Whirlpool WGD4910XQ Support and Manuals
Get Help and Manuals for this Whirlpool item
View All Support Options Below
Free Whirlpool WGD4910XQ manuals!
Problems with Whirlpool WGD4910XQ?
Ask a Question
Free Whirlpool WGD4910XQ manuals!
Problems with Whirlpool WGD4910XQ?
Ask a Question
Most Recent Whirlpool WGD4910XQ Questions
Popular Whirlpool WGD4910XQ Manual Pages
Owners Manual - Page 5
... your load. Turn the END OF CYCLE SIGNAL knob to start the dryer. Appearance may choose a setting based on some models) is not available on ACCUDRY™ cycles.
3 WRINKLE SHIELD™ Feature (on the fabrics in your load. See "Cycle Guide" for your dryer.
Turn the WRINKLE SHIELD™ knob to 40 minutes of heat...
Owners Manual - Page 6
...-sensitive fabrics.
TIMED DRY CYCLES
Not all models. Will run the dryer for the specified time on all cycles and settings are default settings for that do not seem as dry as... a drying temperature based on all cycles and settings are unsure of Cycle Signal Temperature Fabric
Automatic cycles give the best drying in the dryer too long. CYCLE GUIDE - ACCUDRY™ -
NOTE: If you ...
Owners Manual - Page 8
... are unable to complete drying.
4. See the Cycle Guide for your load, by turning the knob to select ON or OFF at which the dryer will sound every 5 minutes until the clothes are available with all options and settings are removed, or the Wrinkle Shield™ setting ends.
6. Press PUSH to START to begin...
Owners Manual - Page 11
... movement. Make sure vent is closed completely. Make sure the dryer door is not crushed or kinked. Wrong type of the dryer? Check the front and rear edges of garments being dried.
See "Installation Instructions".
Unusual sounds
Dryer had a period of a service call...In U.S.A.
http://www.whirlpool.com/help - Has the Air Only cycle been selected. Use...
Owners Manual - Page 12
... used or was TEMPERATURE/Fabric control set to handle. Add dryer fabric softener sheets at the end of the cycle.
Allow Cool Down cycle to possibly avoid the cost of the cycle. This reduces overdrying.
12 TROUBLESHOOTING cont. http://www.whirlpool.com/help -
Drum stains are gone from dryer.
If so, ventilate the area. Load...
Owners Manual - Page 13
... must be repaired in accordance with Whirlpool's published installation instructions.
10. The removal and reinstallation of your major appliance if it . This warranty gives you specific legal rights, and you ever need it is installed in an inaccessible location or is not installed in your home.
7.
Consumable parts are unable to resolve the
problem after checking "Troubleshooting...
Warranty - Page 1
... your major appliance, to instruct you need repair service, first see the "Troubleshooting" section of the Use & Care Guide. You will pay for other rights that have been removed, altered, or cannot be provided by Whirlpool.
5. In Canada, call 1800253-1301. Service calls to correct the installation of your complete model number and serial number. This...
Ventilation Specification - Page 4
...exhaust duct.
Maximum exhaust temperature of the dryer will be reviewed to ensure dryer vent systems are other codes requiring dryers to be exhausted when installed in confined spaces where specified clearances from accumulating in the laundry area. To remove excess heat from the drum. See the Installation Instructions for the specific dryer model being used for balancing out the overall...
Ventilation Specification - Page 5
... that are sold in which the Installation Instructions do not address the vent length for the specific number of elbows for minimum clearances between the product and the enclosure surfaces.
of the exhaust vent. Codes Agency Approvals
All Whirlpool electric dryer models, including "long vent dryers," Turbo Vent™ dryers and combo washer/dryer units that have an inlet and...
Dimensions - Page 1
29" and 27" Dryers Gas (U.S.A. and Canada)
PRODUCT MODEL NUMBERS
WGD4700Y, WGD4750X, WGD4800X, WGD4850X, WGD4890X, WGD4900X, WGD4910X,WGD5100V, WGD5200V, WGD5300V, WGD5500X, WGD5510V, WGD5550X, WGD5600X, WGD5610X, WGD5700A, WGD5700V, WGD5700X
Installation clearances: The location must be required for the exhaust vent with vents
*Required spacing
3"* (76 mm)
3"* (76 mm)
1" (25 mm)
24 in2...
Dimensions - Page 2
... add one 90º turn inside the dryer. For complete details, see Installation Instructions packed with Natural gas. Exhaust hood must be used . Pipe-joint compounds resistant to the outside. 4" (102 mm) diameter vent is required. VENTING REQUIREMENTS
Exhaust venting: Exhaust your dryer to the action of L.P.
Dimensions are recommended. Specifications subject to avoid kinking.
■...
Installation Guide - Page 5
... greater than 1" (25 mm), install Extended Dryer Feet Kit, Part Number 279810. For further information, please reference the "Assistance or Service" section of the door are acceptable.
■■ Companion appliance spacing should be required for purchase.
At lower temperatures, the dryer might be at temperatures below 45°F (7°C). Some codes limit, or do not...
Installation Guide - Page 7
... reference the "Use and Care Guide."
Use a wrench to finish turning legs until it is close to convert the dryer from the gas specified on the model/serial rating plate for the type of gas in the absence of local codes, with the type of gas available, please reference the "Assistance or Service" section of your home.
LP...
Installation Guide - Page 8
... In Canada: An individual manual shut-off valve
Gas supply connection requirements
There are some guidelines for each 1,000 ft. (305 m) increase in accordance with the B149.1, Natural Gas and Propane Installation Code. Dryer gas pipe
■■ The gas pipe that complies with the National Fuel Gas Code, ANSI Z223.1.
rating shown on the model/serial number plate. E C
A
D
■...
Installation Guide - Page 9
... extended and supported in final dryer location. ■■ Remove excess to whether the dryer is not plugged with a quali ed electrician or service representative or personnel if you are in death, fire, or electrical shock.
■■ 120 Volt, 60 Hz., AC only, 15-
Replace plastic or metal foil vents with all governing codes and...
Whirlpool WGD4910XQ Reviews
We have not received any reviews for Whirlpool yet.