Whirlpool WMH76719CZ Support and Manuals
Get Help and Manuals for this Whirlpool item
View All Support Options Below
Free Whirlpool WMH76719CZ manuals!
Problems with Whirlpool WMH76719CZ?
Ask a Question
Free Whirlpool WMH76719CZ manuals!
Problems with Whirlpool WMH76719CZ?
Ask a Question
Popular Whirlpool WMH76719CZ Manual Pages
Installation Guide - Page 1
... important safety messages in this manual and on your particular model may differ slightly from the illustration in Rear Wall 7 Attach Mounting Plate to Wall 8 Prepare Upper Cabinet 8 Install Damper Assembly 9 Install the Microwave Oven 9 Complete Installation 10 VENTING DESIGN SPECIFICATIONS 11 ASSISTANCE 12 Replacement Parts 12 Accessories 12
MICROWAVE HOOD COMBINATION SAFETY
Your...
Installation Guide - Page 2
... User Instructions.)
NOTE: Depending on model, aluminum grease filter and charcoal filter may not be installed. Remove Cardboard Template
The cardboard piece from the
rest of the cardboard packaging. 2. Cut along the perforation to use as a rear wall template. 1. Set the cardboard template to the side and refer to withstand the heat produced by the microwave oven...
Installation Guide - Page 3
... prong. Do not use an extension cord. GROUNDING INSTRUCTIONS
■ For all governing codes and ordinances. If the power supply cord is typical for the electric current. Grounded 3 prong outlet
*30" (76.2 cm) is too short, have a qualified electrician or serviceman install an outlet near the microwave oven. Product Dimensions
17¹⁄₈"
(43...
Installation Guide - Page 4
... the damper assembly in case the venting method is changed, or the microwave oven is attached to back of the microwave oven and lift up. Keep damper plate and screws together and set aside.
4 INSTALLATION INSTRUCTIONS
Remove Mounting Plate
Depending on your model, the mounting plate may be in another location where wall or roof venting may be...
Installation Guide - Page 5
...blower motor face back of the microwave oven (as shown), performance will be reattached to back of microwave oven with flat sides facing the back of microwave oven. Damper vent covers
7.
Reattach blower motor to the microwave oven.
7. Reattach damper plate. Diagonal wire cutting pliers B. Repeat Step 2 from "Wall Venting Installation Only." Make sure damper plate tabs...
Installation Guide - Page 6
...each stud center. End holes (on mounting plate) B. Holes for lag screws E. Cabinet opening , do not install the microwave oven.
1. See illustrations in "Possible Wall Stud Configurations." See illustrations in "Possible Wall Stud Configurations."
2. Support tabs F. Wall Stud at One End Hole Figure 3
Wall Studs at End Holes Figure 2
B
C
C
C
D
B
D
A
A
A
A
E
E
E
E
F
F
NOTE...
Installation Guide - Page 7
... the marks made in Step 3 of "Mark Rear Wall."
7 Set the mounting plate aside.
Front edge of the cardboard template. These ...installation configurations. Cardboard template C. Drill Holes in place, find and clearly mark the vertical
centerline of the opening.
With the support...Mark Rear Wall." Mark Rear Wall
The microwave oven must be installed on both sides of the centerline, ...
Installation Guide - Page 8
...Installation for Wall Stud at One End Hole" in the "Drill Holes in the top of the microwave oven. NOTES: ■ If the upper cabinet has a frame around it is maintained. The template has trim lines to use as guides.
■ If the wall behind the microwave oven... plate C. Start a toggle nut on the rear wall.
With the support tabs of the mounting plate facing forward,
insert 3/16-24 x 2"...
Installation Guide - Page 9
B
A
Install the Microwave Oven
WARNING
Excessive Weight Hazard Use two or more people, lift microwave oven and hang it on support tabs at the circular shaded area "G" on Upper Cabinet Template.
8.
Cut 3/4" (19 mm) hole at the top, and the damper blade opens away from the microwave oven.
Position the damper assembly on the back of mounting plate. A. Damper...
Installation Guide - Page 10
...A
2. Bolts
For Roof Venting Installation Only
1.
Damper plate
Electrical Shock Hazard
Plug into grounded 3 prong outlet. 3.
Replace the fuse or reset the circuit breaker.
Vent B.
Damper assembly C. Do not remove ground prong. Failure to the User Instructions for troubleshooting information. Reconnect power. 4. If the microwave oven does not operate: ■ Check...
Installation Guide - Page 11
... cap E. 3¹⁄₄" x 10" to 6" (8.3 x 25.4 cm to 15.2 cm)
rectangular to vent air outside, unless using recirculation installation. Vent extension piece, at least 3" (7.6 cm) of clearance between the top of the microwave oven and the transition piece. Wall cap: 3¹⁄₄" x 10" = 40 ft (8.3 x 25.4 cm = 12.2 m) F. 45° elbow...
Installation Guide - Page 12
... need additional assistance, call us at our toll free number listed in the User Guide. To calculate the length of the installation hardware needs to use no more than three 90° elbows.
Replacement Parts
If any of the system you need the microwave oven model number and serial number. Two 90° elbows = 20 ft (6.1 m) B. 1 wall cap...
Dimension Guide - Page 1
... instructions. or 20-amp electrical supply
with a fuse or circuit breaker.
A. 2" x 4" (5.1 x 10.2 cm) wall stud B. Grounded 3 prong outlet
*30" (76.2 cm) is typical for 66" (167.6 cm) installation height.
Recommended: • A time-delay fuse or time-delay circuit breaker. • A separate circuit serving only this microwave oven. Microwave Hood Combination
PRODUCT MODEL...
Dimension Guide - Page 2
... and specifications Installation Instructions packed with...installed to change without notice. Page 2 of 2
Because Whirlpool Corporation policy includes a continuous commitment to Round Transition:
NOTE: The minimum 3" (7.6 cm) clearance must not exceed the equivalent of 140 ft (42.7 m) for either type of the microwave oven and the
. A
B
C
D
E
3" (7.6 cm)
F
27" (68.6 cm) models...
Whirlpool WMH76719CZ Reviews
We have not received any reviews for Whirlpool yet.