Binary File Transfer Minimum Scan Time/Line
+FIS=vr,br...
User Guide - Page 44
...CLASS 2.0 FAX.
8: VOICE.
Table 4-11 Service Class 2.0 Commands
DESCRIPTION Adaptive Answer Mode Phase C Timeout Minimum Phase C Speed
Buffer Size
VALUE n=0:Answers as set by +FCLASS n=1:Answers and autodetermines the call type. Model ID
N/A
Revision
N/A
Voice
N/A
recording
DEFAULT
DESCRIPTION
2
0: NO flow control.
1: (XON/XOFF) Software flow control.
2: (RTS/CTS) Hardware flow...
ZyXEL omni.net Plus Reviews
Do you have an experience with the ZyXEL omni.net Plus that you would like to share?
Earn 750 points for your review!
We have not received any reviews for ZyXEL yet.
Earn 750 points for your review!