Whirlpool WGD5810BW Support and Manuals
Get Help and Manuals for this Whirlpool item
This item is in your list!
View All Support Options Below
Free Whirlpool WGD5810BW manuals!
Problems with Whirlpool WGD5810BW?
Ask a Question
Free Whirlpool WGD5810BW manuals!
Problems with Whirlpool WGD5810BW?
Ask a Question
Popular Whirlpool WGD5810BW Manual Pages
Installation Guide - Page 5
... sensor cycles may not operate correctly.
Check code requirements. See "Venting Requirements."
29" Wide Models Dryer Dimensions
29" (737 mm)
29" (737 mm)
Installation Spacing
18"* (457 mm)
14" max...dryers.
■■ A separate 15 or 20 amp circuit for the exhaust vent with elbow.
Most installations require a minimum 5½" (140 mm) clearance behind the dryer for gas dryers...
Installation Guide - Page 7
.... For ordering information, please reference the "Use and Care Guide."
7 Install Leveling Legs
GAS DRYER POWER HOOKUP
Gas Supply Requirements
1. Prepare dryer for use with Natural Gas. capacity washer) from dryer carton; Slide the dryer until bottom of foot is located on the model/serial rating plate for the type of 3.6 cu. Leave enough room for electrical connection and to...
Installation Guide - Page 8
... your gas dryer can be easy to reach for opening and closing.
This dryer must be installed in accordance with the National Fuel Gas Code, ANSI Z223.1. Use an elbow and a 3/8" flare x 3/8" NPT adapter fitting between dryer pipe
and 3/8" approved tubing. ■■ Lengths over 20 ft. (6.1 m) should be connected to the gas supply. rating indicated on the model...
Installation Guide - Page 9
... not plugged with rigid metal or flexible metal vents.
The plug must not be fully extended and supported in final dryer location. ■■ Remove excess to follow these instructions can result in death, fire, or electrical shock.
■■ 120 Volt, 60 Hz., AC only, 15- Do not modify the plug provided...
Installation Guide - Page 12
...dryer location using straightest path possible. NOTE: For LP gas connections, you must use caulking compound to existing gas...gas. Dupont De Nemours and Company. Install exhaust hood
12" min. (305 mm)
Make Gas Connection
1. Plan pipe fitting connection
D
12" min. (305 mm)
Install...ft. (21.3 m)
Install Vent System
1. Use clamps to dryer. Using a wrench to tighten, connect gas supply to seal all...
Installation Guide - Page 13
... front to see what was skipped. After dryer is level. Move dryer to final location
Move dryer to exhaust outlet
2. Level dryer
Check levelness of your "Use and Care Guide."
q Check that you have all four legs are now installed.
Avoid crushing or kinking vent. q Check dryer's final location.
Dryer vent must be level for 5 minutes, open it...
Warranty Information - Page 1
... Proof of original purchase date is required to Whirlpool within 30 days from the date of purchase.
6. Repairs to parts or systems resulting from unauthorized modifications made to published user or operator instructions and/or installation instructions.
2.
Service calls to correct the installation of your major appliance, to replace or repair house fuses, or to correct house wiring...
Dimension Guide - Page 1
...1½" (38 mm) (to match height of 3.8 cu. ft. Wide opening hamper door
Installation Spacing
18"* (457 mm)
14" max.*
(356 mm)
48 in.2* (310 cm )2...
*Required spacing
A
B
A. Gas Dryer
PRODUCT MODEL NUMBERS WGD4800B, WGD4810B, WGD4850B, WGD4890B, WGD5500B, WGD5800B, WGD5810B
29" Wide Models Dryer Dimensions
29" (737 mm)
29" (737 mm)
27" Wide Models Dryer Dimensions
27" (686 mm)
433...
Dimension Guide - Page 2
... should be considered for ease of installation and servicing.
■■ Additional clearances might be large enough to allow the dryer door to open fully. Louvered doors with elbow. INSTALLATION REQUIREMENTS
GAS SUPPLY REQUIREMENTS
Gas supply: This dryer is recommended to the action of L.P. Dryer can be converted to the gas supplier and local codes, 3/8" approved tubing may be used...
Use & Care Guide - Page 5
... to help keep wrinkles from the dryer as soon as it .
4 OPTIONS AND SETTINGS TEMP (for use with Manual Cycles only) Select a drying temperature based on some models)
DRYNESS LEVEL (for use with... and fluffs the load to select a cycle for detailed descriptions of a cycle. See "Cycle Guide" for your estimated energy usage based on the Sensor Cycles.
When pressed during a cycle or ...
Use & Care Guide - Page 6
... interrupt.
MANUAL CYCLES
Not all cycles and settings are unsure...setting may be selected on all models. If you are available on model, temperature may be used for items that cycle. SENSOR CYCLES - to the care label directions.
6
For best results,
run the dryer for a load, select the lower setting rather than the higher setting.
This cycle is desired. CYCLE GUIDE...
Use & Care Guide - Page 8
...The default cycle settings will change by pressing the button for Manual Cycles only. Select...setting.
See the "Cycle Guide" or the display for sensor drying. NOTE: Not all options and settings...settings are unable to remove the load promptly, press the Wrinkle Shield button to turn ON or OFF at the end of a cycle. For some models)
Select Drum Light to turn ON or OFF at which the dryer...
Use & Care Guide - Page 10
Gas models only: Disconnect gas supply line pipe and
remove fittings attached to secure dryer door. Replace the bulb with the screw.
4. Disconnect power. 2. Use tape to dryer pipe. 4. Reinstalling the Dryer
Follow the "Installation Instructions" to secure dryer door. There are 3 drying settings, which are displayed using your dryer only when you are secure in gas supply line....
Use & Care Guide - Page 11
... a room with lint, restricting air movement.
See "Installation Instructions." If the problem continues, call an electrician.
Wrong type of dryer cycles requires temperatures above 45ºF (7ºC). Clean out pockets before each load. Household fuse is a gas dryer. Separate the load items and restart the dryer. If the problem continues, call an electrician.
Hold your hand...
Use & Care Guide - Page 12
...dryer.
Add dryer fabric softener sheets at www.whirlpool.com/product_help In Canada www.whirlpool.ca for the first time. Fabric softener sheets added to garment care label instructions...for service.
Alternating between F# and E#, the dryer control has detected a problem that can stain your dryer is located. Select Touch Up Cycle to possibly avoid a service call. TROUBLESHOOTING ...
Whirlpool WGD5810BW Reviews
Do you have an experience with the Whirlpool WGD5810BW that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Whirlpool yet.
Earn 750 points for your review!