Whirlpool WGD8500DR Support and Manuals
Get Help and Manuals for this Whirlpool item
View All Support Options Below
Free Whirlpool WGD8500DR manuals!
Problems with Whirlpool WGD8500DR?
Ask a Question
Free Whirlpool WGD8500DR manuals!
Problems with Whirlpool WGD8500DR?
Ask a Question
Popular Whirlpool WGD8500DR Manual Pages
Warranty Information - Page 1
... was purchased. This warranty gives you specific legal rights, and you .
PROOF OF PURCHASE IS REQUIRED TO OBTAIN WARRANTY SERVICE. Please take a few minutes to review the Troubleshooting or Problem Solver section of the Use and Care Guide, scan the QR code on the duration of implied warranties of repair or replacement under this major appliance, you should...
Use & Care Guide - Page 6
...service voltage less than 240. This option is reached. You may adjust the signal to low, medium, high, or off the tones that sound when a feature, setting, or option is selected as a reminder to manually reposition bulky loads midway through the cycle. EcoBoost™ option will default on some models...available on number of items.
Cycle Guide -
The Damp Beep signal is ...
Use & Care Guide - Page 11
... you will shut off. See "Cycle Guide" for detailed information.
The default temperature may select the + Steam setting to add a short steam cycle after cycle has completed to dry. You may be changed by touching that have been made. You may adjust different settings, depending on some models): Select Steam Refresh to increase or...
Use & Care Guide - Page 12
...your model and serial number and the purchase date. be adjusted to adapt to different installations, ...environmental conditions, or personal preference. NOTE: Check the lint screen and remove any packing material before use with the Manual...settings: NOTE: The settings cannot be used with the holes in standby mode (power is intended for use .
Rest the rear support...
Installation Guide - Page 5
...parts. Contact your "Use and Care Guide." See "Venting Requirements."
■■ A separate 15 or 20-amp circuit needed for gas dryers and 30-amp circuit needed : (Not supplied with maximum slope of installation and servicing...Some codes limit, or do not permit, installation of the dryer in longer drying times.
Check existing electrical supply and venting. Space must support ...
Installation Guide - Page 21
... sure the water faucets are now installed. If dryer will go back through steps to control the buildup of its first cycle. q Wipe dryer drum interior thoroughly with your dryer vent may be a problem with a damp cloth to the need for certain part replacement or repair.
q Check for leaks. All Models:
q Select a Timed Dry heated cycle...
W10240504 - Page 8
...update for Status_Airflow
Heater On/Off
is present, it also displays when
the Status_Airflow = 2.
7
Service...Steam Models Only:...SERVICE TEST MODE CHART (continued)
Step #
Action
Component
User Interface Response
6
Load Mass for 5 seconds to jump to the water system test. Airflow Display
Value
0 1 2 3 (Default)
Setting...
W10240504 - Page 10
...Interface (UI) Stuck Button
Indicates a stuck button (depressed for the dryer model displaying the fault/error code. This fault code will only appear when in the service diagnostic mode. See TEST #6: Buttons and Indicators, page 22. F2E4 UI Software Error: Incompatible Parameter File
Replace the User Interface.
F3E1 Exhaust Thermistor Open/Shorted
Indicates that does...
W10240504 - Page 11
... #4a: Thermistors, page 18.
See Test #1: ACU Power Check, page 12. Dryness or Dry Level setting for L1 and L2. Clean if necessary.
See Test #5a: Adjusting Customer-Focused Dryness Level, page 21.
FOR SERVICE TECHNICIAN'S USE ONLY
TROUBLESHOOTING GUIDE
PROBLEM
POSSIBLE CAUSE
CHECKS & TESTS
WILL NOT POWER UP - See Test #2: Supply Connections, page 13...
W10240504 - Page 12
...SERVICE TECHNICIAN'S USE ONLY
TROUBLESHOOTING...5. ACU Connectors & Pinouts
PAGE 12
DO NOT REMOVE OR DESTROY With voltmeter set to DC, unplug connector P2 from the ACU and connect black probe to... THERMISTOR INLET THERMISTOR INLET THERMISTOR
P14-6 R/W OUTLET THERMISTOR P14-5 BLK MODEL RTN (GAS MODEL) P14-4 BLK MODEL (GAS MODEL)
P9 Heater Relay
Motor Relay
P13
L1 - WATER VALVE/DOOR SWITCH...
W10240504 - Page 16
...parts and panels. 14. Perform steps under "Service Test Mode", page 6, to step 13. If the motor has two capacitors attached as shown in the table above, replace... motor capacitors: each . For gas models, check for the run capacitor inductance ...problem; The capacitor
26 4 3 5 1
TEST #4: Heat System
This test is still an open circuit, check and repair the main wiring harness.
12. FOR SERVICE...
W10240504 - Page 19
...setting, retest at a different temperature setting.
5. If either pin indicates continuity to access the machine electronics.
3. If no error code is displayed and the connections to detect air flow, and assists in question, using the Timed Dry cycle. Remove load from dryer and disconnect external vent.
2. If the preceding steps did not correct the problem, replace...part ...FOR SERVICE TECHNICIAN...
W10240504 - Page 23
... replace the water valve. If an open circuit is connected to step 5.
If not, repair or replace ...937; (±5%), go to step 7. 7. Reassemble all parts and panels. Inside the drum, unscrew the water nozzle... on some models)
Activate Service Test Mode (see wiring diagrams,... problem, replace the ACU.
Water System Components. 5. Inside the drum, unscrew and replace...
Ventilation Specification - Page 4
... each individual dryer exhaust duct. NOTE: This guide is removed from accumulating in compliance:
1. National Fuel Gas Code.
3.
Proper venting of the building. WARNING...) exhaust duct connections. International Mechanical Code: 2009 version, sections 504 and 913.
2. Gas Clothes Dryers.
5. See the Installation Instructions for the specific dryer model being used for balancing out the...
Ventilation Specification - Page 5
...rated vent length is at connection to dryer (no heat).
Codes Agency Approvals
All Whirlpool electric dryer models, including "long vent dryers," Turbo Vent™ dryers and...curved portions of elbows for each model, or on or adjacent to reduce noise transfer.
5
A.
For single dryer venting systems, see the Installation Instructions for the specific dryer model being used . (The total ...
Whirlpool WGD8500DR Reviews
We have not received any reviews for Whirlpool yet.