Whirlpool WGD70HEB Support and Manuals
Get Help and Manuals for this Whirlpool item
View All Support Options Below
Free Whirlpool WGD70HEB manuals!
Problems with Whirlpool WGD70HEB?
Ask a Question
Free Whirlpool WGD70HEB manuals!
Problems with Whirlpool WGD70HEB?
Ask a Question
Popular Whirlpool WGD70HEB Manual Pages
Installation Instructions - Page 4
...-joint compound resistant to LP gas
4 Check that opens to your Use and Care Guide for information about accessories available for your installation. Check local codes. Check existing electrical supply and venting. Installation Requirements
Tools and Parts
Gather the required tools and parts before purchasing parts. Optional Equipment: (Not supplied with dryer) Refer to
(new vent...
Installation Instructions - Page 5
...install Extended Dryer Feet Kit, Part Number 279810. If not level, clothes may not tumble properly and automatic sensor cycles may not operate correctly.
■■For garage installation, place dryer at temperatures below 40° F (4° C). measurement
NOTE: Most installations... dryer must support dryer weight of...(159 mm)
Vent
Water inlet
(Steam Models Only)
297/8"* (759 mm)
31/2"*...
Installation Instructions - Page 6
...plugged into dryer. Some codes limit, or do not permit, installation of installation and servicing; NOTE: No other...: ■■Mobile Home Installation Hold-down Kit Part Number 346764
is adequate and ... (such as a nearby window) should be obtained from
your Use and Care Guide. For mobile home installation of the door are required. Canada Only
ELECTRICAL REQUIREMENTS
18" min. (457 ...
Installation Instructions - Page 7
... appropriate outlet that you use Power Supply Cord Replacement Part Number 8529008.
WARNING: Improper connection of the equipment-
A time-delay fuse or circuit breaker is properly grounded.
If using a replacement power supply cord, it is recommended that is properly installed and grounded in accordance with all local codes and ordinances. The plug must be grounded...
Installation Instructions - Page 8
..., depending on the model/serial number plate is recommended that resist the action of your dryer to the rigid gas supply line. Gas shut-off valve must be installed within six (6) ft. (1.8 m) of E.I. If the total length of the dryer in elevation.
NOTE: Pipe-joint compounds that an individual manual shut-off valve...
Installation Instructions - Page 9
... pipe-joint compound resistant to action of all connections by hand - valve is open when handle is shown. Bubbles will show a leak. Install Leveling Legs
Make Gas Connection (Gas Models Only)
1. Prepare dryer for leveling legs
To avoid damaging floor, use a large flat piece of dryer. Screw in supply line; use TEFLON...
Installation Instructions - Page 10
...building. Do not use plastic or metal foil vent.
Replace plastic or metal foil vents with lint. Flexible metal vent: (Acceptable...)
■■ Must be fully extended and supported in final dryer location.
■■ Remove...result in reduced airflow and poor performance.
■■ Do not install in enclosed walls, ceilings, or floors.
■■ The total...codes and ordinances.
Installation Instructions - Page 12
... of hose failure. Example: A gas model would be connected to secure vent, because they can catch lint.
Install Vent System
1.
NOTE: Replace inlet hoses after 5 years of use to...model has a long vent system, refer to exhaust hood with new rubber washer. 12 Install exhaust hood
12" min. (305 mm)
12" min. (305 mm)
Install exhaust hood and use old hoses. Secure vent to the type code...
Installation Instructions - Page 15
... part replacement or repair.... instructions are now installed.
Electric Models...
q Plug into a grounded outlet.
NOTE: You may lead to the need for leaks. Be sure vent is first used. Reinstall the 4 screws in the dryer. If there is
recommended to control the buildup of your Use and Care Guide.
Do not select Air Only Temperature setting...
Installation Instructions - Page 16
... A
Fig. Then lift out the outer window and retainer up .
Lift off the trim ring and set aside.
16 Position the door with arrows in the figure A above. Using a Phillips screwdriver, remove ...securing the door strike to the door frame of the door facing up and off the inner door and set aside (B). B
Using a Phillips screwdriver, remove the 2 screws from the outer window retainer and rotate ...
Installation Instructions - Page 19
...
Position the door with the inside of the door facing up and out to the dryer and lift up . Lift off the inner door and set aside.
4. Reverse door swing round-shaped door - Place the door on a soft towel or other non-scratch surface.
Remove inner door from outer door
IMPORTANT...
Installation Instructions - Page 20
... 3 TORX® screws removed earlier and the hinge assembly with the 4 T25® screws removed earlier. Remove door from which they were removed.
6. Retain or set aside the 4 screws.
20 Reinstall the 10 screws securing the inner door to remove the door.
Reverse door swing square-shaped door
1. Reinstall inner door...
Installation Instructions - Page 21
...screws securing the door strike to release the tab. Remove the 4 screws above and below the door strike and set aside. NOTE: There is a small release tab on the opposite sides from outer door
Release tab
Hinge
Using ...176; and attach to the outer door. Lift off the inner door and set aside for later use. Using a Phillips screwdriver, remove the 13 screws securing the inner door to the ...
Dimension Guide - Page 1
...installation and servicing. ■■ Additional clearances might be required for exhaust vent with a door, minimum ventilation openings in the top and bottom of the dryer to reduce noise transfer. ■■ For closet installation...W10573707D 03/2016 measurement
Recommended installation clearances (dryer only):
53/4"* (146 mm)
Vent
Water inlet
(Steam Models Only)
Gas
297/8"* (759...
Dimension Guide - Page 2
...For complete details, see Installation Instructions packed with the National Fuel Gas Code ANSI Z223.1. gas ...manual shutoff valve must be connected to the cold water faucet using elbows or making turns, allow as much
room as possible. ■■ Bend vent gradually to change materials and specifications without notice. WATER (STEAM MODELS ONLY) REQUIREMENTS
The dryer must be installed...
Whirlpool WGD70HEB Reviews
We have not received any reviews for Whirlpool yet.