ZyXEL XGS1910-24 Support and Manuals
Get Help and Manuals for this ZyXEL item
View All Support Options Below
Free ZyXEL XGS1910-24 manuals!
Problems with ZyXEL XGS1910-24?
Ask a Question
Free ZyXEL XGS1910-24 manuals!
Problems with ZyXEL XGS1910-24?
Ask a Question
Popular ZyXEL XGS1910-24 Manual Pages
User Guide - Page 5
... operate together with 20, 44 or 48 10/100/1000 Mbps Ethernet ports. With its built-in the stack. The Ethernet ports on the GS1910-24HP or GS1910-48HP are done on the master switch, which then maintains and manages the slave switches in web configurator, managing and configuring the Switch is easy. The XGS1910-24 or XGS1910-48 is stackable and provides two or...
User Guide - Page 15
... / SFP
10/100/1000 Mbps Dual Personality Interfaces
Console Port
RJ-45 Ethernet Ports
Figure 9 Front Panel: GS1910-24HP
10/100/1000 Mbps RJ-45 PoE Ports
10/100/1000 Mbps RJ-45 PoE / SFP Dual Personality Interfaces
Console Port
Figure 10 Front Panel: GS1910-48
10/100/1000 Mbps RJ-45 Ethernet Ports
GS1910/XGS1910 Series User's Guide
SFP Slots
15
User Guide - Page 16
Chapter 3 Hardware Overview
Figure 11 Front Panel: GS1910-48HP
10/100/1000 Mbps RJ-45 PoE Ports
Figure 12 Front Panel: XGS1910-24
SFP Slots SFP+ Slot
10/100/1000 Mbps RJ-45 Ethernet Ports
10/100/1000 Mbps RJ-45 / SFP
Dual Personality Interfaces
Console Port
Figure 13 Front Panel: XGS1910-48
SFP+ Slot
10/100/1000 Mbps...
User Guide - Page 17
... Ethernet cable.
3.1.1.1 Default Ethernet Settings
The factory default negotiation settings for future use, such as firmware upgrade using Category 5/5e/6 1000Base-T Ethernet cables. SFP+ Slots (XGS1910-24
and XGS191048 only)
Use SFP+ transceivers in these ports for fiber-optic or copper connections to 100 Mbps. The duplex mode can detect and adjust to backbone Ethernet switches. Chapter...
User Guide - Page 21
... Rear Panel: GS1910-24HP Figure 20 Front Panel: GS1910-48 Figure 21 Front Panel: GS1910-48HP Figure 22 Front Panel: XGS1910-24 Figure 23 Front Panel: XGS1910-48
Chapter 3 Hardware Overview
3.2.1 Power Connector
Make sure you are using the correct power source as shown on the power.
GS1910/XGS1910 Series User's Guide
21 Use the following procedures to connect the Switch to a power...
User Guide - Page 22
... in stacking.
The Switch is on the front panel.
The system is rebooting and performing self-diagnostic tests. The system is ...24 and
XGS1910 -48 only)
Green Amber
On On
Blinking
PWR SYS
Green Green
Off On Off Blinking
On Off
ALM
Red
On
Off
10/100/1000 Mbps RJ-45 Ports
LNK/ACT Green
Blinking
Amber
On Blinking
On
Off
PoE
Green
On
(GS1910-
24HP and GS1910...
User Guide - Page 25
... Login
1 Start your device. The recommended screen resolution is an HTML-based management interface that allows easy Switch setup and management via Internet browser. Press [ENTER]. CHAPTER 4
The Web Configurator
This section introduces the configuration and functions of the Switch (for example, the default management IP address is enabled by default in the Location or Address field.
User Guide - Page 28
... you to screens where you can configure authentication and accounting services via the Switch, configure the access control list, DHCP snooping, DHCP relay, IP source guard and ARP inspection settings.
AAA
This link takes you to a screen where you can change the system login password, manage the privilege levels for each multicast VLAN. Spanning Tree
Bridge...
User Guide - Page 29
... the Switch sets the priority level and drop eligible indicator field in the stack. Protocol-based This link takes you to a screen where you can limit the number of incoming traffic on the Switch. Port Tag Remarking
This link takes you to a screen where you can configure a Voice VLAN for traffic on the XGS1910-24 or XGS1910-48...
User Guide - Page 31
... it is not available on the XGS1910-24 or XGS1910-48. This link takes you to a screen where you can view the LLDP neighboring device information. This link takes you to a screen where you can ping IPv4 addresses to the factory defaults.
This link takes you to a screen where you can to reset the Switch back to test connections.
User Guide - Page 34
... by a DHCP server has priority over the IP address you manually configured.
6 The VLAN ID field lets you enter the ID of the VLAN group to which the Switch is connected. See Section 4.2 on page 25 for login accounts.
34
GS1910/XGS1910 Series User's Guide Click Renew to update the IP address and DNS server information after you...
User Guide - Page 44
...Switch's port on which port isolation is a port on the Switch are in a VLAN but still allow ports to the XGS1910-24 or XGS1910-48. An isolated port cannot communicate with other isolated ports even when they are in private VLAN 25 and enable port isolation to block traffic between ports. Internet
In this private VLAN.
44
GS1910/XGS1910 Series User's Guide You want to do port...
User Guide - Page 51
... changed. To configure the settings:
GS1910/XGS1910 Series User's Guide
51 Chapter 5 Tutorials
2 Configure static trunking - Packets from the same source and/or to establish trunk groups. In this group as shown in the same trunk group must connect all ports point-to-point to the same Ethernet Switch and configure the ports for LACP trunking.
•...
User Guide - Page 65
... policy you just created in the Policy ID field of your rules is , port 9 to which you want to Configuration > Security > Network > ACL > Ports. GS1910/XGS1910 Series User's Guide
65 The screens may vary slightly for different models.
9 Go to apply this example.
Chapter 5 Tutorials
8 Click Save. This tutorial uses the XGS1910-24 screens as rules are listed.
User Guide - Page 71
... access the Switch.
GS1910/XGS1910 Series User's Guide
71
See Section 5.13 on page
66. These fields are routers between your Switch. Pop-up windows and has JavaScripts and Java enabled.
4 Make sure your computer is not on.
2 If you have to reset the device to its factory defaults, and try to its factory defaults. I can see the troubleshooting suggestions for...
ZyXEL XGS1910-24 Reviews
We have not received any reviews for ZyXEL yet.