Yamaha V2.2 Support and Manuals
Get Help and Manuals for this Yamaha item
Yamaha V2.2 Videos
HONDA RUCKUS RALLY (v2.2) • Super Sunday • HMP©2009
Duration: 4:27
Total Views: 21,660
Duration: 4:27
Total Views: 21,660
Yamaha XTZ 125 Luz LEDs colin con Stop, Posicion y Giros V2/2 - www.LEDFACIL.com.ar
Duration: :43
Total Views: 5,158
Duration: :43
Total Views: 5,158
StyleMagic YA v2.2 - tutorial part 1
Duration: 11:49
Total Views: 20,917
Duration: 11:49
Total Views: 20,917
Acoustic Samples B-5 V2.2 with Yamaha AR80 Organ
Duration: 8:52
Total Views: 116
Duration: 8:52
Total Views: 116
Popular Yamaha V2.2 Manual Pages
RIVAGE PM series V2.2 Supplemental Manual EN - Page 2
Contents
Supporting a new HY144-D-SRC card 3 Supporting a new HY128-MD card 4 MIX SEND COPY 6 Additional option during loading 7 Displaying a patch conflict between DSP engines 8 Expanded SENDS ON FADER mode function 10 Additional CUE monitor sources 10 Mirroring Operation Check function 11
CONTENTS
2
RIVAGE PM series V2.2 Supplemental Manual
RIVAGE PM series V2.2 Supplemental Manual EN - Page 3
... Firmware Update Guide". Supporting a new HY144-D-SRC card
Supporting a new HY144-D-SRC card
This new digital I/O card supports ...Firmware Update Manager. If the Dante network is generated based on the PTP master clock on the Dante network.
3
RIVAGE PM series V2.2 Supplemental Manual...installed, use Dante Controller to check the "Enable Sync to the network. CONTENTS
If you plan to set...
RIVAGE PM series V2.2 Supplemental Manual EN - Page 4
SYSTEM CONFIG popup window
• MODE 2 Redundancy is maintained by using either two sets of optical or two sets of fiber optic and coaxial connectors, supporting redundant connection. If MODE 2 is inserted into the HY slot on a DSP engine. ....
• PRI2 If MODE 1 is selected, signals at OPTICAL 1 and OPTICAL 2 have priority.
4
RIVAGE PM series V2.2 Supplemental Manual
RIVAGE PM series V2.2 Supplemental Manual EN - Page 5
...; 4Fs 176.4 kHz/192 kHz, up . OUTPUT FRAME buttons Enable you to select whether the MADI input signal will be output.
5
RIVAGE PM series V2.2 Supplemental Manual
Supporting a new HY128-MD card
SPLIT button Specifies whether or not the input signal should be output.
OUTPUT CHANNEL FORMAT buttons Enable you to select the...
RIVAGE PM series V2.2 Supplemental Manual EN - Page 6
... the switch 1 is set to ON (default setting), you to the "HY128-MD Owner's Manual."
MIX SEND COPY
■ About the SOFT CTRL (software control) switches on the card. If the switch 1 is selected: Pre/Post Pre Point Post Point Level Pan On Follow On Follow Fader Follow DCA
6
RIVAGE PM series V2.2 Supplemental Manual
RIVAGE PM series V2.2 Supplemental Manual EN - Page 7
... paste destination use a different type of the entire system would be reconfigured based on the DANTE SETUP popup window settings on to use the Dante settings included in a file without any save options.
7
RIVAGE PM series V2.2 Supplemental Manual NOTE
• The Dante Controller ID will be loaded. For example, if the ID was changed...
RIVAGE PM series V2.2 Supplemental Manual EN - Page 8
... button on the TWINLANe network, the output port will be "stolen" by the DSP engine that is turned on.
STEAL button
8
RIVAGE PM series V2.2 Supplemental Manual In this case, the above-mentioned messages will be "stolen" by the second DSP engine. Meanwhile, a message will appear on the control surface that was...
RIVAGE PM series V2.2 Supplemental Manual EN - Page 9
...are being patched (Used) from another DSP engine or device. This channel is not currently patched to the setting on the card. Alternatively, the port may inadvertently remove other patches that are not assigned to that port ... ports is limited due to an Output Port."
9
RIVAGE PM series V2.2 Supplemental Manual To make it active, you must remove the patch, and then make the patch again.
RIVAGE PM series V2.2 Supplemental Manual EN - Page 10
...source, we recommend that you turn off the CUE INTERRUPT button so that has its CONSOLE ID set to "2".) In this way, you can now adjust the send levels without opening the SENDS ON...will not be assigned to a USER DEFINED key.
10
RIVAGE PM series V2.2 Supplemental Manual The new CUE INTERRUPT button for the PHONES settings now enables you switched the master bus.
NOTE If CUE is a ...
RIVAGE PM series V2.2 Supplemental Manual EN - Page 11
...'s Unit ID does not support the Mirroring Check function, "Mirr Chk" will automatically be lost unless you save the data first.
11
RIVAGE PM series V2.2 Supplemental Manual When "DONE" appears, you can check the operation while two DSP engines are set as the word clock master...for failed DSP A, DSP B will remain active unless you change the active DSP from the panel of system setup.
Yamaha V2.2 Reviews
We have not received any reviews for Yamaha yet.