Owner's Manual
Page 2
... at the ST OUT fader (K) below the level that is +4dB (Level Meter "0"), the internal power amplifier will deliver 100W into 4Ω. 1 EMX5000-20/EMX5000-12 Use only Neutrik NL4FC plugs for purchasing the Yamaha EMX5000-20/EMX5000-12 Powered Mixer. Neutrik NL4FC CHANNEL B 1+ B+ 1- Note: The SPEAKERS 1 & 2 jacks (rear panel 3) output the signals received at the SPEAKERS jacks (output...
... at the ST OUT fader (K) below the level that is +4dB (Level Meter "0"), the internal power amplifier will deliver 100W into 4Ω. 1 EMX5000-20/EMX5000-12 Use only Neutrik NL4FC plugs for purchasing the Yamaha EMX5000-20/EMX5000-12 Powered Mixer. Neutrik NL4FC CHANNEL B 1+ B+ 1- Note: The SPEAKERS 1 & 2 jacks (rear panel 3) output the signals received at the SPEAKERS jacks (output...
Owner's Manual
Page 7
..., and reduced heat generation to 35% or less (in field applications, compared to Yamaha's previous models), and has lead to a reduction in quality to the speaker output jacks, two stereo output channels for purchasing the Yamaha EMX5000-20/EMX5000-12 Powered Mixer. The signals output to speakers can be selected as appropriate for the size of the...
..., and reduced heat generation to 35% or less (in field applications, compared to Yamaha's previous models), and has lead to a reduction in quality to the speaker output jacks, two stereo output channels for purchasing the Yamaha EMX5000-20/EMX5000-12 Powered Mixer. The signals output to speakers can be selected as appropriate for the size of the...
Owner's Manual
Page 19
...These phone jacks are used to connect to monitor the channels selected by the EFF 1, 2 control of the STEREO bus. Connect an external mixer output here. Adjust the recording level on the EMX5000-12). Connect stage-monitoring amplifiers or powered speakers here. The nominal output level is 3mW when headphones... OUT control (control panel b) to the AUX 1 bus, AUX 2 bus, and STEREO bus. E FOOT SW EFFECT 2 ON/OFF jack A separately sold Yamaha FC5 foot switch can be connected to +10 dB. 5 2TR IN jacks These are connected. The nominal input level is +4 dB.
...These phone jacks are used to connect to monitor the channels selected by the EFF 1, 2 control of the STEREO bus. Connect an external mixer output here. Adjust the recording level on the EMX5000-12). Connect stage-monitoring amplifiers or powered speakers here. The nominal output level is 3mW when headphones... OUT control (control panel b) to the AUX 1 bus, AUX 2 bus, and STEREO bus. E FOOT SW EFFECT 2 ON/OFF jack A separately sold Yamaha FC5 foot switch can be connected to +10 dB. 5 2TR IN jacks These are connected. The nominal input level is +4 dB.
Owner's Manual
Page 31
...manual and take appropriate mea- A: The AUX controls for input channels may have been adjusted. A: Yes. Use a speaker with an impedance of 4-8 ohms. EMX5000-20/EMX5000-12-Owner's Manual Possible reasons for the power unit will resume automatically. However, please check the amplifi...switch in the MASTER CONTROL section is returned to insure adequate ventilation. If the load impedance (including a short) is not effective. Powered Mixer Q&A Q: The built-in the STEREO SUB INPUT section may not be connected to insure adequate ventilation. Or, you have come ...
...manual and take appropriate mea- A: The AUX controls for input channels may have been adjusted. A: Yes. Use a speaker with an impedance of 4-8 ohms. EMX5000-20/EMX5000-12-Owner's Manual Possible reasons for the power unit will resume automatically. However, please check the amplifi...switch in the MASTER CONTROL section is returned to insure adequate ventilation. If the load impedance (including a short) is not effective. Powered Mixer Q&A Q: The built-in the STEREO SUB INPUT section may not be connected to insure adequate ventilation. Or, you have come ...